Term 3: Electrical and Electronic Systems

Electrical Systems and Circuit Fundamentals

  • Component Representations and Circuit Schematics:

    • Electric circuits are represented using standard graphical symbols to illustrate the interconnection of energy sources, control devices, and output loads.
    • A circuit must form an unbroken, continuous closed loop for electric charge to circulate and perform work.
  • Behavior of Cells in Series and Parallel Configurations:

    • Cells in Series: Connecting two or more cells in series increases the total potential difference (voltage) delivered to the circuit (Vtotal=V1+V2+…V_{\text{total}} = V_1 + V_2 + \dots). When cells are placed in series, they provide more electrical pressure, causing an attached load, such as an incandescent lamp, to shine much more brightly than it would with a single cell.
    • Cells in Parallel: Connecting cells in parallel does not increase the output voltage; the circuit voltage remains identical to that of a single cell. Instead, parallel cells increase the total energy storage capacity of the energy source. This extended capacity enables the cells to sustain current for a significantly longer duration before going flat.
  • Behavior of Lamps in Series and Parallel Connections:

    • Lamps in Series: When two or more lamps are connected in series along the same conductive loop, the electrical resistance of the circuit increases, and the supply voltage is divided across the lamps. As a result, each lamp shines less brightly than a single lamp connected on its own to the same power source.
    • Lamps in Parallel: When lamps are connected in parallel, each lamp is connected across the full potential difference of the energy source. Consequently, each parallel lamp shines with the same brightness as a single lamp operating independently.
  • Logic Gates Using Mechanical Switches:

    • AND Logic Gate: Formed by connecting two or more switches in series along the same path. Current can flow to energise the output load only if Switch 1 AND Switch 2 are closed simultaneously. If either switch is open, the circuit remains broken.
    • OR Logic Gate: Formed by connecting two or more switches in parallel with each other. Current can flow to energise the load if Switch 1 OR Switch 2 (or both) is closed, providing alternative conductive pathways.
  • Conventional Current Flow:

    • By international convention, electrical current is defined as moving from the positive (++ ) terminal of the power source, through the external circuit, and into the negative (−- ) terminal.

Ohm's Law and Circuit Resistance

  • Verbatim Principle of Ohm's Law:

    • The current strength through a conductor is directly proportional to the potential difference across the conductor, provided that the resistance of the conductor remains constant.
    • Mathematically, this relationship is expressed as:     VI=Constant=R\frac{V}{I} = \text{Constant} = R
  • Core Quantities and Units of Measurement:

    • Potential Difference (Voltage, VV): Measured in volts (V\text{V} ).
  • Current Strength (II): Measured in amperes (A\text{A} ).

  • Resistance (RR): Measured in ohms (Ω\Omega ).

  • Action Research: Testing Ohm's Law:

    • Required Apparatus: Three electrical cells, an SPST switch, a 15 Ω15\,\Omega, 20 W20\,\text{W} ceramic wire-wound power resistor, connecting wires or leads with crocodile clips, a DC voltmeter, and a DC ammeter.
    • Conductor Selection (Resistor vs. Lamp): A fixed resistor is used rather than an incandescent lamp because a lamp's filament increases in temperature as current flows, causing its resistance to rise significantly. A fixed resistor maintains nearly constant resistance as its temperature varies slightly, satisfying the condition necessary to demonstrate Ohm's Law.
    • Instrument Connections:
    • Ammeter: Connected in series with the resistor to measure the full current strength passing through it. The lead from the black negative terminal socket of the ammeter connects to the resistor, while the other lead (from the red socket marked '50 mA50\,\text{mA}' or higher current range) connects to the switch.
    • Voltmeter: Connected in parallel across the resistor to measure the potential difference across its terminals. The lead from the black negative socket connects to the left-hand lead of resistor RR, and the lead from the red socket marked '3 V3\,\text{V}' connects to the right-hand lead of resistor RR.

Ammeter and voltmeter connections

  • Testing Procedure and Graphical Analysis:

    • The circuit is energized using one cell, and the corresponding voltage (VV ) and current (II ) readings are noted before switching off.
  • A second cell is added in series, and the measurements are repeated.

  • A third cell is connected in series, and a third set of values is recorded.

  • Plotting current strength (II ) on the vertical axis against potential difference (VV ) on the horizontal axis produces a straight-line graph passing through the origin, confirming direct proportionality (I∝VI \propto V ).

  • Mathematical Formulations and Circuit Calculations:

    • The fundamental formula can be algebraically rearranged into three operational forms:
    • Calculating Resistance: R=VIR = \frac{V}{I}
    • Calculating Potential Difference: V=I×RV = I \times R
    • Calculating Current Strength: I=VRI = \frac{V}{R}
  • Worked Examples:

    • Calculating Resistance: A downlight lamp operates on a 12 V12\,\text{V} supply drawing a current of 3 A3\,\text{A}.     R=VI=12 V3 A=4 ΩR = \frac{V}{I} = \frac{12\,\text{V}}{3\,\text{A}} = 4\,\Omega
    • Calculating Potential Difference: An electronic designer requires the voltage across a 240 Ω240\,\Omega resistor when passing 0,02 A0{,}02\,\text{A}.     V=R×I=240 Ω×0,02 A=4,8 VV = R \times I = 240\,\Omega \times 0{,}02\,\text{A} = 4{,}8\,\text{V}
    • Calculating Current Strength: A small passenger car starter motor operates from a 12 V12\,\text{V} battery with a motor resistance of 0,1 Ω0{,}1\,\Omega.     I=VR=12 V0,1 Ω=120 AI = \frac{V}{R} = \frac{12\,\text{V}}{0{,}1\,\Omega} = 120\,\text{A}
    • High-Current Applications: Large heavy-duty vehicles, such as transport trucks, draw starter currents exceeding 300 A300\,\text{A}. To supply this current without excessive losses, trucks connect two large 12 V12\,\text{V} lead-acid batteries in series to generate a 24 V24\,\text{V} supply system.
    • Supplementary Practical Exercises:
    • Given V=32 VV = 32\,\text{V} and I=0,2 AI = 0{,}2\,\text{A}:       R=32 V0,2 A=160 ΩR = \frac{32\,\text{V}}{0{,}2\,\text{A}} = 160\,\Omega
    • Given I=0,3 AI = 0{,}3\,\text{A} and R=30 ΩR = 30\,\Omega:       V=0,3 A×30 Ω=9 VV = 0{,}3\,\text{A} \times 30\,\Omega = 9\,\text{V}

Resistor Colour Codes and Tolerance Specifications

  • Colour Band Structure:

    • Low-value power resistors often have their resistance values printed directly on their bodies. Carbon-composition and metal-film resistors used in consumer electronics (such as televisions and audio amplifiers) utilize a standard four-band colour code.
    • Band 1 (First band from left): Represents the first significant digit of the resistance value.
    • Band 2 (Second band from left): Represents the second significant digit of the resistance value.
    • Band 3 (Third band from left): Multiplier indicating the number of zeros to append after the first two digits.
    • Band 4 (Fourth band, spaced to the right): Accuracy rating (tolerance) indicating the maximum percentage variance of actual resistance from nominal coded value.
  • Resistor Colour Decoder Chart:

    • Black: Digit 00, Multiplier factor (no zeros added / ×100\times 10^0 )
  • Brown: Digit 11, Multiplier factor 00 (one zero / ×101\times 10^1 )

  • Red: Digit 22, Multiplier factor 0000 (two zeros / ×102\times 10^2 )

  • Orange: Digit 33, Multiplier factor 000000 (three zeros / ×103\times 10^3 )

  • Yellow: Digit 44, Multiplier factor 00000000 (four zeros / ×104\times 10^4 )

  • Green: Digit 55, Multiplier factor 0000000000 (five zeros / ×105\times 10^5 )

  • Blue: Digit 66, Multiplier factor 000000000000 (six zeros / ×106\times 10^6 )

  • Violet: Digit 77, Multiplier factor 00000000000000 (seven zeros / ×107\times 10^7 )

  • Grey: Digit 88, Multiplier factor 0000000000000000 (eight zeros / ×108\times 10^8 )

  • White: Digit 99, Multiplier factor 000000000000000000 (nine zeros / ×109\times 10^9 )

  • Accuracy Ratings (Tolerance):

    • Manufacturing processes cannot guarantee exact resistance values. The fourth band identifies tolerance limits:
    • Red: ±2%\pm 2\%  tolerance (highest precision grade)
    • Gold: ±5%\pm 5\%  tolerance (intermediate commercial grade)
    • Silver: ±10%\pm 10\%  tolerance (standard utility grade)
    • A resistor rated at 300 Ω300\,\Omega with a 5%5\%  gold tolerance band can have an actual physical resistance anywhere between 285 Ω285\,\Omega and 315 Ω315\,\Omega (such as 312 Ω312\,\Omega ).
  • Worked Decoding Examples:

    • Example 1: A resistor with bands Green, Orange, Red, and Gold:
    • Band 1 = Green (55 )
  • Band 2 = Orange (33 )

  • Band 3 = Red (22 zeros, or 0000 )

    • Base Value = 5 300 Ω5\,300\,\Omega
    • Band 4 = Gold (±5%\pm 5\% accuracy rating)
    • Final Value: 5 300 Ω±5%5\,300\,\Omega \pm 5\%
  • Example 2: A resistor with bands Yellow, Orange, Brown, and Red:

    • Band 1 = Yellow (44 )
  • Band 2 = Orange (33 )

  • Band 3 = Brown (11 zero, or 00 )

  • Base Value = 430 Ω430\,\Omega

  • Band 4 = Red (±2%\pm 2\% accuracy rating)

  • Final Value: 430 Ω±2%430\,\Omega \pm 2\%

Resistor colour code decoding

Electronic Systems and Switching Mechanisms

  • Electronic vs. Manual Switching:

    • Manual switches are operated directly by human hands to connect or disconnect physical contacts.
    • Electronic switching relies on semiconductor components (such as transistors) responding to electrical input signals. Electronic switches can cycle millions of times per second, which is necessary for high-speed digital computing and information processing where mechanical switches are too slow.
  • Anatomy and Terminology of Manual Switches:

    • Pole: The moving electrical contact inside the switch mechanism that redirects or interrupts current.
    • Throw: The number of independent conductive contact paths available to each pole.
    • Single-Pole, Single-Throw (SPST): Contains one moving pole that can make or break contact in a single direction (e.g., standard paper-clip switch or simple toggle).
    • Single-Pole, Double-Throw (SPDT): Contains a single moving pole capable of being thrown between two alternate contact terminals. This allows current to be directed toward one of two separate circuit branches.
    • Double-Pole, Double-Throw (DPDT): Contains two separate moving poles mechanically linked to throw simultaneously between two pairs of contacts, allowing two isolated circuits to be controlled in tandem.
    • Commercial Switch Designs: Include rocker switches (pivoting actuators), rotary switches (circular dials selecting positions), and push switches (momentary or latching spring-loaded buttons, such as emergency stops).

SPDT and DPDT switch symbols and circuits

  • Two-Way Lamp Selection Circuit:
    • Using an SPDT switch connected to two lamps in parallel branches from an energy source, throwing the switch to terminal A completes the circuit for Lamp 1 exclusively. Throwing the switch to terminal B redirects the current loop through Lamp 2 exclusively.

Semiconductor Diodes and Light-Emitting Diodes (LEDs)

  • Semiconductor Diode Construction and Unidirectional Conduction:

    • A diode is a two-terminal electronic semiconductor component that allows electrical current to pass freely in only one direction, termed the forward direction.
    • Anode (++ ): The electrode that must be connected to the positive side of the supply voltage for current conduction.
  • Cathode (−- ): The electrode that must be connected to the negative side of the supply voltage for current conduction.

    • When connected in reverse (cathode to positive, anode to negative), the diode blocks current flow, behaving as an open switch.
  • Diode Rectification:

    • Commercial power distribution supplies alternating current (AC), which periodically reverses its direction of flow.
    • Internal electronic processing circuits require steady direct current (DC) moving in a single direction.
    • Diodes arranged as rectifiers block the negative alternation of an AC wave while conducting the positive alternation, converting alternating current into direct current (rectification).
  • Light-Emitting Diodes (LEDs):

    • Specialized semiconductor diodes designed to emit photons of visible light when forward-biased current passes through them.
    • Terminal Identification: An LED features two leads of unequal length. The longer lead is the anode (++ ) and the shorter lead is the cathode (−- ).
  • Forward-Biasing Requirement: Current flows only when the longer anode connects to the positive supply rail and the shorter cathode connects to the negative return rail. Reversing polarity inhibits all current and produces no light.

  • Threshold Operating Voltage: An LED cannot be illuminated using a single dry cell providing only 1,5 V1{,}5\,\text{V}, because the forward breakdown voltage is not reached. Circuits must use two or more cells in series (minimum 3 V3\,\text{V} to 4,5 V4{,}5\,\text{V} ) to enable conduction.

  • Colours and Applications: Manufactured in red, green, yellow, blue, and white. Used extensively as status indicators (on/standby displays in consumer electronics), vehicle brake lights, high-intensity vehicle headlights, traffic signal arrays, and high-efficiency flashlights.

Transistors as Switches and Amplifiers

  • Transistor Terminal Anatomy:

    • A bipolar junction transistor contains three distinct functional regions, each connected to an external terminal:
    • Base (bb ): The central control terminal that receives the input actuation signal.
  • Collector (cc ): The main current-receiving terminal connected to the primary power rail through the load.

  • Emitter (ee ): The current-discharging terminal that exits to ground or the return rail.

  • Electronic Switching Action:

    • A very weak control current fed into the base terminal switches on a much larger current flowing through the collector-to-emitter path.
    • If the base voltage/current is below the operational threshold, the collector-emitter path remains completely non-conductive (open switch).
    • Introducing a small forward current at the base triggers full conduction from collector to emitter (closed switch), allowing current to drive output devices like LEDs, relays, or buzzers.
  • Signal Amplification:

    • Weak input currents (such as the microampere-level signals generated by acoustic microphones) injected into the base are reproduced as proportional, substantially heavier currents across the collector-emitter loop.
    • This enlarged current signal can then drive substantial mechanical or acoustic transducers, such as loudspeakers.
  • Potentiometers (Variable Resistors):

    • A potentiometer (abbreviated as 'pot') is an adjustable three-terminal resistor whose resistance can be varied smoothly between 0 Ω0\,\Omega and a designated upper limit (such as 10 000 Ω10\,000\,\Omega or 20 000 Ω20\,000\,\Omega ).
  • It features two fixed outer contacts (terminals A and B) and a central rotating wiper contact (terminal S) actuated via an adjustment slot with a screwdriver.

  • Adjusting the wiper S toward terminal A reduces circuit resistance, increasing the base current supplied to the transistor to switch it on. Turning the wiper towards terminal B diverts current, starving the base and switching the transistor off.

Electronic Sensors: Light and Temperature Detection

  • Sensor Functionality:

    • Sensors act as input transducers in electronic circuits, converting environmental physical stimuli (light level, heat, moisture, mechanical force) into corresponding shifts in electrical resistance or voltage.
  • Light-Dependent Resistors (LDRs):

    • A photo-conductive component whose electrical resistance varies inversely with ambient luminous intensity.
    • Operational Behavior: As light intensity decreases (dark conditions), the resistance of an LDR increases dramatically, reaching values as high as 1 000 000 Ω1\,000\,000\,\Omega (1 MΩ1\,\text{M}\Omega ). When exposed to bright illumination or direct sunlight, its resistance plummets to between 100 Ω100\,\Omega and 130 Ω130\,\Omega.
  • LDR Test Circuit: Connecting an LDR in series with an acoustic buzzer and a 3 V3\,\text{V} battery shows clear light dependence. In a dimly lit environment, the buzzer emits a quiet tone due to high circuit resistance limiting current. Moving the assembly into bright illumination reduces the resistance, increasing current flow and producing a much louder buzzing sound.

LDR connected to buzzer and multimeter

  • Thermistors:

    • Thermally sensitive resistors whose bulk resistance changes predictably in response to fluctuations in ambient temperature.
    • Type +t+t (Positive Temperature Coefficient, PTC): Resistance increases as temperature increases.
    • Type −t-t (Negative Temperature Coefficient, NTC): Resistance increases as temperature decreases (and drops as temperature rises). For instance, a common −t-t thermistor exhibiting 1 000 Ω1\,000\,\Omega at ambient temperature (24 ∘C24\,^\circ\text{C} ) rises to approximately 2 400 Ω2\,400\,\Omega when placed inside an icy refrigeration unit.
    • Thermostatic Regulation: Used in feedback circuits for geysers (water heaters) and air-conditioning systems to maintain thermal equilibrium by cycling heating elements or cooling compressors on and off.
  • Multimeter Utilization:

    • A multi-function electronic test instrument capable of measuring potential difference (volts), current intensity (amperes/milliamperes), and electrical resistance (ohms/kilohms) across components.

Capacitance and Energy Storage

  • Internal Construction of a Capacitor:

    • A capacitor consists of two conductive metal plates separated by an intermediate layer of insulating material termed the dielectric.
    • In cylindrical electrolytic capacitors, the metal-plate and dielectric layers are stacked and tightly rolled in a cylindrical spiral, resembling a rolled-up carpet, before being sealed in an aluminum can.
  • Energy Storage Dynamics and Capacitance Units:

    • Capacitors store energy electrostatically by accumulating opposing charges on their plates.
    • Units of Capacitance: Measured in farads (F\text{F} ) and microfarads (μF\mu\text{F} ), where 1 μF=10−6 F1\,\mu\text{F} = 10^{-6}\,\text{F}.
    • Hydraulic Analogy: Charging a capacitor is analogous to pumping water into a storage reservoir. A larger tank requires more time to fill and holds more water; similarly, a capacitor with a larger capacitance takes longer to charge fully and discharges over a longer time.
  • Polarised vs. Unpolarised Capacitors:

    • Polarised Capacitors (Electrolytic): Possess distinct positive (++ ) and negative (−- ) leads. The longer lead marked with a positive polarity must connect to the positive voltage rail. Connecting a polarised capacitor backwards damages the internal dielectric layer.
    • Unpolarised Capacitors (Ceramic/Mylar): Exhibit non-directional internal construction; both leads are structurally identical and can connect to positive or negative rails without preference.
  • Charge and Discharge Cycling:

    • Charging Phase: When connected across a DC voltage source, electrons migrate, accumulating a negative charge on the plate connected to the negative terminal while leaving the opposing plate positively charged. Current flows into the plates until the potential difference across the dielectric matches the supply voltage.
    • Discharging Phase: When isolated from the supply and bridged across a resistive load, the stored charge discharges through the load, sustaining current flow until the plates reach electrical equilibrium.

Specialised Circuits and Practical Applications

  • Soil Moisture and Touch Detector Circuits:
    • Moisture and touch sensors are complete electronic circuits built around a transistor switch rather than standalone individual components.
    • Circuit Architecture: Incorporates an NPN transistor, a current-limiting protective base resistor, a potentiometer to adjust sensitivity, an indicator LED, and an intentional air gap (SS ) in the base circuit between two probe contacts, A and B.
  • Moisture Detection Mechanism: When probes A and B are inserted into moist soil with an approximate 6 mm6\,\text{mm} gap, moisture and dissolved mineral salts bridge the gap, conducting a small base current. This triggers collector current flow, lighting the LED. In dry soil, lack of conductivity keeps the base starved of current; the transistor remains off, and the LED stays unlit.
  • Human Touch Detection: When probes A and B are pressed against a person's index finger across an approximate 5 mm5\,\text{mm} gap, the natural moisture and perspiration on the skin conduct a small base current, turning the transistor on and lighting the LED.
  • Practical Safety Caveat: When testing soil moisture in the field, technicians must never dig into the soil using bare hands, as sharp glass fragments, scrap metal, or other hazardous debris may be buried just below the surface.

Practical electronic circuits including thermistor and capacitor

  • Laboratory Circuit Assemblies:
    • Circuit 1: Unidirectional Conduction of LEDs: An LED in series with a 470 Ω470\,\Omega protective resistor, an SPST switch, and a 4,5 V4{,}5\,\text{V} battery shines when forward-biased. When reversed, the LED completely blocks current and remains dark.
    • Circuit 2: Light Intensity Sensor with Acoustic Output: An LDR connected in series with an acoustic buzzer and a 3 V3\,\text{V} DC supply acts as an automatic alarm, sounding louder as light levels increase.
    • Circuit 3: Cold-Activated Transistorized Buzzer Alarm:
    • Components: NPN BD139-16 transistor, acoustic buzzer, 10 000 Ω10\,000\,\Omega (10 kΩ10\,\text{k}\Omega ) potentiometer, 1 000 Ω1\,000\,\Omega (1 kΩ1\,\text{k}\Omega ) fixed resistor, −t-t thermistor (1 000 Ω1\,000\,\Omega at 24 ∘C24\,^\circ\text{C} ), and a 6 V6\,\text{V} battery.
    • Calibration: The variable potentiometer is calibrated with a screwdriver at room temperature until base voltage drops just below conduction and the buzzer falls silent.
    • Activation: Placing the −t-t thermistor into iced water increases its resistance. In this voltage divider configuration, the rising resistance shifts base voltage upward, supplying base current to turn on the transistor and sound the buzzer.
  • Circuit 4: Capacitive Timed LED Discharge:
    • Components: 1 000 μF1\,000\,\mu\text{F} (or 4 700 μF4\,700\,\mu\text{F} ) polarised capacitor, 470 Ω470\,\Omega or 1 000 Ω1\,000\,\Omega resistor, an LED, an SPDT selector switch, and a DC battery (4,5 V4{,}5\,\text{V} to 6 V6\,\text{V} ).
  • Operation: In Switch Position 1, the capacitor charges from the battery for 1010 to 20 seconds20\,\text{seconds}, while the LED is isolated. Throwing the SPDT switch to Position 2 disconnects the battery and connects the charged capacitor across the resistor and LED. The stored energy discharges through the LED, illuminating it for several seconds until the stored charge is depleted.

Mini Practical Assessment Task: Agricultural Moisture Sensor and Irrigation Control

  • South African Hydrological Context and Water Scarcity:

    • South Africa is categorized as the 30th30^{\text{th}}  driest country in the world.
    • South Africa receives an average annual precipitation of only 500 mm500\,\text{mm}, significantly lower than the global average of 860 mm860\,\text{mm}  per year.
    • According to official records from the Department of Water and Forestry (2007 statistics), the agricultural sector is the largest consumer of water in South Africa, using 62%62\%  of all registered water supplies.
  • Problem Statement and Engineering Scenario:

    • A commercial maize crop farmer seeks to optimize water conservation during field irrigation. Standard rain gauges only indicate surface water delivery without measuring moisture depth at the root zone.
    • The engineering challenge requires designing and assembling a dual-system device: an electronic moisture sensor circuit to verify root-depth soil conditions on demand, and an independent manual switch to activate the irrigation system only when soil is dry. The entire assembly must be housed in a durable, field-ready mounting enclosure.
  • Stages of the Technological Design Process:

    • Investigation Skills (1 Hour, Week 6): Analyze water usage and root depth requirements. Select and adapt an electronic moisture-detecting transistor circuit to address the irrigation management problem.
    • Design Skills (1 Hour, Week 6): Write a structured design brief detailing technical specifications, environmental constraints, and user requirements. Draw complete circuit schematics and produce three-dimensional sketches of the casing and probe mounting assembly.
    • Making Skills (2 Hours, Week 7): Generate detailed working plans using first-angle orthographic projection, accompanied by a three-dimensional exploded assembly drawing. Build a scaled, functional prototype using workshop materials safely and accurately.
    • Communication and Assessment Skills (4 Hours, Weeks 8 & 9): Present the design to peers through technical drawings, artistic renderings, a detailed parts costing analysis, and a live demonstration of the operational model. Compile individual records into a technical workbook evaluated against rubric criteria.

Review Questions and Conceptual Exercises

  • Foundational Circuit Checks:

    • Q: What are the three essential components in a basic closed loop?
    • A: An electrical energy source (cell/battery), a control component (switch), and an output load (lamp/resistor).
    • Q: How does cell arrangement affect output voltage?
    • A: Cells in series combine their voltages additively; cells in parallel maintain single-cell voltage while increasing total capacity.
    • Q: What are the SI units and abbreviations for potential difference, current, and resistance?
    • A: Potential difference: volt (V\text{V} ); Current: ampere (A\text{A} ); Resistance: ohm (Ω\Omega ).
    • Q: In what direction does conventional current move?
    • A: From the positive terminal to the negative terminal of the power source.
  • Component Identification and Decoding:

    • Q: Which colour band represents a 2%2\%  accuracy rating on a resistor?
    • A: Red.
    • Q: Which numbers are represented by grey and yellow in the resistor colour code?
    • A: Grey represents 88 ; Yellow represents 44 .
  • Q: Decode the nominal resistance and tolerance of a resistor with bands Orange, Blue, and Red:

    • A: Orange (33 ), Blue (66 ), Red (22  zeros / 0000 ). Nominal resistance is 3 600 Ω3\,600\,\Omega (or 3,6 kΩ3{,}6\,\text{k}\Omega ).
  • Circuit Calculations:

    • Q: A potential difference of 9 V9\,\text{V} applied across a lamp draws a current of 0,45 A0{,}45\,\text{A}. Calculate the resistance of the lamp.
    • A: Applying Ohm's Law:       R=VI=9 V0,45 A=20 ΩR = \frac{V}{I} = \frac{9\,\text{V}}{0{,}45\,\text{A}} = 20\,\Omega
    • Q: A resistance wire of 5 Ω5\,\Omega has a potential difference of 12,5 V12{,}5\,\text{V} applied across it. Calculate the current passing through the wire.
    • A: Applying Ohm's Law:       I=VR=12,5 V5 Ω=2,5 AI = \frac{V}{R} = \frac{12{,}5\,\text{V}}{5\,\Omega} = 2{,}5\,\text{A}
  • Electronic Components and Controls:

    • Q: Name the component used to convert alternating current (AC) to direct current (DC).
    • A: A semiconductor diode (functioning as a rectifier).
    • Q: State two primary functions of a bipolar transistor in electronic circuits.
    • A: Electronic switching and current/voltage signal amplification.
    • Q: What type of thermistor increases its resistance as temperature rises?
    • A: A Type +t+t (Positive Temperature Coefficient / PTC) thermistor.
    • Q: What physical quantity is quantified using farads and microfarads?
    • A: Capacitance (the ability of a capacitor to store electric charge).
    • Q: How do you switch on a transistor that is currently non-conductive in an energized circuit?
    • A: Apply a sufficient forward base current (or base-to-emitter threshold voltage) to the base terminal.
    • Q: What charges develop on the plates of a capacitor connected across a DC supply?
    • A: The plate connected to the positive cell terminal accumulates a positive charge (++ ), and the plate connected to the negative cell terminal accumulates an equal negative charge (−- ).