Microbiology Lab: Catalase Testing, Media Preparation, and Autoclave Procedures

Experiment 11: Metabolism of Microorganisms - Catalase Test

  • Objective: To identify the presence of the enzyme catalase in microorganisms as part of metabolic analysis.

  • Principle: Catalase is an enzyme that catalyzes the decomposition of hydrogen peroxide into water and oxygen. The reaction is represented by the following chemical equation:     2H2O2→2H2O+O22H_2O_2 \rightarrow 2H_2O + O_2

    • Substrate: Hydrogen Peroxide (H2O2H_2O_2).

    • Products: Water (2H2O2H_2O) and Oxygen gas (O2O_2).

  • Materials:

    • Bacterial Cultures: E.coli and S. aureus.

    • Reagent: 3%3\% Hydrogen peroxide solution.

    • Tools: Glass slides, wire loop, Bunsen burner.

    • Solvent: Distilled water.

  • Procedure:

    • a. Prepare a smear of the provided bacteria on separate glass slides.

    • b. Add 3 or 3 drops (per transcript) of hydrogen peroxide to the bacterial smears.

    • c. Observe for the presence of catalase, which is indicated by the evolution of bubbles (the visible release of gas).

    • d. Record results. The gas evolved in this specific chemical reaction is Oxygen (O2O_2).

Experiment One: Preparation of Nutrient Agar

  • Objective: To prepare and sterilize nutrient agar (NA) media for microbiological use.

  • Materials:

    • Nutrient agar power (as spelled in transcript).

    • Equipment: Bunsen burner, Mettler balance, Flat bottom flask, Autoclave.

    • Supplies: Sterile petri dish, Distilled water.

  • Preparation Procedure:

    • Concentration Formula: Dissolve 28 kg28\,kg of NA power into 1 liter1\,liter of distilled water.

    • Quantity Calculation: For a volume of 20 ml20\,ml, weigh out the appropriate proportionate quantity of NA power.

    • Mixing: Combine the power and water, mixing until the substance is evenly dispersed.

    • Sterilization: Autoclave the mixture for 15 minutes15\,minutes at a temperature of 121∘C121^{\circ}C.

Detailed Standard Operating Procedure for Autoclaving

  • 1. Initial Setup:

    • Remove the basket from the autoclave chamber.

    • Pour approximately 1.5 liters1.5\,liters of water into the autoclave. Ensure the water level is sufficient to cover the heating element.

    • Replace the basket into the chamber.

  • 2. Loading:

    • Pack the basket with the items (media, bottles, etc.) intended for sterilization.

  • 3. Sealing:

    • Place the lid in the correct position.

    • Fasten the wing nuts. Note: They do not need to be screwed down excessively hard.

  • 4. Controls and Safety:

    • Set the adjustable safety mechanism.

    • Close the drain cock.

    • Fully open the air cock (to allow air to escape).

  • 5. Heating Phase:

    • Switch on the electric current.

    • Wait for the water to reach a boil, which typically takes about 10 minutes10\,minutes.

    • Allow steam to issue from the air cock for a full 5 minutes5\,minutes to ensure all air is displaced. This is critical because the presence of residual air lowers the temperature achieved at a given pressure.

    • Close the air cock after the 5 minutes5\,minutes of steam venting.

  • 6. Pressurization and Sterilization:

    • Wait for the internal pressure to reach 103 kpa103\,kpa, which takes approximately 5 minutes5\,minutes. At this point, steam will begin to escape from the safety valve.

    • Maintain this state for a sterilization duration of 15 minutes15\,minutes (specifically required for media bottles).

  • 7. Shutdown and Cooling:

    • At the conclusion of the sterilization time, switch off the electric current completely.

    • Critical Warning: Do not open either the drain cock or the air cock immediately.

    • Wait until the internal pressure falls to exactly 00.

  • 8. Unloading:

    • Once pressure is at zero, open the air cock.

    • Unfasten the wing nuts and remove the lid.

    • Carefully remove the sterilized items from the chamber.