Practicals

Practical 4: Bloods Training

Capillary blood sampling refers to sampling blood from a puncture on the finger, heel or earlobe.

  • It is a common procedure used by SES physiologists.


Advantages of capillary blood sampling over venous blood sampling

  1. Less invasive

  2. Requires smaller amounts of blood

  3. Can be performed quickly and easily*

*obtaining blood via skin puncture instead of venepuncture can be especially useful for athletes as it can be readily done in the field as well as laboratory.


If capillary blood sampling is carried out incorrectly, it can cause

  • Inaccurate test results

  • Pain

  • Tissue damage

Additionally, the small volumes involved, & the variability in sample quality based on puncture site and technique make capillary sampling particularly susceptible to pre-analytical errors.

  • SES physiologists must adhere to strict and standardised blood sampling techniques to ensure accurate and consistent results.


Lactate measurements

  • Good indicator of adaptations to training

  • They correlate well with endurance performance

  • They are often used as a way of identifying optimal training zones for athletes.


Measuring blood glucose levels before & after feeding (pre- and post prandial) has been used in exercise science to understand the effects of CHOs on metabolism and exercise performance.

  • In a clinical setting a blood glucose test is used to find out if blood sugar levels are within a healthy range.

  • Hyperglycaemia may be a sign of diabetes.

  • Hypoglycaemia can lead to major health problems, including brain damage, if not treated.


Common pre-analytical errors in capillary blood sampling

Correct choice of lancet

  • The lancet must make a sufficiently deep puncture to ensure adequate flow of blood.

  • 1.85mm-2.25mm is recommended for adults!


Correct selection of puncture site

  • Use middle or ring finger (since they’re generally less calloused & less sensitive to pain compared to the index finger or thumb)

  • Ideally on non-dominant hand.

  • Thumb should be avoided due to its pulse (arterial presence).

  • Pinky finger - distance between the skin surface and bone is too small.

  • The puncture should be made slightly off centre from the central, fleshy portion of the fingertip (near the side where the skin is thinner with were nerve endings and less pain sensation).


Cleaning, disinfection, & drying

  • Cleaning & disinfection of the puncture site’s essential to remove any potential contaminants that could affect the reading or jeopardise participant safety.

  • Puncture site must be dried completely after cleaning to remove any remnants of alcohol solution that’ll dilute the blood sample and cause false readings.


Applying too much pressure around the puncture site

  • Finger can be gently massaged before/after the puncture to stimulate blood circulation.

  • Don’t go past the 1st knuckle when massaging.

  • Maintaining a light pressure at the moment of puncture ensures effective penetration.

  • Finger should not be pressed too hard as this will push fluid from the tissue into the blood, & cause false low readings.


During capillary collection, if an investigator presses hard around the puncture site to express blood into a collection tube, the specific analytic error and physiological mechanism induced is that it will force tissue fluid into the blood, resulting in false low readings.

Very important that you wipe away the first 2-3 drops of blood, and make sure there is a free blood flow before filling the capillary tube.


It is important to press the lancet firmly against the incision site before dispensing the needle

  • To reduce the chance of the needle slipping - this makes the process safer

  • To ensure the incision is deep enough - allows us to collect the sample in a timely manner. If an incision is too shallow, blood flow may be slow and can stop before the sample is collected.

  • To leave an imprint on the incision site; this allows us to identify where the incision will be made.


TOP TIP

Wipe the finger between drawing the sample into the capillary tube so there is a big blood droplet - this makes it easier for the capillary tube to draw up the sample.

Also, hold the collection tube parallel with the ground to avoid getting an air bubble in the tube.


You need to fill the capillary tube entirely, as not filling it could affect analysis.

Sharps Bin

  • Used to dispose of sharp objects

  • Place used lancets straight into this bin.


Haemolysis Cups (the clear things in the orange tray)

  • They contain an anti-coagulant

  • They are used for the storage & analysis of the sample. Place the full capillary tube into an Eppendorf and complete 6-8 inversions to mix thoroughly.

  • Invert rather than shaking the tube, as shaking the tube will create air bubbles that may affect analysis.


Lancets (orange things on the grey tray)

  • Lancets contain a needle

  • Used to create the incision from which you collect a capillary blood sample.


Tissues

  • Used to wipe the excess blood.


Alcohol Wipe

  • Used to clean the incision site.

  • They reduce the risk of infection.

  • Clean multiple sites at once if taking more than 1 sample throughout the protocol.


Capillary Tubes

  • Shown below the alcohol wipes

  • 20uL capillary tubes are used to collect the blood sample.


Clinical Waste Bin/Bag

  • Located on the left of the sharps bin.

  • Dispose of contaminated soft waste in this bin, e.g. used gloves, alcohol wipes, & tissues.


Gloves

  • Shown underneath the top station.

  • Wear gloves throughout the blood sampling process.

  • Before starting, wash your hands thoroughly.

  • Gloves protect us from spillages and direct contact with blood.


SUMMARISED STEP-BY-STEP PROCEDURE

  1. Clean the site with an alcohol wipe

  2. Twist the lancet cap to remove

  3. Make an incision

  4. Wipe away first blood droplet

  5. Fill capillary tube with blood

  6. Place full capillary tube into haemolysing cup

  7. Invert haemolysing cup to mix sample


BLOOD SAMPLE ANALYSIS

Capillary blood samples can be used to determine

  • Blood lactate & glucose concentrations

  • Haematocrit

  • Haemoglobin concentration

  • Blood gas data (pH, pCO2, pO2, electrolyte concentrations etc).


Different analysis techniques require different blood sample collection vessels. Below are 4 sample collection vessels commonly used within the lab

  1. Carefull Capillary Tube

  • Used to collect a blood sample analysis using an EPOC machine.

  • Requires approx 90uL of blood to fill it.


  1. 80uL Capillary Tube

  • Used for the analysis of haematocrit.

  • The sample takes longer to collect due to the increases volume, so ensure there is a deep enough incision.


  1. 20uL Capillary Tube

  • Used to collect a blood sample for analysis of blood lactate & glucose concentrations using a Biosen C-line analyser.

  • The sample is collected and placed in a pre-filled haemolysing cup before being inverted & analysed.

  • These tubes are the most commonly used within the lab for collecting and analysing capillary blood samples.

—> Capillary tubes are named this because it uses capillary action to draw blood into the tube; blood adheres to the inner wall of the tube, generating a force that draws additional blood into the tube without the need for external suction.


  1. Microcuvette

  • Used to analyse Hb concentration from a capillary blood sample.

  • A single large blood droplet is all that is required for the analysis.


The biosen C-line is used to analyse capillary blood lactate and glucose concentrations. The machine needs to be calibrated prior to use and can analyse 20 samples in a single run. Only 20uL capillary tubes can be used in this machine.