Comprehensive Study Notes on Concrete Production and Properties
Learning Outcomes
- 01 Know the materials used in the production of concrete and understand its properties
- 02 Describe the effect of adding excess water and admixtures to a concrete mix
- 03 Discuss the methods used to strengthen concrete products
- 04 Describe how to test concrete for workability and compressive strength
Concrete: The Basics - Composition
Concrete consists of:
- Cement
- Fine Aggregate (Sand)
- Coarse Aggregate (Gravel)
- WaterWater's Role in Concrete:
- Required to make the mix workable
- Allows accurate finished levels
- Provides a range of surface finishes
- Excess Water weakens the mix
Hydration of Cement
- Hydration is the chemical reaction between cement and water, leading to the hardening of concrete.
Properties of Concrete
- Strength Under Compression:
- Concrete is very strong under compression, meaning it can withstand substantial loads without collapsing. - Weakness Under Tension:
- Concrete is quite weak under tension, which means it can fail or crack when stretched or pulled.
Strengthening Concrete
- To compensate for the weakness in tension:
- Concrete is reinforced with materials (e.g., steel) that possess high tensile strength. - This results in a composite material that exhibits good performance under both compressive and tensile forces.
Prestressed Concrete
- Definition:
- Prestressed concrete applies a pre-compression to counteract tensile stresses that may occur under load. - Application:
- Used in high loading situations to reduce deflection and cracking.
Concrete Composition Ratios
- Mix Ratios for Various Grades of Concrete:
- M5: 1:5:10
- Cement: 138.6 kg
- Sand: 770 kg
- Aggregate: 1463 kg
- Water: 55.44 L
- Typical usage: Blinding concrete.
- M7.5: 1:4:8
- Cement: 170.58 kg
- Sand: 758.15 kg
- Aggregate: 1440.49 kg
- Water: 68.232 L
- Typical usage: Mass concrete.
- M10: 1:3:6
- Cement: 221.76 kg
- Sand: 739.2 kg
- Aggregate: 1404.48 kg
- Water: 99.792 L
- Typical usage: Light reinforced concrete.
- M15: 1:2:4
- Cement: 316.8 kg
- Sand: 704 kg
- Aggregate: 1337.6 kg
- Water: 158.4 L
- Typical usage: Reinforced concrete/precast concrete.
- M20: 1:1.5:3
- Cement: 403.2 kg
- Sand: 672 kg
- Aggregate: 1276.8 kg
- Water: 201.6 L
- Typical usage: Heavy reinforced concrete.
- Other Ratios: M25, M30, etc. have similar detailed entries with their specific ratios.
Density of Materials
- Densities:
- Cement: 1440 kg/m³
- Sand: 1600 kg/m³
- Aggregate: 1560 kg/m³
Water-Cement Ratio
- Definition:
- The water-cement ratio is the ratio between the weight of water to the weight of cement. - Range: Typically between 0.4 to 0.6.
- Effect on Concrete: Directly impacts both strength and workability.
- Example calculation: For 50 kg of cement with a ratio of 0.5, require 25 kg of water.
Testing Concrete
Slump Test
- Purpose: Assesses the consistency of fresh concrete.
- Procedure:
- A steel slump cone is filled in three equal layers.
- Each layer rodded 25 times for compaction.
- After lifting the cone, the difference in height of the concrete tells the slump. - Results Interpretation:
- True Slump:
- < 50 mm: Strong but unworkable. - 75-100 mm: Normal range. - > 150 mm: Easy to lay but potentially weak unless designed for flow properties.
Cube Test
- Used to check the compressive strength of concrete to evaluate quality and integrity.
Joints in Concrete
- Shrinkage and Temperature: Concrete shrinks in volume as it sets and expands/contracts with temperature changes.
- Need for contraction and expansion joints to manage stress and prevent cracking.
Curing of Concrete
- Concrete may visibly set within a few hours, initially set within 7 days, but takes 28 days to reach maximum crushing strength.
- Best Practices:
- Avoid cold weather and frost.
- Prevent rapid water loss.
- Avoid heavy loads during curing.
Additives in Concrete
- Types of Additives:
- Plasticisers: Increase workability.
- Retardants: Slow down setting rate for premixed loads.
- Accelerators: Increase early strength gain.
- Air-entraining agents: Produce small air bubbles for added durability.
Application of Concrete on Farms
- Concrete is commonly used in various farm components including structures for livestock, storage, and operational areas.
Further Information
- Resources:
- British Ready Mixed Concrete Association
- Agricultural Notebook (Primrose McConnell)
- Building Construction Workbook - Teagasc
- Websites for videos and additional concrete resources.