CDL Pre-Trip Picture Study Guide

Engine Compartment Inspection

  • Ground Leaks Check:
    • Inspect directly beneath the engine and undercarriage for puddles, drips, or active leaks of oil, coolant, or fuel.
    • Identify the source of any fluid accumulation prior to operating the vehicle.

Checking for ground leaks under the truck front

  • Axle Seal and Hub Seal:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Verify that it is not leaking around the hub cap or axle flange.
    • Must be filled to manufacturer specifications with oil level verified through sight glass or fill plug.

Wheel hub seal and axle cap inspection point

  • Belt-Driven Alternator:
    • Must be properly mounted and secured with no loose or missing mounting bolts.
    • Must not be cracked, bent, or broken.
    • Ensure all electrical wires are firmly connected with no frayed insulation or corrosion.
    • The alternator drive belt must not be cracked, worn, or frayed.
    • Belt free play (deflection) must be between 12 inch\frac{1}{2}\text{ inch} and 34 inch\frac{3}{4}\text{ inch} at the center of the belt span.

Alternator and drive belt inspection area

  • Belt-Driven Water Pump:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must not be leaking coolant from the pump housing or weep hole.
    • Drive belt must not be cracked or frayed, with allowable belt free play between 12 inch\frac{1}{2}\text{ inch} and 34 inch\frac{3}{4}\text{ inch}.

Water pump location indicated in the engine compartment

  • Engine Oil Level:
    • Check with the engine off.
    • Remove dipstick, wipe clean, re-insert fully, and pull again to verify the oil level is within the cross-hatch operating range and filled to manufacturer specifications.

Oil level dipstick location indicated by arrow

  • Coolant Reservoir:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must not be leaking coolant from reservoir, fittings, or cap.
    • Fluid level must be filled to manufacturer specifications (visible between minimum and maximum marks).

Coolant reservoir mounted in engine compartment

  • Power Steering Fluid Reservoir:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must not be leaking fluid.
    • Must be filled to manufacturer specifications (checked via dipstick or external reservoir sight level).

Power steering fluid reservoir

  • Gear-Driven Air Compressor:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must not be leaking air, oil, or coolant.
    • Must be identified as gear-driven (no drive belts attached).

Gear-driven air compressor on engine block

  • Gear-Driven Power Steering Pump:
    • Must be properly mounted and secured to the engine housing.
    • Must not be cracked, bent, or broken.
    • Must not be leaking hydraulic fluid.
    • Must be identified as gear-driven.

Power steering pump and lines

  • General Engine Hoses (Passenger Side):

    • All air, fluid, and coolant hoses must be properly mounted and secured at both ends with appropriate clamps or fittings.
    • Must show no abrasions, bulges, or cuts (ABC\text{ABC} criteria).
    • Must not be leaking fluid or air.
  • General Engine Hoses (Driver Side):

    • Must be properly mounted and secured at both ends.
    • Must have no abrasions, bulges, or cuts.
    • Must not be leaking fluid or air.

Steering System Inspection

  • Steering Gear Box and Hoses:
    • The steering box must be properly mounted and secured to the frame rail with no missing bolts.
    • Must not be cracked, bent, or broken.
    • Power steering pressure and return hoses must show no abrasions, bulges, or cuts.
    • Must not be leaking power steering fluid from the box or fittings.

Steering gear box and hydraulic hoses

  • Steering Column (Shaft):
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Universal joints must not have excessive play and must be free of binding or foreign debris.

Steering column shaft

  • Steering Linkage Overview:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Ensure there are no missing castle nuts or cotter pins.
    • Physical identification protocol: Specifically point out the pitman arm, the drag link, the tie rod, and all 33 castle nuts and cotter pins during inspection.

Steering linkage components including pitman arm, drag link, and tie rod

  • Pitman Arm:

    • Must be properly mounted and secured to the steering gear output shaft.
    • Must not be cracked, bent, or broken.
  • Drag Link:

    • Must be properly mounted and secured connecting the pitman arm to the upper steering knuckle.
    • Must not be cracked, bent, or broken.
  • Tie Rod:

    • Must be properly mounted and secured extending between the left and right steering knuckles.
    • Must not be cracked, bent, or broken.
  • Castle Nuts and Cotter Pins:

    • All 33 castle nuts must be present, tightly fastened, and secured with cotter pins.
    • None missing, damaged, or substituted.

Suspension System Inspection

  • Spring Hangers and Mounts:

    • Both front and rear spring hangers/brackets must be properly mounted and secured to the vehicle frame.
    • Must not be cracked, bent, or broken.
    • Check for missing or sheared mounting bolts and bushings.
  • Leaf Springs:

    • Must be properly mounted and secured at both ends within the spring hangers.
    • Must not be cracked, bent, or broken.
    • No leaf spring in the pack may be shifted, scissored, or missing.

Leaf spring suspension assembly

  • U-Bolts:
    • Must be properly mounted and secured around the axle and leaf spring pack.
    • Must not be cracked, bent, or broken.
    • None missing; all retaining nuts present and tight with no evidence of looseness.

Suspension U-bolts securing leaf spring assembly

  • Shock Absorbers:
    • Must be properly mounted and secured at both the top and bottom mounting brackets.
    • Must not be cracked, bent, or broken.
    • Must not be leaking hydraulic fluid from the body or seals.

Shock absorber mounted to suspension

  • Spring Mount:

    • Must be properly mounted and secured at both ends.
    • Must not be cracked, bent, or broken.
  • Spring Arm:

    • Must be properly mounted and secured at both ends.
    • Must not be cracked, bent, or broken.
  • Torque Arm:

    • Must be properly mounted and secured to axle and chassis.
    • Must not be cracked, bent, or broken.
  • Air Suspension Bag:

    • Must be properly mounted and secured at both top and bottom mounting plates.
    • Must not be cracked, bent, or broken.
    • Rubber bag must have no abrasions, bulges, or cuts.
    • Must not be leaking air.
    • Ensure there are no missing mounting bolts or loose mounting hardware.

Air suspension bag

Brake Components Inspection

  • Brake Hose (Air Line):
    • Must be properly mounted and secured at both ends.
    • Must show no abrasions, bulges, or cuts.
    • Must not be leaking air.

Brake hose line

  • Brake Chamber:
    • Must be properly mounted and secured to the mounting bracket with chamber clamp tight.
    • Must not be cracked, bent, or broken.
    • Must not be leaking air.

Brake chamber mounted on axle

  • Slack Adjuster and Push Rod:
    • Must be properly mounted and secured with clevis pin and cotter key in place.
    • Must not be cracked, bent, or broken.
    • Testing procedure: With the parking/emergency brakes released, pull the push rod firmly by hand; the push rod should not move more than 1 inch1\text{ inch}.

Slack adjuster and push rod connection

  • Brake Drum:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Inner friction surface must be free of deep grooves, heat cracks, or signs of overheating.

Brake drum and wheel assembly

  • Brake Linings (Shoes):
    • Must be properly mounted and secured to the brake shoes.
    • Must not be cracked, bent, or broken.
    • Must be free of contaminating oil, grease, and debris.
    • Friction material must not be worn dangerously thin.

Wheels, Tires, and Chassis Components

  • Steer Tires (Front Axle):
    • Must have no abrasions, bulges, or cuts to the tread surface or sidewalls.
    • Tread depth must be at least 432 inch\frac{4}{32}\text{ inch} across all major grooves.
    • Must be properly inflated to manufacturer specifications; verify inflation using an air pressure gauge (never recapped or regrooved on steer axles).

Steer tire tread and sidewall

  • Drive Tires (Tractor Tandem Axles):

    • Must show no abrasions, bulges, or cuts to the tread or sidewalls.
    • Tread depth must be at least 232 inch\frac{2}{32}\text{ inch}.
    • Must be inflated to manufacturer specifications; check with an air pressure gauge.
  • Trailer Tires:

    • Must have no abrasions, bulges, or cuts to the tread or sidewalls.
    • Tread depth must be at least 232 inch\frac{2}{32}\text{ inch}.
    • Must be inflated to manufacturer specifications; check with an air pressure gauge.
  • Wheel Rims:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must show no unauthorized welds or structural repairs.
  • Lug Nuts:

    • All lug nuts must be present, properly mounted, and secured.
    • Must not be cracked, bent, or broken.
    • Check for signs of looseness, such as rust trails extending from nuts on steel wheels or white powder residue on aluminum wheels.
    • Ensure there are no cracks radiating outward from bolt holes.

Wheel hub with lug nuts

  • Mudflaps (Splash Guards):

    • Must be properly mounted and secured to the brackets.
    • Must not be cracked, bent, torn, or broken, and must hang at the proper legal height.
  • Dual Tire Spacing:

    • If equipped with dual wheels, verify proper, even spacing between the inner and outer tires.
    • Confirm that there is no debris, rocks, or foreign objects wedged between them, and tires do not contact each other.

Spacing between dual tires

  • Exterior Mirrors:

    • Must be properly mounted and secured to the cab frame.
    • Must not be cracked, bent, or broken.
    • Mirror glass must be clean and unobstructed.
  • Cab Doors and Hinges:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must open, close, and latch securely from both inside and outside.
    • Rubber door weather-stripping seals must not be worn, torn, or dry-rotted.
  • Rear Cargo Doors and Hinges (Trailer):

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must open, close, and latch securely; locking rods and hasps functional.
    • Door seals must not be worn, torn, or dry-rotted.
  • Fuel Tank and Cap:

    • Fuel tank and mounting straps must be properly mounted and secured with rubber isolators intact.
    • Must not be cracked, bent, or broken.
    • No fuel leaks from the tank body, fuel lines, or filler neck.
    • Filler cap must be on tight with gasket intact.

Fuel tank and filler cap

  • Exhaust System:

    • Must be properly mounted and secured with all clamps tight.
    • Must not be cracked, bent, or broken.
    • Must show no signs of exhaust leaks, such as dark carbon soot stains around joints.
  • Drive Shaft:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, broken, or twisted.
    • Universal joints (U-joints\text{U-joints}) and carrier bearings must be secure and free of foreign debris.
  • Catwalk and Tractor Access Steps:

    • Must be properly mounted and secured to the frame.
    • Must not be cracked, bent, or broken.
    • Must be completely clean and clear of loose objects, tools, oil, ice, or debris.

Catwalk and tractor access steps

  • Frame and Cross Members:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must show no unauthorized holes drilled or unauthorized structural welds.
    • Ensure there are no missing cross members.

Coupling System and Trailer Connections

  • Electric Line (Pigtail):
    • Must be properly mounted and secured at both the tractor and trailer receptacle connections.
    • Must show no abrasions, bulges, or cuts along the jacket.
    • Safety locking latches must be engaged, with no bare or exposed electrical wires.

Electric line trailer connection

  • Air Lines (Emergency/Red and Service/Blue):

    • Must be properly mounted and secured at both tractor and trailer connections.
    • Must show no abrasions, bulges, or cuts.
    • Must not be leaking air, spliced, or dragging against the catwalk.
  • Glad Hands:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Rubber grommets/seals must be in good condition, soft and pliable, without cracks, dry rot, or splits.
    • Must lock firmly in position with no audible air leaks.

Glad hand air couplers

  • Trailer Apron:
    • Must be properly mounted and secured to the base of the trailer.
    • Must not be cracked, bent, or broken.

Trailer apron

  • Fifth Wheel Skid Plate:
    • Must be properly mounted and secured to the mounting base.
    • Must not be cracked, bent, or broken.
    • Surface must be properly lubricated with grease.

Fifth wheel skid plate

  • Apron-to-Skid Plate Interface:
    • Visual check: Ensure there is zero visible gap between the trailer apron and the fifth wheel skid plate when coupled.

Interface between trailer apron and fifth wheel skid plate

  • Kingpin:
    • Must be properly mounted and secured under the trailer.
    • Must not be cracked, bent, or broken.

Trailer kingpin

  • Locking Jaws:
    • Must be properly mounted and secured within the fifth wheel throat.
    • Must not be cracked, bent, or broken.
    • Must be fully closed and locked around the shank of the kingpin.

Fifth wheel locking jaws

  • Fifth Wheel Platform:

    • Must be properly mounted and secured to the tractor frame.
    • Must not be cracked, bent, or broken.
  • Mounting Bolts:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • None missing; all hardware tight.
  • Release Arm and Safety Latch:

    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Must be seated in the fully locked position.

Fifth wheel release arm

  • Sliding Fifth Wheel and Locking Pins:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Pins must be fully engaged in the slide rack; slide mechanism in the locked position.

Sliding fifth wheel mechanism and locking pins

  • Tractor-to-Trailer Clearance:

    • Verify sufficient operating clearance between the tractor frame/mudflaps and trailer landing gear to prevent contact during sharp turns.
  • Trailer Header Board (Bulkhead):

    • Must be properly mounted and secured to the front of the trailer.
    • Must not be cracked, bent, or broken.
    • Must have no missing rivets, structural tears, or holes capable of letting cargo shift forward.
  • Landing Gear:

    • Must be properly mounted and secured with braces intact.
    • Must not be cracked, bent, or broken.
    • Legs and foot pads must be fully raised.
    • Crank handle must be securely stowed in its bracket.

Trailer landing gear support legs and crank handle

  • Trailer Tandem Frame and Release:
    • Must be properly mounted and secured.
    • Must not be cracked, bent, or broken.
    • Tandem slide pins must be fully locked through the rail holes, and release handle stowed in locked position.

Trailer tandem frame sliding pins and release

Vehicle Lighting and In-Cab Inspections

  • Five Locations for Light Checks:

    • 1.1. Front of truck.
    • 2.2. Both sides of truck.
    • 3.3. Rear of truck.
    • 4.4. Both sides of trailer.
    • 5.5. Rear of trailer.
  • Five Lighting Functions to Verify:

    • 1.1. Left turn signal.
    • 2.2. Right turn signal.
    • 3.3. Four-way emergency flashers.
    • 4.4. High and low beam headlights.
    • 5.5. Brake lights.
  • Light, Reflector, and Reflective Tape Standards:

    • Check all exterior lights, reflectors, and retro-reflective tape.
    • Must be properly mounted and secured; not cracked, bent, or broken.
    • Clean, fully illuminated, and displaying proper colors:
      • Amber on the front and sides of the vehicle.
      • Red on the rear of the vehicle.
  • Driver Seat Belt:

    • Must be properly mounted and secured to the cab floor and B-pillar.
    • Webbing must not be ripped, torn, or frayed.
    • Must adjust smoothly, latch securely, and release properly.
  • Emergency Safety Equipment:

    • Fire extinguisher: Must be properly mounted, secured, fully charged (indicator needle in green), with pin intact.
    • Three red reflective emergency triangles: Present and undamaged.
    • Spare electrical fuses: Spare fuses present for all critical circuits (if required by vehicle electrical design).
    • Know and confirm the exact storage locations in the cab.
  • Safe Start Procedure:

    • Ensure the parking brake is set.
    • Verify the transmission is in neutral (fully depress clutch pedal if equipped with manual transmission).
    • Turn ignition switch key on.
    • Verify anti-lock braking system (ABS\text{ABS}) dashboard light illuminates and then turns off.
    • Start the engine.
  • Primary Instrument Gauges:

    • Voltmeter: Verifies alternator is operating and charging in the normal range between 13 volts13\text{ volts} and 14 volts14\text{ volts}.
    • Oil Pressure Gauge: Confirms oil pressure rises to normal operating range shortly after starting.
    • Water Temperature Gauge: Confirms engine coolant temperature climbs steadily toward normal operating range.
    • Air Pressure Gauges: Confirm primary and secondary air tanks build pressure to governor cut-out.
  • Horns:

    • Test and sound both the electric city horn and the pneumatic air horn to confirm operational readiness.
  • Windshield and Mirrors:

    • Windshield must be clean, with no illegal stickers, cracks, breaks, or visual obstructions.
    • Mirrors must be clean and properly adjusted to the driver's seating position.
  • Windshield Wipers and Washers:

    • Operate washer spray control to demonstrate adequate fluid flow.
    • Wipers must be mounted securely, wipe smoothly with even tension, and rubber wiper blades must not be cracked, torn, or dry-rotted.
  • Heater and Defroster:

    • Turn on climate controls to demonstrate that both the cab heater and the windshield defroster blow air correctly.
  • Dashboard Lighting Indicators:

    • Activate and verify the corresponding internal dashboard indicator lights for:
      • Left turn signal.
      • Right turn signal.
      • Four-way hazard flashers.
      • High beam headlight indicator.

Brake System Operational Checks and Formal Announcements

  • Tractor and Trailer Parking Brake Check:

    • Step 11 (Trailer Brake Test): Set the trailer parking brake (red knob pulled out) and release the tractor parking brake (yellow knob pushed in). Put transmission in gear and gently tug forward against the trailer brake to verify it holds.
    • Step 22 (Tractor Brake Test): Set the tractor parking brake (yellow knob out) and release the trailer parking brake (red knob in). Put transmission in gear and gently tug forward against the tractor brake to verify it holds.
    • Verbatim Parking Brake Check Announcement:
      • "My tractor and trailer parking brake test was successful. I will now do my service brake check."
  • Service Brake Operational Check:

    • Release both tractor and trailer parking brakes (both knobs pushed in).
    • Drive the vehicle forward at idle speed (approximately 5 mph5\text{ mph}).
    • Firmly apply the foot service brake pedal.
    • Vehicle must come to a complete, smooth stop without grabbing, unusual delay, or pulling to the left or right.
    • Verbatim Service Brake Announcement:
      • "My service brake check was successful; the vehicle came to a safe stop and did not pull left or right."
  • Three Stages of an Air Brake Test:

    • Stage 11: Applied pressure leakage test.
    • Stage 22: Low-air warning light and buzzer test.
    • Stage 33: Tractor/trailer protection valve pop-out test.
  • Applied Pressure Leakage Test Procedure:

    • Run engine to build system air pressure until the air compressor governor cuts out.
    • Turn the engine completely off, then turn the ignition key back to the "on"/accessory position so gauges and warning indicators remain energized.
    • Push in both parking brake control valves (releasing tractor and trailer brakes).
    • Fully depress and hold the foot brake pedal down.
    • Allow the air pressure gauges to stabilize.
    • Time for 1 full minute1\text{ full minute}. In a Class A tractor-trailer combination, air loss must not exceed 4 PSI4\text{ PSI} in one minute.
    • Listen intently for any audible air leaks during the minute.
    • Verbatim Applied Pressure Test Announcement:
      • "This test was successful because I did not lose more than 4 PSI in this tractor-trailer combination vehicle."
  • Low-Air Warning Light and Buzzer Test Procedure:

    • With ignition remaining on, repeatedly pump (fan) the foot brake pedal down and up to drain air pressure from the primary and secondary tanks.
    • Observe gauges and verify that the low-air warning light and buzzer activate at or before system pressure falls to 60 PSI60\text{ PSI}.
    • Verbally announce the successful activation of the visual light and audible buzzer.
  • Tractor/Trailer Protection Valve Pop-Out Test Procedure:

    • Continue pumping the foot brake pedal to rapidly exhaust additional system air pressure.
    • Monitor the red (trailer) and yellow (tractor) dash valves.
    • Verify that both parking brake/emergency protection valves pop out into the emergency set position (typically between 40 PSI40\text{ PSI} and 20 PSI20\text{ PSI}, confirmed against vehicle-specific operational thresholds).
  • CDL Inspection Study Note:

    • All inspection wording, test thresholds, and procedures reproduce the exact criteria required for the commercial pre-trip examination and should be cross-referenced against your state CDL manual and specific vehicle equipment configurations.