Comprehensive Study Guide on Horizontal Structural Systems and Prestressing
Nomenclature and Functional Role of Horizontal Subsystems
Within the structural framework of a building, the horizontal components of horizontal subsystems are identified by several common names depending on their specific role and scale. These include beams (vigas), girders or beams (trabes), joists (viguetas), and master beams (vigas maestras). These linear horizontal components fulfill the critical function of supporting vertical loads transversally along the element. This action generates internal forces, specifically shear forces and bending moments, which the element must resist to maintain stability.
To achieve a more exact dimensioning of these components, it is not sufficient to simply base the design on the general structure; rather, it is necessary to calculate the maximum bending moment or the controlling moment of the specific component. Furthermore, when these horizontal layers or components flex, they must resist sliding actions between them. If there is no structural interaction between the component strips, they will behave as independent beams with very little depth, which significantly reduces their load-bearing efficiency.
Structural Analysis: Bending, Shear, and Moments
Bending moments produced by loads acting on a beam must be resisted by an internal resistive couple within that beam. The distribution of these flexible moments along a beam or structural element is graphically represented by moment diagrams. These diagrams identify the zones of greatest stress, facilitating an adequate and safe design. For a simple beam, the maximum moment, represented by the value , occurs specifically at the center of the span.
In the context of structural design, there is a fundamental difference between design by allowable stresses and limit design. Design by allowable stresses works within safe stress ranges within the elastic limit of the material, whereas limit design considers the maximum resistant capacity of the structure just before failure. When calculating allowable stresses, a factor of safety is employed, ensuring that the calculated stresses are significantly lower than the limit stress of the material.
Regarding the elastic behavior of beams, the elastic flexion formula is expressed as:
In this equation, the letter represents the Moment of Inertia. Additionally, structural analysis must account for shear flow (fluencia de cortante). This study examines how shear stresses act and are distributed both horizontally and vertically within the beams, and how these forces influence the overall stability of the structure. Excessive shear can lead to diagonal cracks; therefore, stirrups (estribos) are used to support excess shear where concrete fails. Their spacing is defined by ACI formulas, and it is a requirement that the spacing must be less than the depth () to effectively prevent diagonal cracking.
Deflections and Slenderness in Structural Elements
Deflections are primary indicators of the conduct and proper functioning of a structural member. The total deflection in a beam depends on the distribution of curvature across the entire length of the beam and the specific support conditions. In the case of slender beams, deflections can be very high even if the internal stresses remain low.
Excessive deflections are highly undesirable for several practical and aesthetic reasons:
- They can produce cracks in ceilings and floors.
- They cause localized damage to partitions and can lead to leaks (goteras).
- They cause physical discomfort to occupants, particularly when movement is caused by wind, machinery, or vehicles.
- They can provoke mechanical breakdowns or malfunctions within the building's systems.
- They can cause secondary stresses and undesirable aesthetic effects.
When determining the optimal span-to-depth ratios (), several factors must be considered, including economy, flexion limitations, vibration issues, aesthetic requirements, practical requirements, and the possible movements of the structure. These ratios are further influenced by the material, loads, section shape, and support conditions. Notably, the ratios for cantilevers (voladizos) must be lower than those for simply supported elements because cantilevers handle higher moments and deformations, requiring a greater depth to ensure stability.
The Principles and Methods of Prestressing
Prestressing is the intentional production of internal forces and permanent stresses or tension in a structure or assembled set to improve its behavior and resistance under various service conditions. This process is essentially an attempt to redistribute part of the external loads by inducing an internal counter-load through the tensioning of a curved tendon. For concrete, prestressing is especially beneficial because concrete is naturally strong in compression but weak in tension. By prestressing steel against the concrete, the concrete is subjected to a compressive stress that offsets the tension produced by external loads. The stresses of pre-compression for beams are generally limited to a range of to .
There are two primary methods for prestressing concrete:
- Pre-tensioning (Preesforzado): In this method, the tendons (wires or strands) are tensioned against supports or formwork before the concrete is poured. Once the concrete has hardened, the tension is released, and the force is transferred to the concrete through bonding.
- Post-tensioning (Postensado): This involves tensioning the tendons against the concrete after it has hardened, usually using hydraulic jacks.
Advanced Concepts in Prestressing and Load Balancing
There are three basic concepts used to explain the behavior of prestressed concrete:
- First Concept: Prestressing to transform the concrete into an elastic material.
- Second Concept: Prestressing for the efficient combination of high-strength steel and concrete (internal resisting couple). In this view, the lever arm () is variable and increases as the external moment increases, determined by the formula .
- Third Concept: Prestressing to distribute external loads through the use of curved (parabolic) tendons. This induces an upward internal load to support vertical downward loads. This is often referred to as "load partitioning" (repartición de carga), a concept that simplifies preliminary design using the formula .
A key term in stress distribution is the "Kern point" of a section. This is the center of elastic stress located above or below the neutral axis. If the compression force () acts within the limits of the Kern point, a triangular stress distribution is achieved. It is also noted that curved tendons require an initial prestress approximately higher than straight tendons to account for losses due to friction.
Material Evolution, Connections, and Practical Construction
Historically, steel members were connected using rivets (remachado). However, this practice has been almost entirely replaced by high-tension bolts. Additionally, the welding of steel has become a generalized and common practice, particularly in fabrication plants, though it is also applied on-site. Connections are a vital part of building design because they allow for the correct transmission of loads and stresses between different structural elements, ensuring stability, continuity, and safety.
In comparing prestressed concrete to reinforced concrete, prestressed concrete allows for longer spans with less steel, though the material itself is more expensive. Formwork costs are similar, and precasting becomes cost-effective if there is a high degree of repetition.
In building construction, certain structural configurations present practical difficulties:
- Triangular Trusses in Walls: These are often inconvenient for floor construction because the diagonal members obstruct essential openings such as doors and windows.
- Vertical Shaft Bracing: Bracing or reinforcing a vertical shaft (cañón vertical) is performed to increase its resistance and stiffness against lateral forces.
- Negative Moment: If the ends of a beam are embedded (empotrada), they are subjected to a convex curvature known as Negative Moment. Resistance to rotation at the ends of a beam causes the moment curve to shift toward the supports.