7. Module 4 Surface Mining_Aqueous Extraction Methods - Placer mining 2(1)
Classification and Fundamentals of Aqueous Extraction Methods
Aqueous extraction refers to a category of surface mining methods that employ water or liquid solvents to recover minerals either from their original position in the earth or from previously broken rock. These methods utilize two primary mechanisms: the hydraulic action of a liquid (typically water) and the chemical attack of solutions on specific minerals. Currently, these methods account for approximately of global surface mineral production. While they are used less frequently than mechanical extraction methods, their application is increasing significantly for certain minerals due to the variety of available techniques and the fact that most aqueous mining methods are comparatively inexpensive.
Aqueous extraction is divided into two primary subclasses: Placer mining and Solution mining. Placer mining involves the recovery of heavy minerals from alluvial or placer deposits, utilizing water for excavation, transportation, and concentration. This subclass includes hydraulic mining and both shallow-water and deep-sea dredging. Solution mining is utilized for recovering soluble or fusible minerals, or those that can be retrieved as a slurry. This method employs ordinary water, heated water, or chemical solvents and encompasses borehole extraction (multiple well methods), leaching procedures (such as dump, heap, and in-situ leaching), and evaporite/evaporation methods. While these methods have historically had limited application, leaching has seen a surge in use, particularly within gold and copper mining operations.
Placer Mining: Principles and Properties for Minability
A placer deposit is a concentration of minerals re-deposited in an unconsolidated form by fluid action, most commonly appearing as sand and gravel deposits formed by water. Common minerals sourced from placers include gold, diamonds, tin, titanium, platinum, tungsten, chromite, magnetite, coal, phosphates, sand, and gravel. For a placer deposit to be considered minable by aqueous methods, it must satisfy six key properties: (1) the material must be amenable to disintegration by high-pressure water or mechanical dislodgement; (2) there must be an adequate water supply at the required pressure head; (3) there must be sufficient space available for waste disposal; (4) there must be a significant difference in density between the ore and gangue to facilitate separation; (5) the natural gradient must support the hydraulic transport of minerals; and (6) the operation must be able to comply with environmental regulations.
Hydraulic Mining: Mechanisms and Operational Cycle
Hydraulic mining, also known as water-jet cutting, involves directing a high-pressure stream of water against a bank to undercut and cave it. As the bank material disintegrates, the loosened particles, including minerals, sand, and gravel, are carried in water as a slurry. This slurry is washed into a sluice—either a natural ground trough or a constructed box—and transported via gravity to a riffle box or other concentrating devices. The water is applied using a hydraulic monitor, also known as a giant nozzle. A specific design known as the "Intelligiant" uses curved pipe sections to balance reactive forces, making it easier to anchor and control. Some monitors are even mounted on mobile carriers and programmed to cycle across the bank automatically.
The technical development of hydraulic monitors parallels that of fire-suppression systems. For maximum impact energy, the monitor is ideally positioned at a distance of nozzle diameters from the face. However, safety concerns regarding ejected stones (which occur when the jet hits a reflector like a flat stone) often dictate a greater distance. Operational design specifications for monitors typically include nozzle diameters between and , operating pressures ranging from to , and volume flow rates between and . Target water jet velocities depend on the material: approximately for sand, for gravel, and for boulders.
The development sequence for hydraulic mining requires ensuring an upstream water supply, a downstream waste area, and strict water quality controls. Stripping is rarely required, but if necessary, monitors are used. The production cycle is highly abbreviated because breakage and transport are handled simultaneously by the water. Deposits amenable to this method are typically flat ( to grade), shallow, and thickness between and . Advantages include high productivity ( to per employee-shift), low relative cost (approximately ), and low capital costs. However, environmental damage is severe, water requirements are extensive, and the method is limited to unconsolidated deposits.
Placer Mining: Dredging Methods and Equipment
Dredging is the underwater excavation of placer deposits from floating vessels, which often house processing and waste disposal facilities. These operations require between and of water. Dredges are categorized as mechanical (dipper, bucket, and ladder dredges) or hydraulic (suction dredges). Key types include bucket-line dredges, cutter-head suction dredges, and cutter-wheel suction dredges. Bucket-line dredges are mechanical units that move a continuous line of buckets around a ladder to excavate material up to depths of . Waste is discarded via a stacking conveyor at the rear. These dredges are moved using spuds and wire ropes and can even "carry" their own pond by digging forward and filling in behind. Suction dredges use a cutter-head to free material before sucking it into a pipeline; these typically reach depths of .
Large bucket-line dredges are highly productive but require significant capital investment, ranging from for units with buckets to for those with buckets. The productivity of such an operation can be calculated using the following formulas:
$$\text{Low output} = (0.28\,m^3) \