Rolling-forging
General Bulk Deformation
Q: What are bulk deformation processes?
A: Metal forming operations causing significant shape change by plastic flow of bulk forms like bars, billets, or slabs.
Q: Name the four basic bulk deformation processes.
A: Rolling, forging, extrusion, wire and bar drawing.
Q: What is a key benefit of hot working in bulk deformation?
A: Allows significant shape change due to reduced strength and increased ductility.
Q: How does cold working enhance bulk deformation parts?
A: Increases strength through strain hardening.
Q: What does "near net shape" mean in bulk deformation?
A: Parts require little or no subsequent machining.
Q: What are typical starting forms for bulk deformation?
A: Cylindrical bars, billets, rectangular billets, and slabs.
Rolling
Q: What is rolling in metalworking?
A: A process where slab or plate thickness is reduced by compressive forces between opposing rolls.
Q: What percentage of deformed materials undergo rolling?
A: Over 90%.
Q: What is flat rolling used for?
A: Reducing thickness of a rectangular cross section.
Q: What is shape rolling?
A: Forming a square cross section into shapes like I-beams or rails.
Q: What is the purpose of backing rolls in a four-high rolling mill?
A: To support smaller work rolls and reduce deflection.
Q: How does a tandem rolling mill operate?
A: Uses a sequence of two-high mills for continuous reduction.
Q: What is a common defect in flat rolling due to high friction?
A: Wavy edges.
Q: What causes alligatoring in rolling?
A: Excessive deformation or sticking leading to surface splitting.
Q: What is the role of camber in rolling mills?
A: Compensates for roll bending to ensure uniform strip thickness.
Q: Why is hot rolling more common than cold rolling?
A: It allows large deformations due to lower material strength.
Q: What improves in cold-rolled sheet compared to hot-rolled?
A: Surface finish and dimensional tolerances.
Q: What is thread rolling?
A: A cold working process to form threads on cylindrical parts using dies.
Q: What is an advantage of thread rolling over machining?
A: Stronger threads due to work hardening.
Q: What does ring rolling produce?
A: Thin-walled rings of larger diameter from thick-walled rings.
Rolling-Related Processes
Q: What is roll piercing used for?
A: Creating seamless tubes by exploiting internal cracks in a compressed bar.
Q: What controls the hole size in roll piercing?
A: A mandrel.
Q: What is roll forging also known as?
A: Cross-rolling.
Q: What are examples of roll-forged products?
A: Tapered leaf springs and knives.
Q: What happens in ball rolling?
A: Steel balls are formed by skew-rolling or upsetting for bearings.
Forging
Q: What is forging?
A: Controlled plastic deformation of metal into a predefined shape by pressure or impact.
Q: How old is the forging process?
A: Dates back to about 5000 BC.
Q: What is an advantage of forging over casting?
A: Work hardening increases strength.
Q: What are the three main types of forging dies?
A: Open-die, impression-die, flashless.
Q: What is open-die forging also called?
A: Upsetting or upset forging.
Q: What causes barreling in open-die forging?
A: Friction between work and die surfaces.
Q: What is the role of flash in impression-die forging?
A: Constrains metal flow to fill the die cavity.
Q: Why is impression-die forging often manual?
A: Requires skilled operators under adverse conditions.
Q: What is a limitation of impression-die forging?
A: Not capable of close tolerances; machining is often needed.
Q: How does flashless forging differ from impression-die forging?
A: No excess flash is created; the work is fully constrained.
Q: What is coining in forging?
A: A flashless process to mint coins with sharp details.
Q: What is upsetting used for?
A: Forming heads on nails, bolts, and similar hardware.
Q: What is swaging?
A: A process using rotating dies to taper a workpiece radially.
Q: What is a typical swaged product?
A: Tapered rods or tubes.
Q: What equipment applies an impact load in forging?
A: Drop hammers (gravity or power).
Forging Equipment and Economics
Q: What is the speed range of a hydraulic forging press?
A: 0.06-0.30 m/s.
Q: Which forging equipment has the highest speed range?
A: Counterblow hammer (4.5-9.0 m/s).
Q: Why are hydraulic presses expensive in forging?
A: High initial cost, though easier to maintain.
Q: When is forging more economical than casting for a connecting rod?
A: For large quantities.
Q: What reduces setup and tooling costs in forging?
A: Increasing the number of pieces forged with the same die.
Extrusion
Q: What is extrusion?
A: A process forcing metal through a die opening to form a uniform cross-sectional shape.
Q: What are the two basic types of extrusion?
A: Direct (forward) and indirect (backward/reverse).
Q: What is the "butt" in direct extrusion?
A: The small portion of billet that cannot be forced through the die.
Q: Why is indirect extrusion limited?
A: Lower rigidity of the hollow ram and difficulty supporting the extruded product.
Q: What enhances grain structure in cold extrusion?
A: Work hardening.
Q: What is a disadvantage of cold extrusion?
A: High stresses on machinery and die wear without lubrication.
Q: What defect can occur in extrusion with high friction?
A: Pipe (extrusion) defect.
Q: What is impact extrusion?
A: High-speed cold extrusion, often for collapsible tubes.
Q: What should be avoided in extruded cross-section design?
A: Sharp corners and non-uniform thicknesses.
Wire and Bar Drawing
Q: How does wire drawing differ from extrusion?
A: Work is pulled through the die instead of pushed.
Q: What is the typical cross-sectional shape in wire drawing?
A: Circular.
Q: What distinguishes wire drawing from bar drawing?
A: Wire drawing uses smaller diameter stock (down to 0.03 mm).
Q: What limits the maximum reduction per pass in drawing?
A: Draw stress exceeding the yield strength causes elongation instead of reduction.
Q: What is the purpose of annealing in wire drawing?
A: Relieves work hardening between dies.
Q: What is a common product of bar drawing?
A: Metal bars for machining or forging.