Prelecture 6 reading
9.3: Mechanics of a single-fiber contraction
The force exerted on an object by a contracting muscle is known as muscle tension, and the force exerted on the muscle by an object (usually its weight) is the load.
Muscle tension and load are opposing forces.
Whether a fiber shortens depends on the relative magnitudes of the tension and the load.
For muscle fibers to shorten and thereby move a load, muscle tension must be greater than the opposing load.
When a muscle develops tension but does not shorten or lengthen, the contraction is said to be an isometric contraction.
Such contractions occur when the muscle supports a load in a constant position or attempts to move an otherwise supported load that is greater than the tension developed by the muscle.
During an isometric contraction, the bound cross-bridges exert a force on the thin filament but they are unable to move it. Rather than the filaments sliding, the rotation during the power stroke is absorbed by elastic elements within the sarcomere and muscle.
A contraction in which the muscle changes length while the load on the muscle remains constant is an isotonic contraction.
These can be associated with either shortening or lengthening of a muscle.
When tension exceeds the load, shortening occurs and it is referred to as concentric contraction
When an unsupported load is greater than the tension generated by cross-bridges, the result is an eccentric contraction. In this situation, the load pulls the muscle to a longer length in spite of the opposing force produced by the cross-bridges.
Activated muscle fibers can lengthen only as a consequence of external forces being applied to them.
In the absence of external lengthening forces, a fiber will shorten only when stimulated.
During a concentric isotonic contraction, the cross-bridges bound to actin rotate through their power stroke, causing shortening of the sarcomeres.
During a lengthening contraction, the load pulls the cross-bridges backward toward the Z lines while they are still bound to actin and exerting force.
The mechanical response of a muscle fiber to a single action potential is known as a twitch.
Following an action potential, there is an interval of a few milliseconds known as the latent period before the tension in the muscle fiber begins to increase.
During this period, the processes associated with excitation-contraction coupling are occuring.
The time interval from the beginning of tension development at the end of the latent period to the peak tension is the contraction time.
The total duration of a contraction depends in part on the time that cytosolic Ca2+ remains elevated so that cross-bridges can continue to cycle.
The latent period for an isotonic twitch contraction is longer than that in an isometric twitch contraction.
At heavier loads: The latent period of an isotonic twitch is longer, the velocity of shortening is slower, and the distance shortened is less.
When the initial shortening velocity (slope) of a series of isotonic twitches is plotted as a function of the load on a single fiber, the result is a hyperbolic curve.
The shortening velocity is maximal when there is no load, and zero when the load is equal to the maximal isometric tension.
At loads greater than the maximal isometric tension, the fiber will lengthen at a velocity that increases with the load.
The unloaded shortening velocity is determined by the rate at which individual cross-bridges undergo their cyclical activity, which is a function of the maximum intrinsic rate of the myosin ATPase enzyme.
Increasing the load on a cross-bridge, however, slows its forward movement during the power stroke. This reduces the overall rate of ATP hydrolysis and, thus, decreases the velocity of shortening.
Because a single action potential in a skeletal muscle fiber lasts only 1 to 2 msec but the twitch may last for 100 msec or more, it is possible for a second action potential to be initiated during the period of mechanical activity.
When a stimulus is applied before a fiber has completely relaxed from a twitch, it induces a contractile response with a peak tension greater than that produced in a single twitch.
If the interval between stimuli is shortened further, the resulting peak tension is even greater.
A maintained contraction in response to repetitive stimulation is known as a tetanus.
As the frequency of action potentials increases, the level of tension increases by summation until a maximal fused tetanic tension is reached, beyond which tension no longer increases even with further increases in stimulation frequency.
This maximal tension is about 3-5 times greater than the isometric twitch tension.
During a tetanic contraction, the successive action potentials each release Ca2+ from the sarcoplasmic reticulum before all the Ca2+ from the previous action potential has been pumped back into the sarcoplasmic reticulum.
This results in a persistent elevation of cytosolic Ca2+ concentration, which prevents a decline in the number of available binding sites on the thin filaments.
More binding sites remain available and many more cross-bridges become bound to the thin filaments.
The springlike characteristic of the protein titin, which is attached to the Z line at one end and the thick filaments at the other, is responsible for most of the passive elastic properties of relaxed muscle fibers.
With increased stretch, the passive tension in a relaxed fiber increases, not from active cross-bridge movements but from elongation of the titin filaments.
If the stretched fiber is released, it will return to an equilibrium length.
The amount of active tension a muscle fiber develops during contraction can also be altered by changing the length of the fiber.
If you stretch a muscle fiber to various lengths and tetanically stimulate it at each length, the magnitude of the active tension will vary with length.
The length at which the fiber develops the greatest isometric active tension is termed the optimal length.
When a muscle fiber length is 60% of the optimal length or shorter, the fiber develops no tension when stimulated.
As the length is increased from this point, the active isometric tension at each length is increased up the a maximum at the optimal length.
Further lengthening leads to a decrease in action tension, where at lengths of 175% of the optimal length or greater, the fiber develops no active tension.
When most skeletal muscle fibers are relaxed, passive elastic properties keep their lengths near the optimal length for force generation.
Stretching a relaxed muscle fiber pulls the thin filaments past the thick filaments, changing the amount of overlap between them.
Stretching a fiber to 175% of the optimal length pulls the filaments apart to the point where there is no overlap, and can be no cross-bridge binding.
As the fiber shortens towards the optimal length, more and ore filament overlap occurs and the tension developed upon stimulation increases in proportion to the increased number of cross bridges in the overlap region
The tension declines at lengths less than the optimal lengths because the overlapping sets of thin filaments from the opposite ends of the sarcomere may interfere with the cross-bridges ability to bind and exert force, and also because the Z lines collide with the ends of the thick filaments, creating an internal resistance to shortening.
9.6: Whole muscle contraction