Soil Science
Chapter 1
The Soils Around Us
Services
The degree to which we depend on soils is likely to increase.
Soils have six key roles:
Support plant growth
Regulate water supplies and purity
Recycles organic waste
Habitat for soil organisms
Engineering medium
Plant Growth
Physical support - plants are anchored in the soil.
Ventilation - Root respiration uses O2 and produces CO2 so it needs replenishment.
Water - soil absorbs water which the roots require a continuous stream of for cooling, nutrient transport, turgidity, and photosynthesis.
Temperature moderation - the surface of the soil is much hotter/colder compared to just a few centimeters below due to its insulating properties.
Toxin protection - phytotoxic substances are in the soil from human activity/naturally produced, and soils can mitigate this.
Mineral nutrition - soils supply dissolved mineral nutrients that the plants take up.
Plants need 17 essential elements. In large amounts they are macronutrients, and micronutrients in small amounts.
Plants can grow in nutrient solutions called hydroponics but this requires time, energy, and management.
Where plants are grown in nutrient-deficient soil, the local human population generally also exhibit deficiencies in the nutrient.
Being in close contact with healthy soils and breathing in certain microorganisms and volatile compounds they produce gives people a sense of wellbeing through interactions with their brain chemistry.
Regulate Water
Water soaks into the soil. It can be used by plants, be stored in the soil, or seep through to the groundwater over months or years as base flow.
As water soaks through soil, it is purified and pathogens are killed.
Recycling Waste
Dead plants, animals, and their waste are broken down and assimilate into the soil in forms that can be utilized by life. Soils can accumulate large quantities of carbon from this process, reducing atmospheric CO2.
The critical zone is the layers of the planet that exist between the tops of the trees to the bottom of the aquifers.
The soil (pedosphere) is an interface between the lithosphere, atmosphere, hydrosphere, and biosphere.
Soil is a material composed of minerals, gases, water, organic substances, and microorganisms.
Soils are natural bodies composed of soil, roots, animals, rocks, artifacts, etc.
The regolith is the layer of unconsolidated debris overlying the hard unweathered rock. It varies from nonexistant (exposed bare rock) to tens of meters in depth.
When the underlying rock is weathered to be loose enough to be dug with a shovel, it is called saprolite.
Living organisms and plant roots alter the regolith through biochemical and physical efforts.
Soil Profile
O horizon : organic remains or materials of plants and animals accumulate on the surface. The are physically and chemically broken down and create the organic soil surface.
A horizon - water and soil animals move some of the O horizon organic content downward to intermingle with the mineral grains of the regolith. Clay and other products of weathering are also leached to this layer. So the A horizon are generally dominated by mineral particles but have been darkened by organic matter.
E horizon - in some soils, just below the A horizon there is a layer of intensely weathered and leached soil that does not have organic matter.
B horizon - the layers underlying A and O horizon contain various amounts of silicate clays, iron, aluminium oxides, gypsum and calcium with very little organic matter. These materials have been washed down from above or formed through the weathering process.
C horizon - plant roots and animals can extend below the B horizon, especially in humid regions. They cause chemical changes to the soil water, some biochemical weathering of the regolith, and form the least weathered layer - the C horizon.
Topsoil is another name for the A horizon. When it is cultivated it is called the plow layer. The properties of the topsoil are much more conducive to plant growth than the subsoil. So agricultural productivity can often be correlated with the thickness of the topsoil layer.
Soil Composition
The proportions of air, water, mineral matter, and organic matter influence the behavior and productivity of soils. While a handful of soil may seem to be solid material, about half of it is pore spaces filled with air or water. Generally, only 5% of the volume of ideal soil is organic matter, or 2% of its weight.
Soils with more than 50% volume in solids are likely to be too compacted for good growth.
In optimal conditions, the pore spaces will be 25% air, 25% water. More or less water indicates waterlogged or drought accordingly.
Soil particles are broken into 4 main sizes
Stone, gravel.
Sand = 2.0-0.05mm, feel gritty when rubbed, not sticky.
Silt = 0.05-0.002mm, cannot be felt individually, feels smooth but not sticky, even when wet.
Clay = <0.002mm, when wet they stick together in a sticky mass, when dry they form hard clods. They have colloidal properties. They have a tremendous amount of surface area due to their tiny size.
Soil biomass refers to the living organisms that are found within.
Soil Water
Water held within soil pores loses a lot of its ability to flow due to the attraction between the particles of water and soil.
Soil water contains hundreds of dissolved organic and inorganic substances, so we may actually call it a soil solution.
Plant roots first take water from the largest pores, and then the intermediate pores.
Water in the smallest pores cannot be taken up by the plant because it is held too strongly by the solid particles. So 1/6 to ½ of water may remain in soil after plants die from lack of moisture.
Buffering capacity is the ability of the soil to resist changes in its composition.
The relative humidity of soil air often approaches 100% while the soil air contains highly concentrated CO2.
The amount and composition of soil air is largely determined by the water content of the soil.
Plant Roots
To take up nutrients, the element must be in a soluble form and located at the root surface.
The plant takes up nutrients through root interception, diffusion, and mass flow.
Root hair growth is influenced by a gene that is activated by low nutrient conditions.
Plant roots are always actively drawing up water from the soil, so the water in soil pores moves towards the roots and nutrients are carried along with it in what is known as mass flow.
Nutrient ions continuously move by diffusion from areas of greater concentration to lower concentration ie. around the root hairs.
Soil compaction, cold temperatures, and low soil moisture content can reduce root interception, mass flow and diffusion and this leads to poor nutrient uptake even in soils with adequate supplies.
The root membrane is embedded with large protein molecules. Each molecule is responsible for one nutrient. These molecules form hydrophilic channels across the membrane. Metabolism created in the root cell provides energy to activate the protein, allowing it to react with the nutrient ion and pass it into the cell. This mechanism enables the plant to somewhat control the proportions of elements taken up.
So nutrient uptake is part of the metabolic process. If this process is inhibited by excessive soil water content, compact soil, poor aeration, excessive temperatures, or aboveground conditions affecting translocation, the nutrient uptake will also be inhibited.
Soil Health
While soils are reuseable, they are not renewable in terms of human life span.
Many of the world’s cities are located on excellent soils that supported thriving agricultural communities but are now lost to suburban development.
Soil quality is the measure of the ability of a soil to carry out particular ecological functions. It reflects a combination of chemical, physical, and biological properties.
Soil is damaged by:
Removal of the topsoil + erosion
Accumulation of salts in improperly irrigated soils and arid regions
Cultivation without returning organic residues
Contamination with toxic substances
Questions:
1. As a society, will our reliance on soils increase or decrease in coming decades?
A: Our reliance will likely increase, due to the growing population trend, leading to the need for more food. Soils will be farmed intensively in order to provide for the population. A larger population also puts a demand on more space, biofuels, and fiber.
2. How does a soil differ from soil?
A: Soil is a general noun that refers to the material itself. A soil is like saying a lake. It refers to a specific, 3D body in the landscape with its own unique characteristics.
3. What are the six main roles of soil in an ecosystem?
A: Medium for plant growth, regulate water supplies, modify the atmosphere (sequester CO2 ex), recycle raw materials/waste, provide habitat, be an engineering medium.
4. i) Draw a pie chart to represent the above loam surface soil composition after being compacted by heavy traffic.
ii) Draw a pie chart to show how the four components of the original soil would be related on a mass basis rather than on a volume basis.
A: i) If the soil was compacted by heavy traffic then the percentage air and water would become much less as the pore spaces are squeezed. Soil solids would take up a lot more volume.
ii) If by mass instead of volume, air would be the smallest (~0), followed by organic (~1-5). Water would be less than minerals which would remain the largest (~90).
5. Explain how the soil’s nutrient supply is held in different forms.
A: Most of the soil’s nutrients are not in use, they are stored in the soil for longterm retention. A small percentage of the nutrients are dissolved in soil solution and are available for use by plants and organisms.
6. List the essential nutrient elements that plants derive mainly from the soil.
A: Iron, zinc, calcium, copper, chlorine, molybdenum, magnesium, manganese, posphorus, potassium, sulphur, selenium, nitrogen, nickel, boron.
Hydrogen, oxygen, carbon come from the air.
7. Are all elements contained in plants essential nutrients?
A: No, they are not all essential as not every plant needs exactly the same nutrients and some plants can live without certain ones. Plants also often take up non-essential elements passively from the environment. An element is only essential if the plant cannot complete its lifecycle without it.
8. Define these terms:
i) Soil texture is the relative proportions of sand, silt, and clay sized particles in the soil.
ii) Soil structure is the arrangement or aggregation of primary soil particles into larger units (peds/clods)
iii) Soil pH is the acidity/alkalinity of the soil.
iv) Humus is the stable, highly decomposed part of soil matter found in the solum.
v) Soil profile is the makeup of the horizons of a soil, can be viewed in a vertical cross-section.
vi) B horizon is the subsoil between A and E. It is characterized by the accumulation of clays, iron, aluminum, or humus washed down from above (illuviation) and has lower organic matter than A horizon.
vii) Soil quality refers to the ability of the soil to perform a specific ecological function.
viii) Solum is the A, E, and B horizons combined, where most root growth and major soil-forming processes take place.
ix) Saprolite is weathered crumbly bedrock that has lost its original rock strength but retains the structural features and arrangement of parent rock.
9. Describe four processes that lead to degredation of soil quality.
A: Removal of topsoil due to erosion. Introduction of toxic substances. Intensive farming without replenishing organic residue. Accumulation of salts in improperly irrigated soils.
10. Compare the pedological and edaphological approaches to the study of soils. Which is more closely aligned with geology and which is aligned with ecology?
A: Pedology follows systems of soil origin, classification and theorizes interrelations between soils (geology). Edaphology is concerned with the influence that soil has on living things (ecology).
Chapter 2
Formation of Soils From Parent Materials
Weathering breaks up rocks and minerals and modifies or destroys their physical and chemical characteristics. It also synthesizes new materials.
Igneous
Composed of primary materials:
Light-colored quartz
Muscovite (light)
Feldspars (light)
Dark-colored biotite
Augite (dark)
Hornblende (dark)
The grains in igneous rocks interlock and are randomly dispersed, giving a salt-and-pepper appearance.
Generally, the dark-colored minerals contain iron and magnesium, and these are more easily weathered.
So dark-colored igneous rocks (basalt, gabbro) are more easily broken down that lighter-colored ones (granite, syenite)
Sedimentary
Most common rocks on Earth, about 75% of the land surface.
Granite is weathered into quartz sand which is cemented by calcium or iron in the water to become sandstone.
Clays compact into shale.
Calcite is the dominant mineral in limestone.
The resistance of a particular sedimentary rock to weathering is governed by its dominant minerals and the cementing agent.
Metamorphic
Metamorphic rocks are usually harder and more strongly crystalline.
Recrystallization may produce crystals of the same minerals that are usually larger, or elements from original minerals may recombine to form new minerals.
Granite becomes gneiss
Limestone becomes marble
Sandstone becomes quartzite
Shale becomes slate
Slate becomes phyllite or schist (containing mica)
General Weathering
Original forms are destroyed by physical disintegration and chemical decomposition.
Physical weathering (disintegration)
Plants and animals have little influence.
Temperature: Hot and cold temperature changes causes expansion and contraction of constituent materials of rocks. Some minerals expand more, creating stresses that eventually cause rocks to crack apart.
The outer surface of the rock will be more affected so some rocks weather by exfoliation - peeling away of outer layers. If ice forms in the surface cracks, it can accelerate the process.
Abrasion: Rocks are cut down by water, ice, and windblown dust and sand.
Biogeochemical weathering
Chemical reactions are most intense in wet and hot climates, but is accentuated by physical weathering and vice-versa. E.G. abrasion decreases size of particles thereby increasing surface area, making them more susceptible to rapid chemical reactions.
Chemical weathering is enhanced by geological agents E.G. presence of water/oxygen, and by biological agents E.G. acids produced by microbes/plant roots.
Hydration: Minerals absorb water directly into their crystal structure causing the rock to swell and weaken. Intact water molecules bind to a mineral eg. hematite + water → ferrihydrite
Hydrolysis: Water molecules split into H⁺ and OH⁻ ions and chemically react with minerals, breaking them down into entirely new compounds (like turning feldspar into clay).
Dissolution: Water hydrates cations and anions until they dissociate from one another ie. dissolve. Eg. water and gypsum.
Acid reactions: Acids (like carbonic or sulfuric acid) introduce high concentrations of hydrogen ions that aggressively break down and dissolve mineral structures.
Oxidation-reduction: Minerals containing iron, manganese, or sulphur are especially susceptible. Minerals lose or gain electrons through reactions with oxygen and water, which changes their chemical stability (such as iron-rich rocks rusting). It is often obvious due to changes in the colors of the resulting altered minerals.
Complexation: Soil biological processes produce organic acids such as oxalic, citric, and tartaric acids.Organic acids produced by plants or fungi bind to metal ions in rocks, pulling them out of the mineral structure and speeding up decay.
Soil Formation Factors
Si = f (cl, o, r, p, t)
Si is a particular soil property
Cl is climate, mostly precipitation and temperature
O is organisms
R is relief or topography
P is parent materials
T is time
Under these factors, soils are defined as dynamic natural bodies having properties derived from the combined effects of climate and biotic activities, as modified by topography, acting on parent materials over periods of time.
Lithosequence, climosequence, biosequence, toposequence, chronosequence : a sequence of soils that varies in characteristics due to differences in (climate).
Parent Materials (PM)
The nature of the parent material greatly influences soil characteristics:
A quartz-rich PM such as granite or sandstone gives a sandy-textured soil.
Limestone will slow the development of acidity in humid climates.
Residual PM develops in place from weathering of the underlying rock. In stable landscapes it may have long, intense weathering.
In warm, humid climates, residual PM are typically thoroughly leached and oxidized, showing red and yellow colors of oxidized iron compounds. In cooler, drier climates, the color and composition will remain similar to PM.
Colluvium is loose, unconsolidated rock fragments generally deposited at the base of slopes.
Colluvial PMs are usually coarse and stoney because they have been physically weathered. Stones, gravel and fine material are interspersed, not layered. Colluvial deposits usually are very well drained but also unstable and subject to landslides due to the packing voids created when tumbling rocks rest against each other.
Talus/scree is rock fragments. Detritus is rock debris.
Soils derived from alluvial sediments generally have characteristics that are desireable for human agriculture/settlement. These features include topography, proximity to water, high fertility, and high productivity.
Alluvial deposits have three general classes:
Floodplains are where flood waters have deposited sediments. Coarser materials are found closer to the river channel, while finer materials settle out in the calmer flood waters. Each flooding episode creates a distinctive layer, forming the characteristic stratification of alluvial soils.
As the river cuts down, terraces are left above the new flood plane.Alluvial fans are formed when streams leave a narrow upland valley and suddenly descend into a broader valley below. The water spreads out and slows down so it deposits sediment in a fan-shape. These soils are often very productive but may be quite coarse-textured.
Delta deposits is when fine sediments from streams is discharged into the lake or ocean and some of the suspended sediments settle near the mouth of the river, forming a delta. They’re generally clayey in nature and poorly drained. They are important wetland habitats but often used for rice.
Coastal sediments are where much of the streams sediments end up, with coarser fragments settling closer to shore. They generally form moderate slops which are more level nearer to coastline and hillier farther inland.
Marine and coastal deposits vary in texture - some sandy, some clayey. Where streams have cut down, layers of clay, silt, and sand can be seen side by side - all of them coming from upland erosion.
Because seawater is high in sulphur a lot of marine sediments are too.
(Glacial) till refers to the materials deposited directly by the ice. It’s an unstratified mixture of debris varying in size from boulder to clay. The fragments are usually more rounded due to the grinding from the ice. Deposits are densely compacted due to the weight of the overlying ice sheets. Much till is deposited as morraine.
Drift is the term used to apply to all material of glacial origin.
Glacial outwash refers to the sediments that were carried out from melting glaciers by the water. In valleys or plains where the water could flow freely, the sediment formed an outwash plain with the sediment referred to as valley fill.
When the ice came to a standstill with no ready escape for the water, ponding began with lacustrine deposits. The soils of these dried lakes are inherently fertile but may not be well drained.
Wind (eolian) can pick up an enormous quantity of material from soil that is loose, dry, and unprotected by vegetation.
Materials include dune sand, loess, aerosolic dust and volcanic ash.
Dune sand mainly consists of quartz which is devoid of plant nutrients and highly resistant to weathering. Over time, hardy dune grasses can take root and initiate the soil-forming process.
Loess is primarily composed of silt with some very fine sand and coarse clay.
Aerosolic dust is made of very fine particles and can remain suspended in the air for thousands of kilometers before being deposited, usually with rainfall. Much of the calcium found in South America comes from the Sahara Desert.
Organic deposits (peat) accumulate in wet places (bogs) where plant growth exceeds the rate of decomposition - it is slow in the water due to lack of oxygen.
Peats are mostly found in cool climates. 75% of peat lands are found in Canada and Russia.
There are four kinds of peat based on the nature of the PMs:
Moss peat - too acidic for farming.
Herbaceous peat
Woody peat - great for farming.
Sedimentary peat (from remains of aquatic plants and fecal matter of animals/fungi) - undesirable for farming, too colloidal.
(Fens are similar to bogs but they have received calcium-rich minerals from the surrounding landscape, so they are quite alkaline whereas bogs are acidic.
Swamps are periodically inundated with shallow water and dominated by trees and shrubs.
Marshes are much the same as swamps but their vegetation is dominated by grasses and herbaceous plants.)
Organic deposits usually contain two or more of these kinds of peat, as layers or mixtures. Woody peat often dominates the surface as trees eventually dominate.
Peat can be termed fibric if plant fiber residues are intact enough to be identified. If the material has decomposed to have little fiber remaining, it is called muck or sapric.
Role of Climate
Climate may be the most influential factor on PM because it determines weathering over large geographic areas.
Effective precipitation
Seasonal distribution. 600mm falling over 12 months will cause less leaching than 600mm falling in 6 months.
Temperature and precipitation. In a hot climate, much less of the 600mm will be available for percolating and leaching because it evaporates quickly.
Topography. Water on a steep slope will run downhill rapidly, only a small portion will enter the soil where it falls.
Permeability. A coarse, sandy profile will allow more rainwater to leach through than a tight, clayey one.
Therefore, a sandy soil in a flat or concave site in a cool climate with even dispersed rainfall will experience greater effective precipitation and more rapid soil development.
Soils that experience effective annual precipitation generally have increasing clay and organic matter contents, greater acidity, and lower ratio of Si-Al which is an indication of more highly weathered minerals.
Role of Living Organisms

Vegetation
Grasslands: Most of the organic matter added to the soil is from deep fibrous root systems.
Grassland fires destroy aboveground biomass and add bits of charcoal into the soil.
The microbial community is dominated by bacteria.Forests: Tree leaves are a principal source of organic matter.
Certain forests have extreme acidity that inhibits soil mixing by earthworms etc.
Forests characteristically store most of their organic matter in the O horizon (forest floor)
The microbial community is dominated by fungi.Conclusion: Grassland soils generally have a thicker A horizon with deep distinction of organic matter. The light-coloured E horizon in acidic forest soil generally forms from the organic acids made by fungi.
Q: Why doesn’t the grassland have an E horizon compared to the forest?
A: Rainfall in a forest reacts with the acidic organic litter to create powerful acids that dissolve and wash away the upper mineral layer. In addition, the forest organic litter is concentrated near the surface, so it doesn’t provide much of a barrier.
Cation Cycling
Biochemical weathering accelerates the release of nutrient elements from minerals. This strongly influences the characteristics of the soils that develop, especially its acidity.
Deciduous forests: the tree roots take up a lot of cations of calcium, magnesium, and potassium.
The leaves break down readily and form a thinner forest floor with less distinction between layers and more litter mixed into A horizon.Coniferous forests: the trees take up very little Ca, Mg, and K, so these nonacidic cations are lost to leaching.
The needles are acidic and resinous so they resist decomposition and discourage earthworms.
This all leads to a more acidic soil with a thick O horizon divided into distinct fibric (undecomposed) and sapric (highly decomposed) layers.
(Rangelands
Arid and semiarid rangelands have limited water that does not allow for vegetation dense enough to cover the soil surface.
Scattered shrubs are interspersed with openings in the plant canopy where the soil is bare.
The plants trap windblown dust that can be rich in silt and clay.
Roots that scavenge nutrients from the interplant area then deposit them with the leave litter.
The decaying litter adds organic acids which lower the soil pH and stimulate mineral weathering.
Through these processes, as time goes on, the bare soil between plants declines in fertility and increases in size, while the plants form their own “islands” of enhanced fertility and thicker A horizons. )
Role of Animals
Large animals bore into lower soil horizons, bringing material to the surface and enhancing mixing of upper and lower horizons. Their tunnels, open to the surface, encourage movement of water and air into lower layers.
Old burrows can naturally refill with A horizon matter, creating crotovinas.
Pedoturbation accelerates erosion. Gophers make tunnels in the snow and pack them with fine soil which becomes easily eroded once the snow melts.Invertebrates mix the soil as they burrow.
Earthworms ingest soil particles and organic residues and excrete enhanced availability plant nutrients.
They aerate the soil and enhance aggregation.
Ants and termites transport between horizons as they build mounds but mounds can also cause erosion and soil loss.Humans have wide influence on soil. Plant burning or removal for cultivation and tillage, irrigation, fertilizing, bulldozer levelling, new soil engineering (golf greens), dredging.
Role of Topography
Steep slopes encourage rapid soil loss by erosion and allow less rainfall to enter the soil before running off. It can also result in less complete vegetative cover.
Soils on steep terrain generally have shallow, poorly developed profiles.In depressions, runoff water is collected, leading to a more deeply weathered regolith and advanced soil profile development.
Sometimes, the water may saturate the regolith, restricting drainage and aeration, and features of wetland soils may develop.
Soils that commonly occur together in a landscape are called catena/toposequence.
Topography has the following affects:
Interaction with vegetation. E.g. in grassland-forest transition zones, trees are confined to depressions
Slope aspect affects absorbance of solar energy.
Salt buildup in lower-lying areas of arid-semiarid regions.
Interactions with PM, the topography will influence distribution of residual, colluvial, and alluvial PM.
Role of Time
The weathering of rock generally creates only 0.01-0.1mm of new soil per year.
On tropical steep slopes with thin soils, that rate can be as high as 2mm per year.
Time also influences pedological features.
Example timeline in years:
100 - lichen and moss grow on exposed rock, accelerating its breakdown and contributing organic matter.
500 - grasses, shrubs, stunted trees take root in deepening layer of disintegrated rock and soil. They add to the accumulation of organic materials to form A and C horizons.
10,000 - successions of forest trees and multitude of soil organisms create distinct O horizon while thickening and darkening A horizon. Bleached E horizon develops below.
Processes of Soil Formation
Genesis is the formation of soil from parent material and is generally brought about by 4 main pedogenic processes.
1. Transformations
Soil constituents are chemically or physically modified or destroyed, and others are synthesized from the precursor materials, especially silicate clays.
Products of decomposition also reform into new minerals including more silicate clays and hydrous oxides of iron and aluminum.
Other transformation change the size or arrangement of mineral particles.
2. Translocations
The movement or materials laterally within a horizon, or vertically through horizons, usually caused by water.
Common minerals moved are fine clay particles, dissolved salts, and dissolved organic substances.
Soil organisms also transport quite a bit.
3. Additions
Inputs of materials to a developing soil profile from outside sources, eg. the addition of carbon from the fallen leaves/roots of plants.
Dust particles falling is another ubiquitous addition.
4. Losses
Materials are lost by leaching to groundwater, erosion of surface materials, and volatilization of gases.
Water is lost through evaporation, plant use, and leaching.
Dissolved substances are lost by leaching and drainage.
Carbon, nitrogen, and sulphur are lost as gases by fire and biochemical reactions.
Fine particles on the surface are lost by erosion.
Grazing removes a lot of both organic matter and nutrient elements.
Horizon Formation
A horizon: organic-mineral mixture.
Dark in color.
Chemical and physical properties differ from PM.
Individual soil particles clump together under the influence of organic substances to form granules, differentiating this layer from others.B + C horizons: acidic rainwater dissovles (transformation) various minerals and leaches (translocation) them to lower horizons, creating eluvial zones of depletion in upper layers and illuvial zones of accumulation in lower layers.
Bk layers are enriched in calcite or gypsum.
Bt layers are enriched in silicate clay.E horizons: leached of clay, iron, and aluminum oxides, so a concentration of resistant materials (quartz) is left.
Common in forests, not in grasslands.
B horizons: the PM structure is no longer discernable.
Materials have accumulated by illuviation.C horizon: unconsolidated material under the solum.
In dry regions, carbonates and gypsum may be concentrated here.
The material is saprolite - retains some structural features of PM but is loose enough to be dug by a shovel.
Sub-Horizons
There are six master horizons: O, A, E, B, C, R, within which subhorizons may occur eg. Bt, Oi, Ap.
O horizons:
- Oi is made of fibric materials, ie. only slightly decomposed, still recognizable parts.
- Oe is made of hemic materials, ie. intermediate decay, much fiber evident when rubbed between fingers.
- Oa is made of sapric materials, ie. highly decomposed with little fiber or recognizable tissues. Common only in forested land.
B horizons:
- Bt have maximum accumulation of iron and aluminum oxides and silicate clays.
- Bk have accumulation of calcium carbonate.
- By have accumulation of calcium sulphate.
Horizon Terms
Distinctive layers with a master horizon denoted by B1-B2-B3, etc.
Two different geologic PMs present, denoted as O-A-B-2C
Layers transported by humans denoted as ^A-^C-2Ab-2Btb
Transition layers denoted as AE, BC etc. with the first letter designating dominance.
A ployed soil gains a plow layer of the first 15-20cm, aka the mostly homogeneous Ap horizon.

A truncated profile may form in seriously eroded cultivated land - surface soil is swept away so the plow reaches deeper each year. In this case, the plow zone can be almost entirely made up of former B horizon.
Urban Soils
Accounts for 3% of the Earth’s land surface.
Profile: Urban soils are heavily influenced by human bioturbation - reworked by shoveling to bulldozing. Also by excavated soil being reapplied as a fill layer on top of existing soil (typically ^Au horizon).
Urban soil profiles include layers of: geotextile fabric, sand or gravel, compacted clay, building rubble or artifacts, paving asphalt etc.
Physical properties: Urban soils can be heavily compacted due to weight of structures and traffic.
There can be abrupt boundaries between highly contrasting materials eg. layers of gravel under layers of clay. While desirable for engineering, this can create major problems for water percolation and tree root growth.
Chemical properties: Concrete and cement can create very alkaline soils in high rainfall areas where acidic soils would be expected. These soils can also be less thoroughly leached than expected for local climate.
They are often contaminated - lead, toxic metals, de-icing salts, petroleum, dissolving concrete, rusting iron nails, sewage etc.
Biological properties: the vegetation in urban soils is a lot less and generally not reflective of natural succession and local plants. Soils can be very inhospitable also due to compaction and low organic matter.
Urban heat island effect can increase plant growth and microbial decomposition.
Questions
1. What is meant by weathering combines the processes of destruction and synthesis? Give an example of these two processes in the weathering of a primary material.
A: Destruction involves disintegration and decomposition. Primary rocks and minerals are broken down into smaller fragments and soluble ions via physical and chemical weathering.
Synthesis is the recombination of those released ions and components into secondary minerals, like feldspar break down and the dissolved silicon and aluminum recombine into secondary silicate clays.
2. How is water involved in the main types of chemical weathering reactions?
A: Water is involved in:
hydrolysis - split into H+ and OH- ions which break down crystal structures of PMs.
hydration - water molecules bind directly into the crystal structure, expanding and weakening it.
dissolution - water hydrates and dissolves soluble salts and minerals into free ions.
carbonation - water reacts with CO2 to become acidic and breakdown minerals in rocks like calcite.
3. Explain the weathering significance of the ratio of silicon to aluminum in soil minerals.
A: A high Si:Al ratio indicates a young or moderately weathered soil, where silica hasn’t had time to wash away. A lower ratio indicates an intensely weathered and highly leached (sub)tropical soil.
Silica is highly soluble and washes away easily, leaving behind aluminum and iron oxides.
4. Give an example of how parent material may vary across large geographic regions on one hand but may also vary within a small parcel of land on the other.
A: PM can vary across large regions because of major events like continental glaciation or massive wind-blown eolian deposits (loess belts)
In a small parcel of land, differentiation is primarily driven by topography and local transport agents, like on a hillside, there may be residual bedrock weathering on steep areas and piled up colluvium downslope.
5: Name the five factors affecting soil formation. Compare a forested rocky mountain slope to the semiarid grassland plains far below.
A: Topography, time, PM, climate, living organisms.
Forested slope: topography means quick water runoff and faster erosion. Needs longer time to form deeper layers. PM can be bedrock compared to colluvium. Climate can be cooler and wetter on slopes. Living organisms are trees which provide leaves for O horizon and thin A horizon compared to thick A horizon of grasslands.
6. How do colluvium, glacial till, and alluvium differ in appearance and agency of transport?
A: Colluvium is things such as scree, rubble that moves by gravity down slopes. It is often not layered and quite unstable, with gaps between larger angular materials filled with finer debris.
Glacial till is unconsolidated mix of PM that is moved by ice and left in situ as ice retreats.
Alluvium is transported by water and stratified and sorted by particle size with largest particles closest to where the flow starts to weaken and smaller particles deposited further out.
7. What is loess and what are some of its properties as a PM?
A: Loess is wind-blown silt. It has a uniform texture, excellent water-holding capacity, and high natural fertility. It is one of the most productive agricultural soils in the world.
8. Give two specific examples of each of the four broad processes of soil formation.
A: Addition: Falling debris from plants. Dust settling from the atmosphere.
Loss: Minerals from leaching to waterbed. Topsoil lost to erosion.
Translocation: material is moved laterally in a layer by organisms. Material is moved vertically between layers by illuviation or eluviation.
Transformation: primary minerals chemically breakdown and weather into secondary minerlas like silicate clays. Organic residues chemically decompose and transform into humus.
9. With a level layer of granite rock as PM, how would soil profile differ in warm semiarid grassland to cool, humid pine forest?
A: The grassland would have deep distinct two layers of A horizon due to the rich thick mass of roots. There would be no E horizon or O horizon. The forest would have O horizon often with subhorizons within such as Oi, Oe, and Oa. The A horizon would be thin and often followed by an E horizon.
Chapter 4
Soil Architecture and Physical Properties
Soil architecture lets us think about the primary particles in soil as bricks in a house.
Soil texture describes the size of soil particles.
Soil structure describes the manner in which soil particles are aggregated.
Soil Colour
Colour has little effect on soils but it provides clues about properties and condition of soil.
The Munsell colour charts are arranged into hue (red- or yellowness), value (light- or darkness), and chroma (intensity or brightness)
In a Munsell color book, value increases from top to bottom, chroma increasing from left to right, and hues changing per page.
Causes of different colours
There are three major influencing factors: organic matter content, water content, presence and oxidation states of iron and manganese oxides in various minerals.
Organic matter coat mineral particles, darkening and masking the brighter colours of the minerals.
Water: Soils are darker when wet. Water influences oxygen levels and thereby the rate of organic matter accumulation which darkens the soil. Water affects the oxidation state of iron and manganese.
Oxides: Well-oxidized iron compounds impart bright reds and browns to the soil.
Manganese oxide imparts black.
Glauconite imparts green.
Calcite and soluble salts in dry regions impart white.
Reduced iron compounds impart gray and blue in poorly drained soils.
Soil that exhibits grey colours from reduced iron and iron depletion is said to be gleyed - often from iron in prolonged anaerobic conditions.
The depth in the profile at which gleys are found helps to define the drainage class of the soil. Meanwhile, the presence of gleys in the upper layers delineates wetlands as it is inidicative of waterlogged conditions.
Residual vs colluvium vs alluvium
Soil Texture
Diameters of soil particles are measured over six orderes of magnitude from boulders (1m) to submicroscopic clays (<10-6m).
Soil texture mainly refers to the fine earth fraction of particles less than 2mm in diameter.
Sand: 2mm-0.05mm.
Feels gritty between the fingers.
Particles generally visible to naked eye.
Particles may be rotund or angular.
Usually quartz (SiO2) or primary silicate materials.
Lacks nutrients for plant growth.
Large particles means that whatever nutrients are present are not likely to be released for plant uptake.
Large pores means water drains rapidly and promote entry of air.Silt: 0.05mm-0.002mm.
Particles are too small to be visible to naked eye.
Feels smooth or silky between the fingers.
When made of weatherable minerals, small size of particles allows weathering rapid enough to release significant amounts of plant nutrients.
Retains water well without stickiness or plasticity.
Highly susceptible to erosion, easily washed away by flowing water = piping.Clay: <0.002mm.
Tremendous surface area and capacity to adsorb water and other substances.
Particles cohere in a hard mass after drying.
High plasticity when wet.
Behave as colloids.
Small pores means water and air movement is very slow, also unavailable to plants.
The kind and amount of clay present determines the soil properties.
There are five phenomena of surface area that influence other soil properties:
Water forms thin films on soil particles. Therefore, the greater the surface area, the greater the soil’s capacity for holding water films.
Gases and dissolved chemicals are attracter to and adsorbed by mineral particle surfaces. Therefore, the greater the surface area, the greater the soil’s capacity to retain nutrients and other chemicals.
Weathering occurs on the surface, releasing constituent elements into soil solution. Therefore, the greater the surface area, the greater the rate of release of plant nutrients from weatherable minerals.
Surfaces of mineral particles carry negative and positive electromagnetic charges that cause particle surfaces and water films to attract each other. Therefore, the greater the surface area, the greater the propensity for soil particles to stick together.
Microbes colonize particle surfaces.
Sands are well aerated, loose, infertile, prone to drought.
Soil Textural Classes
There are three broad groups of soils, sandy, clayey, and loamy, and within these there are specific textural class names, which is often displayed using the textural triangle.
Most soils are some type of loam.
Loam is a micture of sand, silt, and clay particles that exhibits the properties of those separates in about equal proportions. This does not mean they are in equal amounts.
A soil with high amounts of coarse fragments are distinguished using modifiers.
2-75mm diameter fragments are termed gravel or pebbles.
75-250mm are termed cobbles if round or channers if flat.
>250mm are termed stones or boulders.
Textural class analysis can be done by the feel method or in the lab.
In the lab process:
Complete dispersion of soil sample in water, usually achieved with chemical treatments and high-speed blender, shaker, or ultrasonic vibrator.
Sieving to separate coarse fragments and sand separates. Silt and clay fractions pass through.
Sedimentation to determine amounts of silt and clay through Stoke’s law (bigger sinks faster)
* Sedimentation takes time and is inaccurate. Laser diffraction is faster but also inaccurate.
By feel process (ribbon test)
Knead sample of moist soil into putty-like consistency, adding water if necessary.
Note its malleability, stickiness, and stiffness. Silt will feel smooth, sand will feel gritty and make a grinding noise.
To figure out clay amount, try to make a ribbon by squeezing between thumb and forefinger.
Structure of Mineral Soils
Soil structure is the spatial arragement of particles creating aggregations, pores, and channels.
When a mass of soil is excavated and gently broken apart, it breaks into large-scale structural units (peds) along natural zones of weakness.
Types of Soil Structure
A single-grained structure is made of particles that are not aggregated, for example, the loose sand in wind-blown dunes.
Some soils occur as large, cohesive masses of material and described as having a massive structural condition.
But most soils are some type of aggregation and can be characterized by shape, size, and distinctness (grade).
Spheroidal: granular and crumb structure consists of spheroidal aggregates in a loosely packed arrangement. <1-10mm diameter. Typical of many surface soils, usually A horizons. Granular is porous while crumb is very porous.
Platelike: platy structure is characterized by having thin horizontal sheet-like peds. Found in both surface and subsurface horizons. Developed as result of pedogenesis, parent materials, or compaction of clayey soil by heavy machinery. Common in E horizons.
Blocklike: blocky peds are irregular, roughly cubelike and range from 5-50mm diameter. Shape is not created independently but is molded by shapes of surrounding blocks. Angular blocky when the edges are sharp, subangular blocky when some rounding has occurred - usually in B horizons where they promote drainage, aeration, and root penetration.
Prismlike: columnar and prismatic structures have vertically oriented prisms or pillarlike peds, 150mm+ diameter. Columnar have rounded tops and mainly found in high sodium subsoils. Prismatic have angular flat tops and are associated with swelling types of clay, commonly in (semi)arid regions.
Size definitions come as fine, medium, coarse.
Degree comes as strong, moderate, weak, and refers to the distinctness of the peds.
Formation and Stabilization of Aggregates
Smaller aggregates are generally more stable than larger ones.
Macroaggregates (0.25-5mm) are made up of microaggregates (2-250μm). Microaggregates are made of tiny packets of clay and organic matter.
The hierarchy of aggregation may be demonstrated by gently crushing large aggregates.
Influencing Factors:
Physical-Chemical Processes:
Flocculation of clays: except in very sandy soils, soil aggregation starts with the flocculation (clumping together) of microscopic clay particles into floccules.
When clay platelets get close enough, compressed cations act as bridges holding their negative charges together, forming face-to-face stacks called clay domains.
Alternatively, positive charges on the edges of clay platelets can attract negative charges on flat planar surfaces, forming a random, open structure resembling a house of cards.Cations: multivalent cations (having more than one positive charge) neutralize clays negative ions allowing them to bond together.
Sodium (Na+) is a monovalent cation and is not strong enough to overcome clay platelets negative ions.
So the platelets repulse each other and are dispersed which clogs up the soil pores causing it to become gellike and highly undesirable for plant growth.
Biological Processes:
Insects move particles about and excrete them as pellets or casts.
Animals burrow which moves about particles and creates channels that break up clods, help define larger structural units, and serve as large conduits for new root growth.
Plant roots push particles together and form channels.
Plant root hairs and hyphae exude polysaccharides and other organic compounds (eg. glomalin) that are sticky and bind individual particles together and turn many microaggregates into macroaggregates.
Bacteria produce organic glues that intermix with clay on a very small scale.
Many glues resist water dissolution and so they enhance the formation of aggregates as well as ensure their stability over some time.
These processes are most notable in surface soils.
Organic Matter:
During aggregation, soil mineral particles become encrusted with bits of decomposed plant residue and other organic materials.
Polymers react with particles of silicate clays and iron/aluminum oxides, which helps to orient the clays into packets, forming bridges between particles and creating water-stable aggregates.
Tillage:
The good: If a soil is neither too wet nor dry, tillage can break large clods into natural aggregates, temporarily creating a soil that is conducive to young root growth. Tillage can also mix in organic matter and kill weeds.
The bad: Over time, tillage hastens the oxidative loss of organic matter, thus weakening aggregates. Aggregates can be smeared or crushed, especially when the soil is wet. This loses macroporosity and creates a puddled condition.
Organic matter acts like a sponge
Iron/Aluminum Oxides:
Mostly found in highly weathered soils in the tropics, they coat soils particles and cement aggregates, thereby preventing their breakdown when soil is tilled or wetted.
Compared to temperate soils, they have greater aggregate stability and do not depend on organic matter.
Tillage and Structural Management
For cultivated soils, the maintenance of stable surface soil structure is a major challenge. Desirable soil properties decline under long periods of tilled row-crop cultivation.
Tillage and Soil Tilth
Tilth is the physical condition of the soil in relation to plant growth. It depends on aggregates, bulk density, moisture content, aeration, water infiltration rate, drainage, and capillary water capacity.
Friable soils have clods that are not sticky or hard, but rather crumble easily to reveal constituent aggregates.
Soil friability is enhanced when the tensile strength of individual aggregates is higher than that of clods.
Increased organic matter content usually enhances friability and can enhance performance of clayey soils under tillage.
Optimal tillage timing depends on the optimal wet/dryness of the particular soil type.
Soil Crusting
Aggregates exposed at the surface are broken apart by water releasing clay particles. This causes a surface seal that is a thin, partially cemented layer with low permeability.
When the surface seal dries, it forms a hard crust. Seedlings can only emerge through cracks in the crust.
Soil Conditioners
Gypsum (calcium sulphate) is widely available and effective in improving soil quality, by reducing erosion and increasing water filtration and root penetration.
Organic polymers can stabilize soil structure.
Other soil conditioners include several species of algae that produce effective aggregate-stabilizing compounds.
Generally, soil tilth can be managed by minimizing tillage, timing traffic activities to optimum soil moisture content, mulching surface with organic residues, include sod crops in rotation, using cover crops, applying gypsum alone or with polymers.
Soil Density
Soil particle density (Dp) is the mass per unit volume of soil solids, not including pores. If 1 cubic meter of soil solids weighs 2.6Mg, the particle density is 2.6Mg/m3 or 2.6g/cm3.
Bulk density (Db) is the mass of a unit volume of dry soil, including both solids and pores.
High pore space = lower bulk density.
Bulk density can be determined by obtaining a known volume of water and drying it to remove the water, and weighing the dry mass. Gamma rays can also be used. There’s also a special coring instrument that can be used.
Several factors affect bulk density:
Soil texture: fine-textured soils (silt loams, clays, clay loams) have lower bulk densities than sandy soils. This is due to pore space and aggregation.
Depth in soil profile: deeper layers have higher bulk densities as a result of compaction, lower organic matter, less aggregation, and fewer biopores.
Management Practices
Increases in bulk density indicate a poorer environment for root growth, reduced aeration, water infiltration etc.
Forest Lands: O horizons in forests have low bulk densities. Timber harvesting compacts 20-40% of the forest floor, especially where logs are dragged or piled. Use cables to transport in the air.
Recreational activities such as trails and campsites increase bulk density. Placing a thick layer of wood chips on designated recreation zones/trails.Urban Soils: Trees planted for landscaping have to deal with highly compacted soils. To help: make the planting hole as large as possible, put a thick layer of mulch by the drip line but not the trunk, install a rigid, porous cover such as an iron grill, dig and backfill with loose, enriched soil, paths for future root growth.
Green Roofs: Soil mass must be minimized in order to design a cost-effective strong structure to carry it. Choose shallow rooted plants and soils with low bulk density.
Agricultural Land: Tillage increases bulk density by depleting organic matter and weakening soil structure. Minimize it by adding crop residues and rotating cultivated crops with a grass sod.
Machinery can cause compaction and create plow or traffic pans over repeated trips, especially on wet soils - dense zones immediately below the plowed layer.
Chisel-type plows can be used to subsoil - fracture and break up deep layers, temporarily enhancing root penetration.
Controlled traffic systems means all machinery is restricted to certin lanes.Certain plants alleviate deep subsoil compaction, such as species with thick taproots.
Soil Strength
Bulk density impacts soil strength and root growth.
Root penetration is limited by soil strength.
Soil strength can be measured with a penetrometer.
Water content is increased when soil is compacted to a higher bulk density and when fine soils dry out and harden.
The effect of bulk density on root growth is most pronounced when those soils are dry.Soil texture: Roots can more easily penetrate moist sandy soil than moist clayey soil at the same bulk density.
Pore Space of Mineral Soils
Measuring bulk density allows one to calculate pore space. The lower the bulk density, the higher the percent pore space: total porosity.
Macropores allow for movement of air and water, accomodate plant roots and tiny animals.
Macropores are generally found between peds - interped pores. They can also be created by roots or other organisms - biopores.
Micropores are usually filled with water. Even when dry, they are too small to allow air movement.
Larger micropores can accomodate root hairs and microbes, but smaller ones (ultramicropores or cryptopores or nanopores) are too small for even the smallest of bacteria.
Soil Properties for Engineering
Consistence = the ease with which a soil can be reshaped or ruptured. Degree of cementation by materials such as silica, calcite, or iron is to be considered.
A dry, clayey soil that cannot be crushed easily underfoot would be called very hard.
The same soil when wet would we easier to deform and called plastic.
Friable soils are moist clods that crumble easily.Consistency = how a soil resists rupture.
Bearing strength = the capacity of a soil mass to withstand stresses without rupturing.
Cohesive soils have 15%+ clay content. Strength is given by the electrostatic forces between clay and water, and the frictional resistance to movement between soil particles of all sizes.
The unconfined compression test is used to measure soil strength. A cylindrical sample of soil is placed vertically between two flat porous stone and a known force is applied until collapse.
The strength of noncohesive soils depends entirely on frictional forces.
Collapsible soils exhibit considerable strength with low in situ water contents, will lose strength suddenly when wet.
Thrixotropy is the sudden liquification of wet soil when subjected to vibrations eg. earthquakes.
Most collapsible soils are noncohesive and in (semi)arid regions.
The Proctor test guides efforts at compacting soil materials before construction. Soil is mixed to a given water content and compressed in a holder. The bulk density is measured. Repeated with increasing wter contents until a Proctor curve can be drawn. This indicated the maximum bulk density and soil water content that maximizes compactability.
Compressibility can be determined with a consolidation test, which measures how much volume is reduced by a given applied force.
Very sandy soils resist compression and make excellent soils for foundations.
The high porosity of clay give much greater compressibility, while soils consisting mainly of organic matter (peats) have the highest compressibilities and are unsuitable for foundations.
Expansive clays swell when wet and shrink when dry, especially smectite clay soils. They are not good for construction.
Atterberg Limits:
Clay soil is hard and rigid when dry, but becomes crumbly semisolid when a certain moisture content (shrinkage limit) is reached. If it contains expansive clays, the soil will swell in volume when the shrinkage limit is exceeded.
When soil water content exceeds the plastic limit, the soil will become malleable and plasticy.
The soil will remain in this plastic state until the liquid limit is exceeded, at which point it will transform into a viscous liquid.
Plasticity Index (PI) is the difference between plastic limit and liquid limit. Soils with PI greater than 25 are usuallt expansive clays.
The coefficient of linear extensibility (COLE) quantifies the expansiveness of a soil.
Questions
Q1: If you are investigating a site for proposed housing, how do you use soil colors to help predict where problems might be encountered?
A: Soil colours serve as indicators of drainage, water tables, and chemical composition.
Bright reds, browns, and yellows indicate well-aerated and drained conditions where iron is oxidized. Great for building foundations.
Gray, blue, or gleys indicate prolonged water saturation and heavy leaching. Causes wet basements and foundation shifting.
Dark colours indicate high organic matter content, which may increase compressibility. Can pose settlement issues, sinking.
Q2: One farm has mostly sandy loams and loamy sands, another farm has mostly clay loams and clays. List the potential advantages and disadvantages of each farm as per soil texture.
A: The sandy soils have excellent aeration, easy cultivation, and great water infiltration. However, they are drought-prone and low in nutrients.
The clayey soils have high water-holding capacity and nutrient retention. However, they have poor aeration and are prone to waterlogging.
Q3: Revisit your previous answer. Explain how soil structure in both surface and subsurface horizons might modify your opinion.
A: In the sandy soil, weak aggregation can be created by organic matter, which can slightly improve water and nutrient retention. However, massive structures worsen the droughty nature and may cause waterlogging.
In the clayey soils, there is a granular structure in the surface and a blocky/prismatic structure in the subsoil creates vital macropores. A dense sticky clay can therefore be transformed into a productive soil with good drainage.
Q4: Two different timber harvesting methods are being tested on clay loam surface soils. Initial bulk density was 1.1Mg/m3. One year after harvest, plot A changed to 1.48Mg/m3 and plot B to 1.29Mg/m3. Interpret these values with regard to the relative merits of systems A and B, and the likely effects on the soil’s function in the forest system.
A: A likely used traditional harvesting with heaving machines, dragging, and piling. This is likely because of the severe soil compaction. This crushes macropore, restricts root penetration, hampers gas exchange, and reduces water infiltration.
B exhibits a much lower increase, signifying that low-impact methods such as cable yarding or aerial suspension were used.
Q5: What are the textural classes of two soils, the first 15% clay and 45% silt, the second 80% sand and 10% clay.
A: First is loam, second is sandy loam.
Q6: For the aforementioned forest plot, the pore space of the surface soil changed. Was this change mostly in macropores or micropores?
A: Almost entirely in the macropores, because the micropores are already mostly filled with water.
Q7: Discuss the positive and negative impacts of tillage on soil structure. What is another physical consideration you would take into account in deciding whether or not to change from conventional to conservation tillage system?
A: Tillage can temporarily improve the upper layers and surface of the soil by breaking apart clods, incorporating surface residues, and controlling weeds. However, over time it leads to loss of organic matter and destroys aggregates. It can form plow pans and leaves soil vulnerable to erosion.
I would consider soil moisture and drainage/temperature. Residues left on the surface keep soils cooler and wetter in the spring.
Q8: What are the three best and worse things you can do to manage the soil structure in your home garden?
A: Best: Regularly add compost to feed microbes and stabilize aggregates, avoid working the beds when soil is wet to avoid compaction, use cover crops, mulches, or permanent pathways to protect the soil from crusting and erosion.
Worst: Tilling when the soil is too wet causing concrete-like clods, leaving bare soil exposed that causes crusting and surface sealing, stepping on beds instead of walkways.
Q9: What does the Proctor test tell an engineer about a soil, and why is this information important?
A: The relationship between a soil’s moisture content and its dry bulk density. It identifies the optimum moisture content that achieves the maximum dry bulk density. This is important for building as it ensures the subgrade is stable and can safely bear loads without breaking or settling unexpectedly.
Q10: In humid region with expansive soils, a homeowner had burst water pipes, wonky doors, and cracks in the walls. The house had no problems for 20 years. A consultant blamed the problems on a large tree that was planted near the house 10 years ago. Explain.
A: Expansive soils contain clays like smectite that swell when wet and shrink when dry. When the tree was planted, its root system began drawing massive amounts of water out of the clay soil during dry periods, causing the clay under one side of the house to dry out and shrink unevenly.
Chapter 8
The Colloidal Fraction
Colloids are highly reactive materials with electrically charged surfaces - which is an enormous surface area due to their size and shape.
General Properties
Size: extremely small, visible only with electron microscope. Less than 1μm in diameter.
Surface Area: large external surface area per unit mass, more than 1000 times the surface area of the same mass of sand particles.
Some silicate clays have internal surface area between layers of their page-like book structure.
Total surface area can be 800m2/g for clays with extensive internal surfaces.Adsorption of cations: Negative charged colloids attract thousands of cations that mostly exist in the hydrated state. Electrostatic attraction causes them to swarm near the colloid surface (they may be termed adsorbed or exchangeable in this state). Occassionally, one breaks away and move into the soil solution, with another cation immediately moving in to take its place. This is called cation exchange.
A colloid with adsorbed cations may be called ionic double layer.Adsorption of anions: some colloids have positive charges on their surfaces, attrating anions. While less than cations, we will see that this is an important function in acid subsoils.
Adsorption of water: colloids hold a large number of water molecules. This water is unavailable for plant uptake, but it plays a role in microbe survival.
Water adsorbed between clay layers can cause layers to move apart, making the clay more plastic and swelling its volume.
Types of Soil Colloids
Crystalline silicate clays are the dominant type in most soils. Their structure is like a book with sheets of closely packed and bonded oxygen, silicon, and aluminum atoms.
They are usually negatively charges but shapes, intensity of charge, stickiness, plasticity, and swelling behaviour may vary greatly.
Kaolinite, smectite.Noncrystalline silicate clays do not have the book-like sheet structure. They often form from volcanic ash. High amounts of both positive and negative charge and water-holding capacity.
They are malleable when wet (plasticity) but have a low degree of stickiness.
Allophane, imogolite.Iron and aluminum oxides are most important in highly weathered soils in humid regions. Mainly consist of iron/aluminum atoms with oxygen atoms. Some have crystalline structure, others occur as amorphous coatings on soil particles.
Low in plasticity and stickiness.
Net charge ranges from slightly negative to moderately positive.
gibbsite (aluminum oxide), geothite (iron oxide)Organic (humus) is especially important in upper parts of the soil profile. They’re neither minerals nor crystalline.
Composed of a variety of partially decomposed cell walls, bits of tissues, biomolecules.
Humus particles are often the smallest of soil colloids.
High water adsorbtion capacity.
No plasticity or stickiness.
No bearing strength.
Negative charge.
Layers and Structure
The most important silicate clays are called phyllosilicates because of their leaflike structure. They are composed of two types of sheets:
Tetrahedral sheets have two planes of oxygen with mostly silicon in the spaces between. The basic building block is one silicon atom surrounded by four oxygen atoms. It’s shaped like a pyramid, with the O2 at the apex called apical oxygen and the three at the base called basal oxygens. Basal O2 are shared with neighbor pyramids, so they’re connected.
Octahedral sheets have six oxygen atoms surrounding a central aluminum or magnesium atom. The sheet has variations:
- If three Mg2+ atoms are with six oxygens, its called trioctahedral sheet.
- If two Al3+ atoms are with six oxygens, its called dioctahedral sheet.
These sheets form silicate clays. Two or four may be stacked together, strongly bound by sharing oxygen atoms.
When different elements appear in the weathering solution, their cations may substitute for silicon, aluminum, and magnesium ions in the sheets as they crystallize. This process is called isomorphous substitution.
Isomorphous substitution is very important for providing positive and negative charges. For example, if an Mg2+ ion substitutes for Al3+ ion in dioctahedral sheet, the positive charges will not be enough to balance the negative charges of the oxygens, so the lattive is left with -1 net charge.
Organization of Minerals in Silicate Clays
Based on the number and arrangement of tetrahedral and octahedral sheets, crystalline clays are clased into two groups:
1:1 silicate clays : each layer has one tetra and one octa sheet.
2:1 silicate clays : each layer has one octa between two tetra.
1:1 Silicate Clays
Kaolinite is the most common.
The layers are held tightly together because the apical oxygen also forms a basal oxygen in the above sheet - hydrogen bonding.
This structure means that kaolinite has oxygen atoms on the bottom surface and a plane of hydroxyls on the upper surface.
Where the hydroxyl plane is exposed on the clay particle surface, it produces ± charges depending on soil pH, and it can react strongly with anions.
Because of hydrogen bonding, the structure is fixed and does not expand when wet.
Kaolinite crystals are usually hexagonal and larger than other clays.
Kaolinite has less plasticity, stickiness, shrinkage and swelling, water holding than 2:1 clays.
→ This means 1:1 dominated soils are better for agriculture as well as for use in roadbeds and foundations or for making bricks/ceramics.
1.1 silicate clays generally have small capacity to adsorb cations because of their fixed structure and smaller effective surface area of just the outer faces.
2:1 Silicate Clays
There are 4 groups of 2:1 silicate clays.
Expanding: smectite, vermiculite
Non-expanding: fine-grained micas (illite), chlorite
Smectite Group
They have flake-like crystals
High amount of mostly negative charges, mostly from Mg2+ ions substituted into Al3+ ions in octahedral sheet in isomorphous substitution.
→ these substitutions give an ability to adsorb cations that is 20-40 times higher than kaolinite.The structure has a layer of exposed oxygen at both top and bottom planes, so adjacent layers are loosely bound.
→ the internal surface area is accessible and the space attracts cations and water molecules.Flake-like smectite crystals form stacks with many ultramicropores. When wet, the water is adsorped into the pores and causes swelling. When dry, they often have wide cracks.
Smectite soils have high swelling, plasticity, stickiness, and cohesion, so they are difficult to cultivate.
Montmorillonite is the most common smectite in soil.
Vermiculite Group
Most commonly have dioctahedral sheets in 2:1.
The tetrahedral sheets have a lot of aluminum substituted in for silicon
→ the cation exchange capacity (CEC) exceeds that of all other silicate clays.Interlayer spaces usually have strongly adsorbed water, Al-hydroxy ions, and cations. These act as bridges to hold units together, instead of push apart.
They have limited expansion: less than smectites but more than kaolinite.
Mica Group
Fine-grained micas are more weathered and usually found in the clay fraction of soils.
The main source of charge is about 20% substitution of Al3+ for Si4+ in tetrahedral sheets → high net negative charge.
This charge attracts cations, particularly K+ which fits into holes between tetrahedral oxygen groups.
Mutual attraction for the K+ ions makes the layers strongly bind together, so fine-grained micas are nonexpansive with low capacity to adsorb water, plasticity, and stickiness.
Chlorites
Octahedral sites usually occupied by iron or magnesium rather than Al.
Often, a magnesium-dominated trioctahedral is sandwiched between 2:1 layers, so it can be said to have 2:1:1 structure.
Nonexpansive because of tight hydrogen bonding.
Colloidal properties are nonexpansive, low capacity to adsorb water, plasticity, and stickiness.
Structural Characteristics of Nonsilicate Colloids
Iron and Aluminum Oxides
Octahedral sheets that have been modified to have either Fe3+ or Al3+ in cation positions. So their structure does not have tetrahedral sheets nor silicon.
Isomorphous substitution rarely occurs, so they don’t have a big negative charge.
Their small amount of charge is caused by removal or addition of hydrogen ions at surface oxy-hydroxyl groups.
They are nonexpansive, with little stickiness, plasticity and cation adsorption, so they are stable for construction use.
The oxides can form coatings externally on silicate clays, or can appear as islands in the interlayer spaces. Both can highly alter colloidal behavior of the clay.
Gibbsite is the most common aluminum oxide in highly weathered soils.
Series of aluminum octahedral sheets linked by hydrogen-bonding, with a plain of hydroxyls exposed at both planes.
Goethite is a common iron oxide clay in temperate regions.
Goethite and ferrihydrite give soils a yellow-brown color.
Hematite gives a redder color.
Humus
Made of noncrystalline heterogeneous organic substances with very variable chemical composition but mostly C, O, H, N in order of decreasing percentage.
Most humus colloids are tiny bits of partially decomposed plant tissue, cell walls, and films of biomolecules.
→ These contain ring structures and carbon chains with chemically active groups of atoms that are responsible for the high amount of charge in humus.It attracts and adsorbs both cations and anions, but the negative sites always outnumber positive.
Very large net negative charge.
Can adsorb very large amounts of water per unit mass.
Genesis and Distribution of Soil Colloids
Genesis
Alteration and recrystallization are the two distinct weathering processes that form silicate clays.
Alteration: example - muscovite mica → fine-grained mica
Muscovite is a dioctahedral 2:1 primary mineral with nonexpanding crystal structure. It is weathered and broken down in size to colloidal range. Some potassium is lost while silicon and cations are added from weathering solutions → Results in less rigid crystal structure and new sites available that were once held by potassium.
It keeps the 2:1 type structure but has been altered in the process.
Recrystallization: complete breakdown of crystal structure and recrystallization of products of this breakdown. Needs much more intense weathering than alteration requires.
Example - kaolinte from solutions containing aluminum and silicon from the breakdown of 2:1 primary minerals.
It’s possible to get more than one clay from a primary mineral. It depends on weathering conditions and ions present in the weathering solution.

Several silicate clays can be found in close association in many soils. So some colloids are intermediate, like a mixed layer or interstratified clay mineral such as fine-grained mica-vermiculite.
Creation of iron and aluminum oxides
Iron oxides often produced by weathering of iron-containing primary silicate minerals, or by precipitation of iron from soil solutions.
In aerated weathering, Fe2+ quickly oxidizes to Fe3+. By reacting with water and oxygen atoms, Fe3+ forms stable oxides and hydroxides (eg. goethite, hematite).
Aluminum oxides are produced in strong weathering environments where acid leaching quickly removes Si.
During weathering, hydrogen ions replace K+ and Mg2+ → causing the structure to break down and release Si and Al.
The released Al from iron-rich rocks (eg. gabbro/basalt) can form gibbsite directly. Or, weathering of light-colored rocks (eg. granite/gneiss) first produces 1:1 silicate minerals which upon further weathering can create gibbsite.
So, gibbsite is extremely stable and represents a very advanced stage of weathering. Al(OH)3
Creation of allophane and imogolite
Little is known about their formation.
Associated with PM of volcanic origin, but also formed by igneous rock.
They are poorly crystalline and have good capacity to strongly retain anions, as well as to bind with humus.
Creation of humus
Breakdown of plant residues by microbes → stabilization of plant/microbial materials by interaction with other soil components → dark, colloidal organic material called humus.
Distribution
Soils have mixtures of different colloids which also varies between horizons because genesis depends on climate influences, profile conditions, and nature of parent material.
Well-drained, highly weathered soils in warm/humid/subhumid tropics are dominated by kaolinite with iron/aluminum oxides.
Less intensely weathered soils in temperate regions have more smectite, vermiculite, and fine-grained mica groups.
Soils with PM high in mica will form fine-grained micas such as illite.
Soils with PM high in metallic cations or subject to restricted drainage will form smectite.
Sources of Charges
Two major sources: 1) Permanent charge imbalance by isomorphous substitution. 2) Hydroxyls on the surface release or accept H+ ions, giving ± charges depending on soil pH.
1) Constant Charges
Negative: Where a lower-charged ion substitutes in for a higher-charged ion → Mg2+ for Al3+ that occurs in aluminum-dominated dioctahedral sheets of smectite, vermiculite, chlorite clays.
→ Al3+ for Si4+ in tetrahedral sheet, common in fine-grained micas, vermiculite, smectites.Positive: When the substituting cation has a higher charge.
→ Al3+ for Mg2+ in trioctahedral sheet.
2) pH Dependent Charges
Negative: Higher pH = negative charge and vice-versa.
Positive: protonation is the attachment of H+ to OH groups in acidic soils.
Cation Exchange Reactions
Cation exchange capacity (CEC) is the centimoles of positive charge per kg: cmolc/kg.
If a hydrated anion replaces another at a positively charged colloid site, it is anion exchange.
All colloids in a soil that are capable of holding exchangeable cations or anions are called the exchangeable complex.
Governing laws of cation exchange:
Reversability.
Charge equivalence eg. two H+ are required to replaced one Ca2+.
Ratio law ie. the ratio on the colloids will be the same as in the solution, equilibrium.