Lab Notes


Day 15:




  1. Subnet the 192.168.5.0/24 network to provide sufficient addressing for each LAN.

(Also, the point-to-point connection between R1 and R2).


lan 2 uses /25

network is 192.168.5.0

broadcast is 192.168.5.127

lan 1 uses /26
Network 192.168.5.128

Broadcast 192.168.5.191


lan 3 uses /28

network 192.168.5.192

broadcast 192.168.5.207


lan 4 uses /28

network 192.168.5.208

broadcast 192.168.5.223 (224 is the next network address)

  1. Assign the first usable address to the PC in each LAN.


  1. Assign the last usable address to the router's interface in each LAN.


  1. Configure static routes on each router so that all PCs can ping eachother.













day 16:















Day 16’s Lab


1. Configure the correct IP address/subnet mask on each PC.

Set the gateway address as the LAST USABLE address of the subnet.


  • 10.0.0.62

  • 10.0.0.126

  • 10.0.0.190


2. Make three connections between R1 and SW1.

Configure one interface on R1 for each VLAN.

Make sure the IP addresses are the gateway address you configured on the PCs.


  • R1 →

  • int g0/0

  • ip address 10.0.0.62 255.255.255.192

  • no shutdown

  • do sh ip int br


3. Configure SW1's interfaces in the proper VLANs.

Remember the interfaces that connect to R1!

Name the VLANs

(Engeering, HR, Sales)


  • Sw 1 →

  • int range g0/1, f3/1,f4/1

  • switchport mode access

  • switchport Access vlan 10


  • vlan 10

  • Name Engineering









Day 17’s Lab



1. Configure the switch interfaces connected to PCs as access ports in the correct VLAN.


  • SW1

  • int range f0/1-2

  • sw mode access

  • sw access vlan 10


2. Configure the connection between SW1 and SW2 as a trunk, allowing only the necessary VLANs.


  • SW1

  • int g0/1

  • switchport mode trunk

  • switchport trunk allowed vlan 10,30

  • sw trunk native vlan 1001

  • do show vlan brief


  • sw2

  • int g0/1

  • sw mode trunk

  • sw trunk allowed vlan 10,30

  • sw trunk native vlan 1001

  • do show vlan brief


Configure an unused VLAN as the native VLAN.

Make sure all necessary VLANs exist on each switch


  • SW2

  • show interfaces trunk

  • look for Vlan’s allowed and active in management domain (vlan 30 isn’t allowed yet)

  • vlan 30


3. Configure the connection between SW2 and R1 using 'router on a stick'.

Assign the last usable address of each subnet to R1's subinterfaces.


  • SW2

  • int g0/2

  • sw mode trunk

  • sw trunk allowed vlan 10,20,30

  • sw trunk native vlan 1001


  • R1

  • Int g0/0

  • no shutdown

  • int g0/0.10

  • Encapsulation dot1q 10 → 10 is the vlan number

  • ip address 10.0.0.62 255.255.255.192












Day 18’s Lab


1. Replace the ROAS configuration on R1-SW2 with a point-to-point Layer 3 connection.

Use the IP addresses given in the network diagram.

Configure a default route on SW2, with R1's G0/0 interface as the next hop.


  • R1

  • Show running-config →

  • show ip interface brief → look at subinterfaces and remove them

  • No int g0/0.10 → repeat for .20 and .30

  • int g0/0

  • ip address 10.0.0.194 255.255.255.252


  • SW2

  • show run → look at g1/0/2 and see that it requires encapsulation dot1q

  • default interface g1/0/2

  • show run → make sure it’s just got ! and all the configurations are removed


  • int g1/0/2

  • no switchport

  • ip address 10.0.0.193 255.255.255.252

  • exit


  • back to sw2

  • ip routing

  • do show ip route →

  • ip route 0.0.0.0 0.0.0.0 10.0.0.194


2. Configure SVIs on SW2, one for each VLAN.

Assign the last usable IP address of each subnet to the appropriate SVI.


  • SW2

  • Do show vlan brief → make sure Vlan’s exist

  • interface vlan 10 → ip address 10.0.0.62 255.255.255.192

  • interface vlan 20 → 10.0.0.126 255.255.255.192

  • interface vlan 30 → 10.0.0.190 255.255.255.192

  • Do show ip interface brief → make sure they are all Up/Up







Day 19:


1. Configure the switchports connecting switches as trunk ports.

Disable DTP on the ports.

Confirm the administrative and operational mode of each interface.


  • SW1

  • Do show interface g0/1 Switchport → look at administrative mode: static access and negotiation of trunking: on (DTP frames are being sent out)

  • Switchport mode trunk

  • switchport nonegotiate → This disables negotiation of trunking/DTP (dynamic desirable)


  • SW2

  • int range g0/1-2

  • switchport mode trunk

  • switchport nonegotiate

  • do show interface g0/1 switchport


2. Configure SW1 in VTP domain CCNA.

Create VLANs 10, 20, and 30 on SW1.

Have SW2 and SW3 added VLANs 10, 20, and 30?


  • SW1

  • do show VTP status

  • VTP domain CCNA

  • vlan 10 → vlan 20 → vlan 30


3. Configure SW2 in VTP transparent mode.

Add VLAN40 to SW2.

Is VLAN40 added to the VLAN database of SW1/SW3?


  • SW2

  • vtp mode transparent

  • vlan 40

  • do show vtp status (revision number is now 0)


4. Configure SW3 in VTP client mode.

Try to configure VLAN50 on SW3. Is it added?


  • VTP mode client

  • vlan 50


5. Configure all switchports connected to hosts in the correct VLAN.

Manually configure them as access ports.

Is DTP still enabled on the switchports?


  • sw3

  • int f0/1

  • do sh int f0/1 switchport

  • sw mode access

  • sw access vlan 10

  • do sh int f0/1 switchport









Day 21


1. Use the CLI to check the current STP topology. What is the current root bridge?

What is the STP role/state of each port on each switch?


  • SW1

  • show spanning-tree → see that sw2’s int has the root bridfe


  • SW2

  • show spanning-tree → in Root ID it says “This bridge is the root”

  • all ports are in a designated state on SW2


2. Configure SW1 as the primary root for VLAN1 and the secondary root for VLAN2.

Configure SW2 and the primary root for VLAN2 and the secondary root for VLAN1.

What is the STP role/state of each port on each switch now?


  • SW1

  • spanning-tree vlan 1 root primary

  • spanning-tree vlan 2 root secondary


  • SW2

  • spanning-tree vlan 1 root secondary

  • spanning-tree vlan 2 root primary


  • Show spanning-tree and look at it on per vlan basis


3. Increase the VLAN1 cost of SW4's F0/2 interface to 100.

Does SW4 select a different root port? Why/why not?


  • show spanning-tree vlan 1

  • int f0/2

  • spanning-tree vlan 1 cost 100


4. Increase the VLAN1 port priority of SW1's F0/1 to 240.

Does SW3 select a different root port? Why/why not?


  • SW3

  • show spanning-tree vlan 1

  • spanning-tree vlan 1 port-priority 240

  • (it shouldn’t affect it bec


5. Configure PortFast and BPDU Guard on the F0/3 interfaces of SW3/SW4.


  • int f0/3

  • spanning-tree portfast

  • spanning-tree bpduguard enable










Day 22


configure the correct link type

int f0/24 → spanning-tree portfast (edge)

int range f0/1-2 → spanning-tree link-type point-to-point











Day 23


1. Configure Layer 2 EtherChannel between ASW1 and DSW1 using LACP.

Configure it as a trunk.


  • ASW1

  • Show spanning-tree

  • int range g0/1-2

  • channel-group 1 mode active

  • int p0/1

  • switchport mode trunk

  • show etherchannel summary


  • DSW1

  • int range g1/0/3-4

  • channel-group 1 mode active

  • int p0/1

  • switchport mode trunk

  • switchport trunk encapsulation dot1q

  • show etherchannel summary

  • show interface trunk


2. Configure Layer 2 EtherChannel between ASW2 and DSW2 using PAgP.

Configure it as a trunk.


  • ASW2

  • int range g0/1-2

  • channel-group 1 mode desirable

  • int p0/1

  • switchport mode trunk


  • DSW2

  • int range g1/0/3-4

  • channel-group 1 mode desirable

  • int p0/1

  • switchport trunk encapsulation dot1q

  • switchport mode trunk

  • show etherchannel summary


3. Configure Layer 3 EtherChannel between DSW1 and DSW2 using static EtherChannel


  • DSW2

  • int range g1/0/1-2

  • no switchport

  • channel-group 2 mode on

  • int p0/2

  • ip address 10.0.0.2 255.255.255.252


  • DSW1

  • int range g1/0/1-2

  • no switchport

  • channel-group 2 mode on

  • int p0/2

  • ip address 10.0.0.1 255.255.255.252

  • do show etherchannel summary


4. Configure routes to allow the PCs to reach SRV1.


  • DSW1

  • Do show ip route

  • ip routing

  • ip route 172.16.2.0 255.255.255.0 10.0.0.2


  • DSW2

  • ip routing

  • ip route 172.16.1.0 255.255.255.0 10.0.0.1

  • do show ip route


5. What is the default EtherChannel load-balancing method used on each switch?


  • show etherchannel load-balance


6. Configure the switches to load-balance based on source and destination IP addresses.


  • ASW1

  • port-channel load-balance src-dst-ip

  • do show etherchannel load-balance














day 24:



1. Check the routing tables of R1 and R2.

  • show ip route

Which dynamic routing protocol is Enterprise A using?

  • ospf (in routing legend)


2. Configure floating static routes on R1 and R2 that

allow PC1 to reach SRV1 if the link between R1 and R2 fails. → (use isp A)

Do the routes enter the routing tables of R1 and R2? → no


  • Use ISP A

  • #R1

  • ip route 10.0.2.0 255.255.255.0 203.0.113.1 ?

  • set the distance (which is AD) to 111


  • R2 needs a return route

  • ip route 10.0.1.0 255.255.255.0 203.0.113.5 111


3. Shut down the G0/2/0 interface of R1 or R2.

Do the floating static routes enter the routing tables of R1 and R2?

Ping from PC1 to SRV1 to confirm.









day 25:


2. Configure a loopback interface on each router (1.1.1.1/32 for R1, 2.2.2.2/32 for R2, etc.)

Watch the video if you don't know how to do this!


  • interface loopback 0

  • ip address 1.1.1.1 255.255.255.255


3. Configure EIGRP on each router.

Disable auto-summary.

Enable EIGRP on each interface (including loopback interfaces).

Configure passive interfaces where appropriate (including loopback interfaces).


  • R4

  • Router EIGRP 100 (it’s the AS number)

  • Network 0.0.0.0 255.255.255.255

  • No auto-summary

  • passive-interface g0/0, l0/0

  • Do sh ip eigrp neighbors

  • do show ip route eigrp

  • do show ip eigrp topology


4. Configure R1 to perform unequal-cost load-balancing

when sending network traffic to 192.168.4.0/24

  • do show ip eigrp topology

  • variance 2






day 26


1. Configure the appropriate hostnames and IP addresses on each device. Enable router interfaces.

(You don't have to configure ISPR1)

  • blah blah


2. Configure a loopback interface on each router (1.1.1.1/32 for R1, 2.2.2.2/32 for R2, etc.)

  • r4

  • int l0

  • ip addr 4.4.4.4 255.255.255.255

  • do show ip int l0


3. Configure OSPF on each router.

Enable OSPF on each interface (including loopback interfaces).

(Do not enable OSPF on R1's Internet link)

Configure passive interfaces where appropriate (including loopback interfaces).


  • R4#

  • router ospf 4

  • network 0.0.0.0 255.255.255.255 area 0

  • passive-interface g0/0

  • passive-interface l0


  • R1#

  • int l0

  • ip add 1.1.1.1 255.255.255.255

  • router ospf 1

  • network 10.0.12.0 0.0.0.3 area 0

  • network 10.0.0.13.0 0.0.0.3

  • network 1.1.1.1 area 0

  • passive-interface l0


4. Configure R1 as an ASBR that advertises a default route in to the OSPF domain.


  • default-information orginate

  • ip route 0.0.0.0 0.0.0.0 203.0.113.2

  • show ip protocols (router id loopback id + ASBR)

  • show ip ospf database


5. Check the routing tables of R2, R3, and R4. What default route(s) were added?






day 27

1. Configure the appropriate hostnames and IP addresses on each device. Enable router interfaces.

(You don't have to configure ISPR1)


2. Configure a loopback interface on each router (1.1.1.1/32 for R1, 2.2.2.2/32 for R2, etc.)

  • int l0

  • ip addr 1.1.1.1 255.255.255.255


3. Enable OSPF directly on each interface of the routers.

Configure passive interfaces as appropriate.


  • R1

  • interface range g0/0, f1/0, l0

  • ip ospf 1 area 0

  • do show ip protocols


  • router ospf 1

  • passive-interface l0


4. Configure the reference bandwidth on each router so a FastEthernet interface

has a cost of 100.


  • auto-cost reference-bandwidth 10,000 (reference bandwidth/int bandwidth =cost)

  • do show ip ospf interface → look for cost


5. Configure R1 as an ASBR that advertises a default route in to the OSPF domain.


  • default-information orginate

  • ip route 0.0.0.0 0.0.0.0 203.0.113.2








day 28 (not done)


The network has been pre-configured (IP addresses, OSPF)


1. The connection between R1 and R2 has been newly added.

-Configure the serial connection between R1 and R2 (clock rate of 128000).

-Configure OSPF on R1 and R2.


2. Only R3 has a route to 10.0.2.0/24. Why? Fix the problem.


3. R2 and R4 won't become OSPF neighbors with R5. Why? Fix the problem.


4. PC1 and PC2 can't ping the external server 8.8.8.8. Why? Fix the problem.


5. Examine the LSDB. What LSAs are present?