CIV 3102 Module 05: Infiltration, Evaporation, and Transpiration Study Guide

Introduction to Soil Water and Subsurface Zones

  • Soil Water Zones: Subsurface water is categorized into two primary vertical zones:

    • Unsaturated Zone (Vadose Zone): Located immediately below the land surface, containing both water and air in the pores. It include the soil water zone and the intermediate zone.

    • Capillary Fringe: A transition region just above the water table where water is drawn upward from the saturated zone by capillary action.

    • Saturated Zone: The area where all soil pores are completely filled with water. Its upper boundary is known as the water table.

  • Flow Components Above the Water Table:

    • Precipitation: The primary input of water from the atmosphere.

    • Infiltration: The process by which water enters from the surface into the soil.

    • Irrigation: Artificial application of water to the soil.

    • Evapotranspiration: The loss of water from the soil through evaporation and plant transpiration.

    • Surface Runoff: Water that does not infiltrate and flows over the land surface.

    • Percolation: The downward movement of water through the unsaturated zone toward the saturated zone/groundwater.

    • Capillary Rise: Upward movement of water from the water table into the unsaturated zone.

Soil Composition and Physical Properties

  • Soil Constituents:

    • Mineral Particles: Categorized by diameter:

      • Coarse Fragments (stones, etc.): Over 2 mm2\,mm diameter.

      • Sand: 0.063 mm0.063\,mm to 2 mm2\,mm.

      • Silt: 0.002 mm0.002\,mm to 0.063 mm0.063\,mm.

      • Clay: Under 0.002 mm0.002\,mm.

    • Organic Material: Comprised of living plants/animals and decomposing matter; usually makes up less than 5%5\% of the soil volume.

    • Water: Exists in three possible phases (solid, liquid, gas).

    • Air: Usually water-saturated; contains 0.3%0.3\% to 1%1\% CO2CO_2.

  • Soil Texture: Defined by the specific proportions of various solid particles (sand, silt, and clay).

  • Soil Heterogeneity: Soils are characterized by irregularities and heterogeneities that affect water movement.

Key Soil Moisture Parameters

  • Saturation (S=100%S=100\%): The state when all soil pores are completely filled with water.

  • Field Capacity (θfc\theta_{fc}): The amount of soil moisture held in the soil after excess water has drained away by gravity, typically occurring 2−32-3 days after saturation.

  • Wilting Point (θwp\theta_{wp}): The minimal soil moisture level at which plants can no longer extract water, leading to wilting and death; occurs at approximately 15 bars15\,bars, though this varies by species.

  • Plant Available Water (θPAW\theta_{PAW}): The difference between field capacity and the wilting point:

    • θPAW=θfc−θwp\theta_{PAW} = \theta_{fc} - \theta_{wp}

Infiltration: Definitions and Hydrological Significance

  • Definition: Infiltration is the movement of water through the soil surface into the subsurface.

  • Importance in Hydrology:

    • Determines the timing, distribution, and magnitude of surface runoff.

    • Acts as the primary step in natural groundwater recharge.

    • Base Flow: The portion of stream flow derived from subsurface flow (water that infiltrated but returned to the surface in a stream channel). This ensures streams run even during dry spells, which is critical for fish, invertebrates, and aquatic plants.

  • Core Terminology:

    • Infiltration Rate (ff): The actual rate at which water enters the soil.

    • Infiltration Capacity (fcf_c or fpf_p): The maximum rate [mm/hmm/h] at which a given soil can absorb water at a specific time.

    • Percolation: Downward movement through the unsaturated soil to reach groundwater.

The Mechanics and Analogy of Infiltration

  • The Container Analogy:

    • Imagine a container covered with wire mesh.

    • If rainfall intensity exceeds the mesh's capacity to let water through, the excess overflows (Runoff).

    • The container has a maximum rate of absorption (Infiltration Capacity) and a maximum storage volume (Field Capacity).

  • Rainfall Intensity (ii) vs. Infiltration Capacity (fcf_c):

    • If i<fci < f_c: The actual infiltration rate f=if = i.

    • If i≥fci \ge f_c: The actual infiltration rate f=fcf = f_c.

    • Ponding Infiltration: Occurs when water is applied under positive pressure (ponding), which can cause the infiltration rate to momentarily exceed the capacity.

    • Moisture Effect: Infiltration rate decreases as soil moisture increases.

Factors Influencing Infiltration Capacity

  • Characteristics of Soil:

    • Texture/Structure: Loose, permeable sandy soils have higher fcf_c than tight, clayey soils.

    • Under Drainage: Soils that can easily transmit water downward to storage maintain higher fcf_c.

    • Layering: The transmission capacity of the least permeable layer determines the overall rate.

    • Initial Moisture: Dry soils absorb more water than wet soils.

    • Land Use: Vegetated forest soils rich in organic matter have much higher fcf_c than compacted urban soils.

  • Surface Conditions:

    • Raindrop Impact: Impact causes "fines" to be displaced, which can clog upper-layer pores.

    • Vegetation Cover: Grass and vegetation reduce impact displacement, preserving higher infiltration rates.

  • Fluid Characteristics:

    • Turbidity: High clay or colloid content in water can block fine pores.

    • Dissolved Salts: Contaminants can change soil structure, impacting infiltration.

    • Temperature: Affects water viscosity; higher temperatures (lower viscosity) can increase infiltration rates.

  • Additional Factors:

    • Biological activity (root channels, animal burrows).

    • Hydrophobicity (organic deposition after fires).

    • Soil frost (variable effects based on moisture during freezing).

    • Swelling and drying (especially in clay-rich soils).

Experimental Measurement of Infiltration

  • Double-Ring Infiltrometer:

    • Apparatus: Two concentric rings inserted approximately 10 cm10\,cm into the ground.

    • Mechanism: Water is maintained at a fixed level (e.g., 5 cm5\,cm) in both rings. The outer ring acts as a water jacket to prevent the lateral spreading of water from the inner ring, ensuring vertical flow.

    • Procedure: As water infiltrates, the volume is replenished from a burette to maintain the pointer level. Volume added is recorded over time.

    • Duration: Tests continue until a uniform (steady) rate is reached, typically taking 2−32-3 hours.

    • Protection: A perforated disk is often used on the soil surface to prevent turbidity and soil disturbance.

  • Sprinkler Experiments:

    • Simulates natural rainfall. Total infiltration is computed by subtracting measured surface runoff (qoutq_{out}) from the supply rate (qinq_{in}):

    • fp=qin−qoutf_p = q_{in} - q_{out}

Mathematical Estimation of Infiltration: Horton’s Equation

  • Concept: Horton's equation describes the exponential decay of infiltration capacity from an initial high rate to a constant steady-state rate as the soil saturates.

  • Horton Equation:

    • f=fc+(f0−fc)e−Ktf = f_c + (f_0 - f_c)e^{-Kt}

    • Where:

      • ff = infiltration rate at any time tt

      • f0f_0 = initial infiltration rate at the start (t=0t=0)

      • fcf_c = constant steady-state infiltration rate reached after saturation

      • KK = Horton’s decay constant (dimension of T−1T^{-1})

      • tt = time from the beginning of rainfall

  • Linearization for Parameter Determination:

    • Through logarithmic transformation, the equation is converted to a straight-line form:

    • log⁡10(f−fc)=log⁡10(f0−fc)−Ktlog⁡10(e)\log_{10}(f - f_c) = \log_{10}(f_0 - f_c) - K t \log_{10}(e)

    • Plotting log⁡10(f−fc)\log_{10}(f - f_c) vs. tt yields a straight line with a slope −Klog⁡10(e)-K \log_{10}(e). This allows for the calculation of the constant KK.

Introduction to Evaporation and Transpiration

  • Evaporation: Conversion of liquid water to vapor from surfaces like rivers, lakes, soil moisture, and wet vegetation.

  • Transpiration: Movement of water through plants and its release into the air through leaf stomata.

  • Evapotranspiration (ET): The combined loss from land/water surfaces and vegetation.

  • Hydrological Importance:

    • Water Balance: Essential for calculating runoff and recharge.

    • Irrigation: Determines crop water requirements.

    • Reservoir Management: Essential for storage planning to account for evaporation losses.

    • Urban Hydrology: Influences green infrastructure and cooling designs.

  • Influencing Factors:

    • Temperature: Positive correlation.

    • Humidity: Negative correlation (high humidity reduces the vapor pressure gradient).

    • Wind Speed: Increases evaporation by removing saturated air near the surface.

    • Solar Radiation: Provides the energy (latent heat) required for phase change.

    • Vegetation/Soil Moisture: Available water and plant density limit the maximum ET.

Measurement and Estimation Methods for Evapotranspiration

  • Evaporation Measurement:

    • Class A Evaporation Pan: Uses water loss from a standard pan.

    • E=Kp×EpE = K_p \times E_p

    • Where EE is actual evaporation, KpK_p is the pan coefficient, and EpE_p is measured pan evaporation.

    • Energy Balance Method:

    • E=Rn−G−HλE = \frac{R_n - G - H}{\lambda}

    • Where RnR_n = net radiation, GG = soil heat flux, HH = sensible heat, and λ\lambda = latent heat of vaporization.

  • Transpiration estimation:

    • Lysimeters: Measuring water use by weighing a soil-plant system.

    • FAO Penman-Monteith Equation (Standard):

    • ET0=0.408Δ(Rn−G)+γ900T+273u2(es−ea)Δ+γ(1+0.34u2)ET_0 = \frac{0.408\Delta(R_n - G) + \gamma \frac{900}{T + 273} u_2(e_s - e_a)}{\Delta + \gamma(1 + 0.34u_2)}

    • Where:

      • ET0ET_0 = Reference evapotranspiration (mm/daymm/day)

      • Δ\Delta = Slope of vapor pressure curve

      • γ\gamma = Psychrometric constant

      • TT = Air temperature (∘C^{\circ}C)

      • u2u_2 = Wind speed at 2 m2\,m height (m/sm/s)

      • es−eae_s - e_a = Vapor pressure deficit (kPakPa)

Applications and Challenges in Civil and Environmental Engineering

  • Applications:

    • Dams/Reservoir design (water budgeting).

    • Watershed management and runoff generation models.

    • Urban green spaces (cooling effects and stormwater reduction).

    • Climate change predictive modeling.

  • Challenges:

    • High spatial and temporal variability.

    • Data limitations in developing regions.

    • Complexity in modeling biological/soil-plant-atmosphere interactions.

Comprehensive Worked Examples

  • Example 1: Horton’s Equation Curve Fitting:

    • Data: t=0,f=10.4t=0, f=10.4; t=0.5,f=3.2t=0.5, f=3.2; constant rate fc=1.0 cm/hf_c = 1.0\,cm/h.

    • Using the linearized form: log⁡10(f−fc)\log_{10}(f - f_c) vs tt.

    • For t=0t=0, f−fc=9.40f - f_c = 9.40, log⁡10=0.973\log_{10} = 0.973.

    • Slope of the line from data was determined to be −0.760-0.760.

    • K=10.760log⁡10(2.718)≈3.03K = \frac{1}{0.760 \log_{10}(2.718)} \approx 3.03.

    • Final equation: f=1+9.4e−3.03tf = 1 + 9.4e^{-3.03t}.

  • Example 2: Class A Pan Lake Evaporation:

    • Given: Ep=6.5 mm/dayE_p = 6.5\,mm/day, Kp=0.7K_p = 0.7.

    • Calculation: E=0.7×6.5=4.55 mm/dayE = 0.7 \times 6.5 = 4.55\,mm/day.

  • Example 3: Penman-Monteith Calculation:

    • Given: Rn=15 MJ/m2/dayR_n = 15\,MJ/m^2/day, T=25∘CT = 25^{\circ}C, u2=2.0 m/su_2 = 2.0\,m/s, es−ea=1.2 kPae_s - e_a = 1.2\,kPa, Δ=0.188\Delta = 0.188, γ=0.066\gamma = 0.066.

    • Numerator: (0.408×0.188×15)+(0.066×(900/298)×2.0×1.2)=1.150+0.479=1.629(0.408 \times 0.188 \times 15) + (0.066 \times (900/298) \times 2.0 \times 1.2) = 1.150 + 0.479 = 1.629.

    • Denominator: 0.188+0.066×(1+0.34×2.0)=0.188+0.111=0.2990.188 + 0.066 \times (1 + 0.34 \times 2.0) = 0.188 + 0.111 = 0.299.

    • ET0=1.629/0.299=5.45 mm/dayET_0 = 1.629 / 0.299 = 5.45\,mm/day.

  • Example 4: Reservoir Loss:

    • Area: 2.5 km2=2.5×106 m22.5\,km^2 = 2.5 \times 10^6\,m^2.

    • Rate: 6.2 mm/day=0.0062 m/day6.2\,mm/day = 0.0062\,m/day.

    • Time: 30 days30\,days.

    • Volume Loss: 2.5×106×0.0062×30=465,000 m32.5 \times 10^6 \times 0.0062 \times 30 = 465,000\,m^3.

  • Example 5: Irrigation Efficiency:

    • Maize Area: 10,000 m210,000\,m^2. ET0=5.2 mm/dayET_0 = 5.2\,mm/day, Kc=1.15K_c = 1.15.

    • ETc=1.15×5.2=5.98 mm/dayET_c = 1.15 \times 5.2 = 5.98\,mm/day.

    • Required Volume (considering 75%75\% efficiency): (0.00598×10,000)/0.75=79.73 m3/day(0.00598 \times 10,000) / 0.75 = 79.73\,m^3/day.