Raman Spectroscopy Study Notes
Raman Spectroscopy
Theory of Raman Spectroscopy
Basic Principle:
- Raman spectra are obtained by using a high intensity laser source.
- This laser can be monochromatic, visible, or near-infrared (IR) light.
Scattering Types
Rayleigh Scattering:
- Described as elastic scattering of light.
- No change in wavelength occurs during this process.Raman Scattering:
- Involves inelastic collisions.
- This collision results in a change in wavelength between the incident and scattered light.
- Emitted light can have either longer or shorter wavelengths than the incident light.
Energy Transfer Mechanism
When a radiation beam with energy
- Excites a molecule from the ground vibrational state () to a higher “virtual state.”
- On relaxing back to ground state, a photon with the same energy as the excitation photon can be emitted.
- If it relaxes to the first excited vibrational state ():
- The emitted photon energy changes.
Stokes and Anti-Stokes Peaks
Stokes Scattering:
- Equation:
- Result: The photon emitted has less energy than the excitation photon, thus appears at a lower frequency compared to Rayleigh peak.
- The intensity and position of the peak are determined by the vibrational transition of the molecule.Anti-Stokes Scattering:
- When a sample is already in the first excited state () and relaxes to the ground state (), it emits a photon with:
- Equation:
- Result: This photon has more energy than the excitation photon, hence appears at a higher frequency than the Rayleigh peak.
- The shift's magnitude is determined by the vibrational transition.Intensity Difference:
- Anti-Stokes peaks typically have lower intensity compared to Stokes peaks due to a lower population of vibrationally excited states at room temperature.
Raman Shift Scale
Definition:
- The wavelength of the excitation radiation is defined as 0 on the Raman shift scale.
- It’s important to note that the Raman shift is independent of the excitation frequency; it corresponds to the frequency of the vibrational mode observed.
- Various vibrational modes can be Raman-active, resulting in multiple observable peaks.
Raman Active vs. IR Active Modes
IR Active Requirement:
- For a vibrational mode to absorb infrared radiation, there must be a change in the dipole moment due to vibrational motion.
- Types of dipole moments:
- Permanent Dipole Moment: Exists in polar molecules (e.g., HCl).
- Dynamic Dipole Moment: Induced by vibration, generally smaller than permanent dipoles.Dynamic Dipole Moment Mechanism:
- Depends on bond length and the amount of charge transfer, sensitive to the inter-nuclear distance.
- Variations in intermolecular distance during vibrations change the dipole moment, creating dynamic dipoles.
Vibrational Selection Rules
Electric Dipole Moment:
- Must change due to atomic displacement; such vibrations are termed infrared-active.
- Molecules need not have a permanent dipole; any change from zero is sufficient for IR activity.
- Some vibrational modes (e.g., symmetric stretches of homonuclear diatomics) do not affect the dipole moment; these are infrared inactive.Identifying IR Active Molecules:
- From the following molecules:
- N2, CO2, OCS, H2O, CH2=CH2, C6H6
- All except N2 have at least one vibrational mode that changes the dipole moment.
- For instance, CO2's symmetric stretch is IR inactive because it does not alter the dipole moment.
Polarizability Change Requirement:
- A change in polarizability due to molecular vibrations is necessary for Raman activity.
- During vibration, the nuclei's control over electron distribution causes the polarizability to vary.
- In harmonic approximation, the specific selection rule is noted as .
Example of Raman Activity
CO2: Symmetric stretch alters polarizability (Raman active) but does not affect dipole moment (not IR active).
Mutual Exclusion Principle
Definition:
- If a molecule posseses a center of symmetry, no vibrational modes can be both Raman active and infrared active.
- It is possible for the mode to be inactive in both cases, simplifying the judgment of vibrational mode activity.
- This principle applies to molecules like CO2 but does not apply to H2O or CH4 as they lack a center of symmetry.
- Group theory is essential for accurately predicting a mode's IR or Raman activity.
Comparison of IR and Raman Spectroscopy
Spectral Appearance:
- Both techniques yield similar spectral profiles, but relative intensities of bands may differ significantly between the two methods.
Raman Instrumentation
Components of a Raman Spectroscopy setup include:
1. Sample cell
2. Wavelength selector
3. Radiation transducer
4. Computer data system
5. Laser source
Laser Types and Wavelengths
Examples of Laser Sources:
- Argon ion: 488.0 or 514.5 nm
- Krypton ion: 530.9 or 647.1 nm
- Helium-neon: 632.8 nm
- Diode: 785 or 830 nm
- Nd-YAG: 1064 nm
Sample Handling in Raman Spectroscopy
Proper alignment and handling of the sample under the laser beam are crucial for effective measurement and analysis (illustration included).
Advantages of Raman Spectroscopy
Applicable to various sample types including inorganic, organic, and biological.
- For Inorganics:
- Superior to IR as it allows for the study of aqueous solutions.
- Metal-ligand bond vibrations are typically in the range of 100 - 700 , challenging to analyze via IR.
- For Organics:
- Effective for studying functional groups that lack IR activity, such as C=C stretches and low frequency modes.
- Provides complementary data to IR spectra.
Quantitative Applications
Raman offers fewer peaks, reducing the chance of peak overlaps.
No windows in the Raman sampling device are prone to degradation from moisture or sample interference.
The small spot size of the laser allows analysis of very small samples and the possibility of compositional mapping via Raman microprobe.
Applications in Synthetic Diamonds
Low-Temperature Diamond Synthesis:
- Created at 440 through the reduction of dense CO2 with metallic sodium.