Comprehensive Introduction to Nuclear Medicine and ALARA and Instrumentation

Fundamental Imaging Parameters and Terminology

  • Resolution Definitions

    • Spatial Resolution: Defined as the ability of the camera to distinguish between adjacent points in an organ. In quantitative terms, it is measured by Full Width at Half Maximum (FWHMFWHM), where a smaller value indicates superior resolution.
    • Energy Resolution: The ability of the camera system to distinguish between pulses of different energies, allowing for the discrimination of photon energies.
    • Temporal Resolution: Refers to the minimum time required for the acquisition of counts.
  • Sensitivity

    • Definition: The ability of the camera to detect photons emitted by the radiopharmaceutical.
      • Low Sensitivity: The system detects only a small fraction of the generated photons.
      • High Sensitivity: The system detects a higher fraction of the generated photons. This is physically achieved by using a smaller number of larger holes separated by thin septa in the collimator.
    • The Sensitivity-Resolution Trade-off: There is a constant trade-off between these two parameters. Greater sensitivity (accepting more counts/photons) results in decreased spatial resolution because the collimator permits a wider path for photons to enter.
  • Digital Matrix and Acquisition Stop Conditions

    • Matrices: Nuclear medicine images use a digital grid ranging from 64×6464 \times 64 to 256×256256 \times 256.
      • A larger matrix improves image resolution.
      • However, larger matrices require more counts or increased acquisition time to maintain image quality.
    • Stop Conditions: Scans are terminated based on specific criteria:
      • Time: Used primarily for dynamic and SPECT scans.
      • Counts: Used primarily for static scans.

Common Nuclear Medicine Isotopes

  • 99mTc^{99m}Tc (Technetium-99m): Characterized as a low-energy isotope; it is the most widely used isotope in nuclear medicine.
  • I−131I-131 (Iodine-131): Characterized as a high-energy isotope.
  • I−123I-123 (Iodine-123): Characterized as a medium-energy isotope.
  • Ga−67Ga-67 (Gallium-67): Characterized as a medium-energy isotope.
  • Tl−201Tl-201 (Thallium-201): Characterized as a low-energy isotope.

Instrumentation and Components of the Gamma Camera

  • System Components and Signal Flow
    • Collimator: Defines the photon path by allowing only photons traveling in specific directions to reach the crystal.
    • →\rightarrow NaI Scintillation Crystal: Converts the high-energy γ\gamma (gamma) photons into visible light photons (scintillation).
    • →\rightarrow Photomultiplier Tubes (PMTs): Convert the visible light into an electronic signal.
    • →\rightarrow Pulse Height Analyser (PHA): Determines the energy and spatial location of the event to create the final image.

Quality Control (QC) Procedures

  • Purpose of Quality Control: Inspecting equipment to ensure that all aspects of performance are satisfactory and strictly adhere to defined performance criteria.

  • Gamma Camera QC

    • Daily Checks:
      • Visual Safety: Checking for physical hazards or equipment integrity.
      • Background: Monitoring ambient radiation levels.
      • Photopeak: Aligning the energy window of the camera to the specific isotope being used.
      • Uniformity Flood: Performed to detect any issues with the PMTs or the scintillation crystal.
        • Intrinsic Flood: Performed without the collimator using a point source.
        • Extrinsic Flood: Performed with the collimator on using a sheet source.
    • Monthly Checks:
      • Centre of Rotation (COR): Essential for maintain SPECT image alignment.
      • Spatial Linearity and Resolution: Evaluated using Bar phantoms.
  • Dose Calibrator QC

    • Constancy: Performed daily using a long-lived source; the result must be within ±10%\pm 10\%.
    • Linearity: Performed quarterly or annually; involves measuring the decay of a high-activity source of 99mTc^{99m}Tc over time.
    • Accuracy: Performed annually using a traceable standard source.
    • Geometry: Performed at installation to account for volume changes in the source; the result must be within ±2%\pm 2\%.

Radiation Safety and ALARA Principles

  • The Three Pillars of Protection

    • Time: Minimise the time spent in proximity to the radiation source.
    • Distance: Based on the Inverse Square Law (1/d21/d^2), increasing distance significantly reduces exposure.
    • Protection/Shielding:
      • Lead (PbPb): Used for shielding γ\gamma (gamma) radiation.
      • Perspex or Plastic: Used for shielding β\beta (beta) radiation to avoid the production of secondary Bremsstrahlung radiation.
  • Monitoring and Maintenance

    • Monitoring: Personnel wear Luxel badges made of Aluminum oxide to measure exposure to X-rays, γ\gamma, and β\beta radiation.
    • Waste Management:
      • Solid Waste: Stored until the activity decays to background levels.
      • Liquid Waste: Disposed of via designated sewerage sinks.
    • Spill Management: Always perform personal decontamination first. When cleaning, wipe from the outside inward to avoid spreading the contamination.

Positioning, Imaging Modes, and Review Methodology

  • Imaging Views

    • ANT: Anterior view.
    • POST: Posterior view.
    • OBL: Oblique views (e.g., Right Anterior Oblique RAO, Left Posterior Oblique LPO).
    • Lateral: Side views.
  • Imaging Modes

    • Static: A single image taken from a fixed point.
    • Dynamic/Flow: Multiple frames acquired sequentially over time (e.g., for blood flow).
    • SPECT: Three-dimensional reconstruction generated from the camera rotating around the patient.
    • Whole Body: A head-to-toe scan.
  • Uptake Terminology

    • Photopenic/Cold: Areas of decreased radiopharmaceutical uptake.
    • Intense/Hot: Areas of increased radiopharmaceutical uptake.
    • Focal: Localised uptake in a specific area.
    • Diffuse: Uptake spread throughout an organ or region.
  • Image Review Method

    1. Evaluate patient history.
    2. Review the order of acquisition.
    3. Identify normal versus abnormal uptake.
    4. Formulate a diagnostic comment.

Clinical Workflow and Communication

  • Personnel Chain: Reception →\rightarrow Nuclear Medicine Technologist →\rightarrow Physician.
  • Informed Consent: Effective communication is vital for obtaining informed consent and reducing patient anxiety, specifically regarding potential time delays in the procedure.