Day 1
Federal Aviation Regulations (FAR) and Regulatory Framework
The primary source for regulatory information at Frontier Airlines is myfrontier.org under the Maintenance and Engineering page, which links directly to the FAA website.
Maintenance personnell are governed under several specific chapters of the Federal Aviation Regulations (FARs): - FAR Part : Covers maintenance, preventive maintenance, rebuilding, and alteration of aircraft, specifically governing what is written in logbooks. - FAR Part : Governs the certification of flight crewmembers other than pilots and specifics regarding licenses and what holders can and cannot do. - FAR Part : Specifically (General Privileges and Limitations) and (Recency of Experience). - FAR Part : Frontier operates as a " Operator," which applies to all commercial carriers.
Personnel Certification and Experience Requirements
Address Changes: Per FAR , mechanics have days to update their address on the FAA website. A new physical license is not required, but company notification is mandatory.
General Privileges (FAR ): A certified mechanic may only exercise privileges if they understand the current instructions of the manufacturer and maintenance manuals. Mechanics must be able to read, write, and understand the English language because all manuals are written in English.
Recency of Experience (FAR ): To be considered current, a mechanic must have, within the preceding months, for at least months: - Worked as an A&P (Airframe and Powerplant) mechanic. - Supervised mechanics. - Supervised maintenance in an executive capacity. - Engaged in any combination of the above.
Temporary Certificates: These are valid for only days. If the permanent card is not received near the end of this window, mechanics must contact the FAA certification branch (the VISTA office at the airport).
Loss of License: If a certificate is suspended, revoked, or surrendered, the employee must immediately notify their supervisor, Frontier Human Resources, and the Training department to be placed "on hold" in the TRAX system.
Maintenance Performance and Record Keeping
Performance Rules (FAR ): Work must be performed using methods, techniques, and practices prescribed in the current manufacturer maintenance manuals.
Original Configuration Rule: Repairs must be executed in a manner that ensures the aircraft is at least "equal to its original properly altered condition." Historically, the rule required "equal to or greater than," but over-strengthening areas was found to cause fatigue and damage in adjacent weaker areas.
Maintenance Record Entries (FAR ): Every person performing maintenance must make a record entry including: - A description of the work performed. - The date of completion. - The signature of the person approving the work. - The type and number of the certificate held by the approving person.
Falsification of Records (FAR ): Making fraudulent or intentionally false entries, reproductions, or alterations is prohibited and leads to certificate suspension or revocation.
Logbook Integrity: Only the person who signed a write-up is authorized to make changes to it; unauthorized changes constitute falsification.
Communication and Ground Operations
Flight Operations Manual (FOM) : Governs communication in the cockpit.
Flight Recorders: The Cockpit Voice Recorder (CVR) and Flight Data Recorder (DFDR) begin recording as soon as engines are started.
Sterile Cockpit: During ground operations involving taxiing, communication must be business-only. Taxiing is defined as the movement of the aircraft under its own power on the surface of the aircraft.
Case Study: Atlanta Runway Incursion: Incurred while taxiing from the ramp to the gate due to improper repetition of Air Traffic Control (ATC) instructions. Involved personnel lost run taxi privileges for months and faced NTSB investigation.
Frontier Maintenance Information Systems (FMIS)
TRAX: This is the primary FMIS used for all aircraft records, training jackets, and task entries.
SCOUTS: Used for maintenance training with Single Sign-On (SSO) capabilities.
AirNavX: The digital platform for Airbus manuals. Use customization code "FFT" because Airbus already uses "F9" for another entity.
Search Entities in AirNavX: - MSN: Manufacturer Serial Number. - TN: Tail Number. - FSN: Fleet Serial Number (at Frontier, FSN and TN are identical).
MCDU (Multi-control Display Unit): Often called the "McDoo." It is used to generate a Post Flight Report (PFR) which details issues from the aircraft’s last leg.
Manuals and Documentation Types
General Maintenance Manual (GMM): The definitive source for Frontier’s policies, programs, and procedures. It is divided into chapters, sections, and subsections.
Time Controlled Index (TCI): Coupled with the GMM to manage the Continuous Airworthiness Maintenance Program (CAMP).
Component Maintenance Manual (CMM): Used for parts not manufactured by Airbus, such as ACRO seats.
Minimum Equipment List (MEL): Governs which equipment can be inoperative for flight.
Troubleshooting Manual (TSM): Used for diagnosing faults using fault codes from PFRs.
Data Classification: - Accepted Data: Data accepted by the FAA but not specifically approved, including AMMs (Aircraft Maintenance Manuals), Service Bulletins (SB), and Advisory Circulars. - Approved Data: Data that must be FAA-blessed for major repairs/alterations, including TCDS (Type Certificate Data Sheets), STCs (Supplemental Type Certificates), and ADs (Airworthiness Directives).
Safety Symbols and Regulatory Action Designations
Warnings: Written in RED (symbolizing they are "written in blood"). They indicate procedures that could result in personal injury.
Cautions: Indicated procedures that could result in damage to equipment.
Notes: Procedures essential to emphasize contained information.
FAA Action Acronyms: - CA (Corrective Action): Policy changes agreed upon between the airline and FAA. - VDRP (Voluntary Disclosure Reporting Program): Allows the airline to report a self-discovered error (like missing safety pins on emergency slides) to avoid heavy fines. - LOI (Letter of Investigation): Initiated when the FAA discovers an infraction before the airline reports it.
Fines: The FAA can fine up to per leg. An aircraft flying legs a day for days could incur a fine of .
Station Classifications and Maintenance Organization
Class : Major facilities (e.g., PIMCO in Tampa, Lufthansa Technik in Puerto Rico) capable of all scheduled checks including C-checks and Airworthiness Releases.
Class : Facilities capable of checks up to A-checks and subparts of C-checks.
Class : Facilities limited to Heavy Service Checks and below.
Class : Facilities limited to Service Checks and unscheduled maintenance.
On-Call: Contractors who perform only unscheduled maintenance and receive manual portions from Maintenance Control as needed.
Operational Standards: Shift Turnover and Duty Time
Form : The Shift Turnover Log used to ensure continuity of work between off-going and oncoming shifts.
Form : Used for documenting non-routines and partial work. Mechanics must sign the left side of a task card line to indicate partial completion.
Duty Time Limits: - Maximum duty day is hours. - Must have a -hour rest period every consecutive days. - Must have four -hour off-duty periods every days.
Field Trips: Road trips are assigned via a rotating list. Per diem is based on government standards (e.g., per day in Orlando).
Safety Critical Procedures: Circuit Breakers and Recorders
Circuit Breaker Policy: Resetting a tripped breaker by "unknown cause" is a maintenance function. Resetting in-flight is prohibited for fuel boost pumps and fuel quantity indicators.
Flight Recorders (CVR/DFDR): If an aircraft is in an accident requiring NTSB notification, recorded media must be preserved for at least days.
DFDR Removal: If a DFDR is robbed/swapped, the data must be downloaded first. FAA standards now often require two recorders (front and back) to ensure survival in various crash scenarios.
Questions & Discussion
Participant Question: "What does this application do?" (Referring to M&E applications).
Response: It is the system for accessing CMMs (Component Maintenance Manuals) for all parts not made by Airbus.
Participant Question: "Do we do fuel tank work?"
Response: No, Frontier uses specialized "tank tigers" or contractors because the cost of certifying every mechanic for tank entry and annual recertification is prohibitive.
Participant Question: "Where did you go to get [to the CMMs]?"
Response: Under Departments > Maintenance and Engineering > M&E Applications > FMS Systems.