Abrasive and Jet Machining Processes - Advanced Manufacturing Techniques

Mechanical Energy Based Machining Processes

  • Mechanical energy based processes covered within the curriculum include:
    • Abrasive Jet Machining (AJM)
    • Ultrasonic Machining (USM)
    • Water Jet Machining

Abrasive Jet Machining (AJM)

  • Abrasive Jet Machining is a non-conventional machining process where fine abrasive particles are blended with a high-pressure carrier gas.
  • This mixture is directed through a specialized nozzle onto the surface of a workpiece at high velocity.
  • Standard operational parameters for AJM include:
    • Abrasive particle size: ranging from 1010 to 40 μm40\,\mu\text{m}.
    • Carrier gas or air velocity: approximately 200200 to 400 m/s400\,\text{m/s}.
  • Material removal is achieved through the impact of these high-velocity abrasive particles, which cause erosion of the workpiece surface.
  • The specific mechanisms governing material removal are micro-cutting and brittle fracture.

Material Suitability for AJM

  • AJM is primarily utilized for machining materials with the following characteristics:
    • Hard and brittle materials.
    • Thin materials.
    • Materials that are sensitive to thermal changes or heat.
    • Materials with a inherent tendency to chip or break away easily.

Principal Mechanics of Abrasive Jet Machining

  • The fundamental energy transformation in AJM is represented by the following sequence:
    • Pressure energy →\rightarrow Kinetic energy →\rightarrow High-velocity abrasive jet →\rightarrow Impact →\rightarrow Erosion →\rightarrow Material removal.
  • Carrier gas is supplied under high pressure. This pressure energy is converted into kinetic energy to produce a high-velocity stream that carries the abrasive particles.
  • While the gas acts as the carrier, it is not the primary cutting medium; the particles striking the surface perform the micro-cutting and brittle fracture required for removal.

Major Components of the AJM System

  • The complete AJM system is constructed from five major components:
    1. Gas propulsion system
    2. Abrasive feeder
    3. Mixing chamber
    4. AJM nozzle
    5. Abrasive particles

Detailed Component Functions: Propulsion, Feeding, and Mixing

  • Gas Propulsion System:

    • Supplies clean, dry carrier gas (typically air, nitrogen (N2)(N_2), or carbon dioxide (CO2)(CO_2)) to propel the abrasives.
    • Gas is sourced from either a cylinder or a compressor.
    • When using a compressor, an air filter combined with a dryer is mandatory to prevent water or oil from contaminating the abrasive powder.
    • The propellant must be non-toxic, inexpensive, and easily available; it should not spread excessively when discharged from the nozzle.
    • Propellant consumption is approximately 0.008 m3/min0.008\,\text{m}^3/\text{min} at a nozzle pressure of 5 bar5\,\text{bar}.
    • Abrasive flow rates vary based on the task: 22 to 4 g/min4\,\text{g/min} for fine machining and 1010 to 20 g/min20\,\text{g/min} for cutting operations.
  • Abrasive Feeder:

    • Abrasive particles are supplied via a sieve system.
    • The sieve operates at a vibration frequency of approximately 50–60 Hz50\text{--}60\,\text{Hz}.
    • The amplitude of these vibrations is used to control the mixing ratio and the abrasive feed rate.
  • Mixing Chamber:

    • This component receives the particles from the feeder and facilitates their uniform mixing with the carrier gas before sending the mixture to the nozzle.

The AJM Nozzle

  • Nozzles are constructed from highly wear-resistant materials:
    • Sapphire: Typically has a service life of approximately 300 hours300\,\text{hours}.
    • Tungsten Carbide: Usually has a service life between 2020 and 30 hours30\,\text{hours}.
  • Nozzle cross-sections may be circular or rectangular.
  • The nozzle head can be configured as straight or at a right angle.
  • The design focuses on minimizing pressure loss resulting from friction and bends.
  • As a nozzle wears, the jet stream divergence increases, which leads to stray cutting and a decrease in machining accuracy.

Abrasive Materials and Applications

  • Aluminum Oxide (Al2O3)(Al_2O_3), Sizes 1212, 2020, or 50 μm50\,\mu\text{m}: Utilized for cleaning, cutting, and deburring.
  • Silicon Carbide (SiC)(SiC), Sizes 2525 or 40 μm40\,\mu\text{m}: Used for similar applications as Aluminum Oxide but specifically for harder materials.
  • Glass Beads, Sizes 0.6350.635 to 1.27 mm1.27\,\text{mm}: Applied to create a matte finish on surfaces.
  • Dolomite, 200 mesh200\,\text{mesh}: Used for etching and polishing processes.
  • Sodium Bicarbonate, 27 μm27\,\mu\text{m}: Used for cleaning, deburring, and cutting of soft materials; applicable for light finishing at temperatures below 50 ∘C50\,^{\circ}\text{C}.

Advantages and Disadvantages of AJM

  • Advantages:

    • Capability to machine thin sections of brittle materials easily.
    • Zero direct contact between the tool and the workpiece, resulting in minimal surface damage.
    • Flexibility to machine intricate cavities and holes of any shape.
    • Low initial investment requirements compared to alternative methods.
    • Small power consumption footprint.
  • Disadvantages:

    • Limited suitability; Material Removal Rate (MRR) is only high for brittle materials.
    • Poor machining accuracy, generally limited to ±50 μm\pm 50\,\mu\text{m}.
    • Low Material Removal Rate, maximized at approximately 0.05 cm/hr0.05\,\text{cm}/\text{hr}.
    • Potential for abrasive particles to become embedded in the workpiece, necessitating post-machining cleaning.
    • Abrasive powder cannot be reused once it has been through the process.
    • Environmental pollution risks associated with the process.

Ultrasonic Machining (USM)

  • Ultrasonic Machining is a non-conventional process where a tool vibrates at an ultrasonic frequency while acting on abrasive particles within a slurry.
  • The vibrating tool drives abrasive particles against the workpiece, removing material in the form of small chips via fracture and erosion.
  • USM utilizes vibrations in the frequency range of 2020 to 30 kHz30\,\text{kHz}.
  • The term "ultrasonic" denotes vibratory waves with a frequency exceeding the upper threshold of human hearing.

Principles of USM Operation

  • The fundamental principles of USM follow this sequence of energy conversion:
    • Electrical energy →\rightarrow Ultrasonic vibration →\rightarrow Tool vibration →\rightarrow Abrasive impact →\rightarrow Fracture/erosion →\rightarrow Material removal.
  • A high-frequency electrical signal is delivered to an ultrasonic transducer.
  • The transducer converts this electrical energy into mechanical vibrations.
  • Vibrations are transmitted and amplified as necessary by a horn or concentrator.
  • The vibrating tool impacts abrasive particles that are trapped in the slurry between the tool and the workpiece, causing them to strike the surface and induce material removal through erosion and fracture.