RC and RL Time Constant Reference

1. What You Need to Know

Time constant problems are your go-to tool for quickly describing how capacitor voltages and inductor currents change after a DC switching event (step, connect/disconnect, source change). Most exam questions boil down to: find τ\tau, find the initial and final values, then write the exponential.

Core idea (single energy-storage element)

If a circuit has exactly one capacitor (and no other capacitors/inductors), or exactly one inductor (and no other capacitors/inductors), the response is first-order and looks like:

x(t)=x(∞)+(x(0+)−x(∞))e−t/τx(t)=x(\infty)+\big(x(0^+)-x(\infty)\big)e^{-t/\tau}

Where:

  • For an RC circuit, x(t)x(t) is typically vC(t)v_C(t).
  • For an RL circuit, x(t)x(t) is typically iL(t)i_L(t).
What is τ\tau?
  • RC: τ=RthC\tau=R_{\text{th}}C
  • RL: τ=LRth\tau=\frac{L}{R_{\text{th}}}

Here RthR_{\text{th}} is the Thevenin resistance seen by the capacitor/inductor terminals (looking into the rest of the circuit) with independent sources turned off.

Critical continuity rules:

  • Capacitor voltage cannot jump: vC(0+)=vC(0−)v_C(0^+)=v_C(0^-)
  • Inductor current cannot jump: iL(0+)=iL(0−)i_L(0^+)=i_L(0^-)
Why it matters
  • Lets you solve transient behavior without full differential equations.
  • Gives fast checkpoints: at t=τt=\tau you are about 63.2%63.2\% of the way from initial to final.
  • Common in timing, filters (low-frequency view), relay/coil current ramp, and power-up/down behavior.

2. Step-by-Step Breakdown

Use this exact workflow for almost every first-order RC/RL transient.

A. Universal 7-step method
  1. Identify the switching time (usually t=0t=0) and what changes.
  2. Verify it is first-order: only one energy storage element (one CC or one LL).
  3. Find the initial condition using pre-switch DC steady state:
    • At t<0t<0 with DC: capacitor →\rightarrow open circuit; inductor →\rightarrow short circuit.
  4. Apply continuity at the switch:
    • vC(0+)=vC(0−)v_C(0^+)=v_C(0^-) or iL(0+)=iL(0−)i_L(0^+)=i_L(0^-).
  5. Find the final value x(∞)x(\infty) using post-switch DC steady state:
    • For DC as t→∞t\rightarrow\infty: capacitor open; inductor short.
  6. Compute RthR_{\text{th}} seen by the element in the post-switch circuit:
    • Turn off independent sources: voltage sources →\rightarrow short; current sources →\rightarrow open.
    • Keep dependent sources active (if any). If dependent sources exist, use a test source to find RthR_{\text{th}}.
  7. Compute τ\tau and write:

x(t)=x(∞)+(x(0+)−x(∞))e−t/τx(t)=x(\infty)+\big(x(0^+)-x(\infty)\big)e^{-t/\tau}

B. Quick annotated mini-example (RC)

A source VsV_s is connected through RR to a capacitor CC at t=0t=0, with vC(0−)=0v_C(0^-)=0.

  • Final: vC(∞)=Vsv_C(\infty)=V_s (capacitor open, no drop across RR).
  • Rth=RR_{\text{th}}=R.
  • τ=RC\tau=RC.

So:

vC(t)=Vs(1−e−t/(RC))v_C(t)=V_s\big(1-e^{-t/(RC)}\big)

C. Quick annotated mini-example (RL)

A source VsV_s drives series RR and inductor LL at t=0t=0, with iL(0−)=0i_L(0^-)=0.

  • Final: iL(∞)=VsRi_L(\infty)=\frac{V_s}{R} (inductor short at DC).
  • Rth=RR_{\text{th}}=R.
  • τ=LR\tau=\frac{L}{R}.

So:

iL(t)=VsR(1−e−tR/L)i_L(t)=\frac{V_s}{R}\big(1-e^{-tR/L}\big)

3. Key Formulas, Rules & Facts

A. Time constant summary table
ItemFormulaWhen to useNotes
RC time constantτ=RthC\tau=R_{\text{th}}COne capacitor, rest is resistive + sourcesRthR_{\text{th}} seen by capacitor in post-switch circuit
RL time constantτ=LRth\tau=\frac{L}{R_{\text{th}}}One inductor, rest is resistive + sourcesRthR_{\text{th}} seen by inductor in post-switch circuit
General 1st-order formx(t)=x(∞)+(x(0+)−x(∞))e−t/τx(t)=x(\infty)+\big(x(0^+)-x(\infty)\big)e^{-t/\tau}Any first-order RC/RL transientWorks for rise/decay, any initial/final
Remaining error fractionx(t)−x(∞)x(0+)−x(∞)=e−t/τ\frac{x(t)-x(\infty)}{x(0^+)-x(\infty)}=e^{-t/\tau}Solving for time to reach toleranceVery exam-friendly
Time to reach fraction pp of changet=−τln⁡(1−p)t=-\tau\ln\big(1-p\big)“How long to reach 90%90\%?”Here pp is fraction of total change
Time to decay to fraction kkt=−τln⁡(k)t=-\tau\ln(k)“Decay to 10%10\% of initial”Here k=x(t)x(0+)k=\frac{x(t)}{x(0^+)} when final is zero
B. What counts as RthR_{\text{th}}?

To find RthR_{\text{th}} seen by the element terminals (post-switch):

  • Remove the capacitor (open its terminals) or remove the inductor (open its terminals).
  • Look into the network at those two terminals.
  • Turn off independent sources:
    • Voltage source →\rightarrow short circuit.
    • Current source →\rightarrow open circuit.
  • Keep dependent sources. If dependent sources exist:
    • Apply a test voltage VtV_t or test current ItI_t at the terminals.
    • Compute Rth=VtItR_{\text{th}}=\frac{V_t}{I_t}.

If the element is connected between a node and ground, RthR_{\text{th}} is often just the equivalent resistance from that node to ground with sources killed.

C. DC steady-state “end behavior” rules

At DC steady state (constant sources, long time):

  • Capacitor: iC(∞)=0i_C(\infty)=0 and it behaves as an open circuit.
  • Inductor: vL(∞)=0v_L(\infty)=0 and it behaves as a short circuit.
D. Continuity + element laws
  • Capacitor law:

iC(t)=C dvC(t)dti_C(t)=C\,\frac{dv_C(t)}{dt}

  • Inductor law:

vL(t)=L diL(t)dtv_L(t)=L\,\frac{di_L(t)}{dt}

Continuity at switching:

  • vC(0+)=vC(0−)v_C(0^+)=v_C(0^-)
  • iL(0+)=iL(0−)i_L(0^+)=i_L(0^-)
E. “Percent complete” landmarks (memorize)

Because e−1≈0.3679e^{-1}\approx 0.3679:

  • At t=τt=\tau: error is 36.8%36.8\% remaining, so you are 63.2%63.2\% to final.
  • At t=2τt=2\tau: error 13.5%13.5\%.
  • At t=3τt=3\tau: error 5.0%5.0\%.
  • At t=4τt=4\tau: error 1.8%1.8\%.
  • At t=5τt=5\tau: error 0.67%0.67\% (often treated as “settled”).
F. Common special-case forms (useful shortcuts)

RC charging (from 00 to VfV_f):

vC(t)=Vf(1−e−t/τ)v_C(t)=V_f\big(1-e^{-t/\tau}\big)

RC discharging (from V0V_0 to 00):

vC(t)=V0e−t/τv_C(t)=V_0e^{-t/\tau}

RL current rise (from 00 to IfI_f):

iL(t)=If(1−e−t/τ)i_L(t)=I_f\big(1-e^{-t/\tau}\big)

RL current decay (from I0I_0 to 00):

iL(t)=I0e−t/τi_L(t)=I_0e^{-t/\tau}

G. Units sanity checks
  • τ\tau is in seconds.
  • RC: Ω×F=s\Omega\times \text{F}=\text{s}.
  • RL: H/Ω=s\text{H}/\Omega=\text{s}.

4. Examples & Applications

Example 1: RC with a nontrivial RthR_{\text{th}} (voltage divider drive)

You have a capacitor from node vv to ground. Node vv is connected to a source VsV_s through R1R_1, and also to ground through R2R_2. At t=0t=0, the source is applied. Find τ\tau and vC(t)v_C(t) assuming vC(0−)=0v_C(0^-)=0.

Key insight: Replace the driving network by its Thevenin equivalent as seen by the capacitor.

  • Final node voltage (capacitor open at DC):

vC(∞)=VsR2R1+R2v_C(\infty)=V_s\frac{R_2}{R_1+R_2}

  • Thevenin resistance (source killed: ideal VsV_s shorted):

Rth=R1∥R2=R1R2R1+R2R_{\text{th}}=R_1\parallel R_2=\frac{R_1R_2}{R_1+R_2}

  • Time constant:

τ=(R1∥R2)C\tau=(R_1\parallel R_2)C

  • Response:

vC(t)=vC(∞)(1−e−t/τ)v_C(t)=v_C(\infty)\big(1-e^{-t/\tau}\big)

Example 2: RL decay after disconnecting the source

An inductor LL carries current I0I_0 just before t=0t=0. At t=0t=0 the source is disconnected, and the inductor is left in a loop with a resistor RR.

Key insight: Inductor current is continuous and must have a discharge path.

  • Initial: iL(0+)=I0i_L(0^+)=I_0.
  • Final: iL(∞)=0i_L(\infty)=0.
  • Resistance seen by inductor: Rth=RR_{\text{th}}=R.
  • Time constant:

τ=LR\tau=\frac{L}{R}

  • Current decay:

iL(t)=I0e−tR/Li_L(t)=I_0e^{-tR/L}

If they ask for inductor voltage (passive sign convention):

vL(t)=LdiL(t)dt=−RI0e−tR/Lv_L(t)=L\frac{di_L(t)}{dt}=-RI_0e^{-tR/L}

Example 3: Time-to-threshold (timing capacitor)

A capacitor charges toward VfV_f with time constant τ\tau from initial 00. How long until vC(t)=VTv_C(t)=V_T?

Start with:

vC(t)=Vf(1−e−t/τ)v_C(t)=V_f\big(1-e^{-t/\tau}\big)

Solve:

VT=Vf(1−e−t/τ)V_T=V_f\big(1-e^{-t/\tau}\big)

e−t/τ=1−VTVfe^{-t/\tau}=1-\frac{V_T}{V_f}

t=−τln⁡(1−VTVf)t=-\tau\ln\Big(1-\frac{V_T}{V_f}\Big)

Exam pattern: Plug numbers carefully; check that 0<VT<Vf0<V_T<V_f so the log argument stays positive.

Example 4: RL with multiple resistors (finding RthR_{\text{th}})

An inductor is connected between node aa and ground. From node aa to a source node is R1R_1, and from node aa to ground is R2R_2. After switching, the source is set to 00 (ideal voltage source becomes a short).

Key insight: With sources killed, the inductor sees the equivalent resistance from node aa to ground.

Rth=R1∥R2R_{\text{th}}=R_1\parallel R_2

So:

τ=LR1∥R2\tau=\frac{L}{R_1\parallel R_2}

If the post-switch final DC makes the inductor a short, compute iL(∞)i_L(\infty) from the post-switch resistive network with that short in place.

5. Common Mistakes & Traps

  1. Using vC(0+)=0v_C(0^+)=0 or iL(0+)=0i_L(0^+)=0 by default

    • Wrong because the stored energy may be nonzero.
    • Fix: always find vC(0−)v_C(0^-) or iL(0−)i_L(0^-) from the pre-switch steady state, then apply continuity.
  2. Flipping the continuity rules

    • Students mix “capacitor current continuous” or “inductor voltage continuous.”
    • Correct: vCv_C is continuous, iLi_L is continuous.
  3. Computing RR incorrectly for τ\tau (not using RthR_{\text{th}})

    • Using “the resistor next to it” fails when there are multiple resistors/sources.
    • Fix: remove the element, kill independent sources, and find the equivalent resistance seen at its terminals.
  4. Turning off dependent sources

    • Wrong: dependent sources stay active, so killing them changes the resistance.
    • Fix: keep dependent sources and use a test source to find RthR_{\text{th}}.
  5. Using pre-switch RthR_{\text{th}} instead of post-switch RthR_{\text{th}}

    • τ\tau is determined by the circuit configuration for t>0t>0.
    • Fix: compute RthR_{\text{th}} from the post-switch circuit.
  6. Sign mistakes in the exponential

    • The exponential must decay: e−t/τe^{-t/\tau}, not e+t/τe^{+t/\tau}.
    • Quick check: as t→∞t\rightarrow\infty, the exponential term should go to 00.
  7. Confusing “percent of final” vs “percent error remaining”

    • At t=τt=\tau, you are at 63.2%63.2\% of the change, not “down to 63.2%63.2\%.”
    • Fix: remember e−1=0.368e^{-1}=0.368 is the remaining error fraction.
  8. Applying single-time-constant formulas to higher-order circuits

    • If there is more than one energy storage element (e.g., two capacitors), response is not single-exponential in general.
    • Fix: verify “only one CC or one LL” before using τ\tau shortcuts.

6. Memory Aids & Quick Tricks

Trick / mnemonicWhat it helps you rememberWhen to use
“C holds V, L holds I”vCv_C continuous, iLi_L continuousAny switching transient
“Kill sources, look in”How to find RthR_{\text{th}} for τ\tauComputing time constant
“RC: multiply, RL: divide”τ=RthC\tau=R_{\text{th}}C and τ=LRth\tau=\frac{L}{R_{\text{th}}}Fast recall
“1 tau = 63\% there”Landmark for exponential progressEstimation and sanity checks
“5 tau = settled”Approx steady state (error <1%<1\%)Timing approximations
“Final is DC steady state”Capacitor open, inductor short at t→∞t\rightarrow\inftyFinding x(∞)x(\infty)

7. Quick Review Checklist

  • [ ] Confirm it’s first-order: exactly one CC or one LL.
  • [ ] Use DC steady-state equivalents to find pre-switch value: capacitor open, inductor short.
  • [ ] Apply continuity: vC(0+)=vC(0−)v_C(0^+)=v_C(0^-), iL(0+)=iL(0−)i_L(0^+)=i_L(0^-).
  • [ ] Find post-switch final value with DC steady state.
  • [ ] Compute RthR_{\text{th}} seen by the element in the post-switch circuit (kill independent sources only).
  • [ ] Compute τ\tau: τ=RthC\tau=R_{\text{th}}C or τ=LRth\tau=\frac{L}{R_{\text{th}}}.
  • [ ] Write the solution in the universal form:

x(t)=x(∞)+(x(0+)−x(∞))e−t/τx(t)=x(\infty)+\big(x(0^+)-x(\infty)\big)e^{-t/\tau}

  • [ ] Sanity check: at t=0t=0 you get x(0+)x(0^+); as t→∞t\rightarrow\infty you get x(∞)x(\infty); exponential decays.

You’ve got this: if you can consistently find x(0+)x(0^+), x(∞)x(\infty), and τ\tau, you can do almost every RC/RL transient problem fast.