Utility Arboriculture: Electrical Knowledge and Systems
Overview of Utility Arboriculture and Electrical Safety
Instantaneous Commodity Nature: Electricity is the only product that is produced, transported, delivered, and consumed in the same instant (Driggs 2005).
Engineering Significance: The complex grid system that instantaneously produces and delivers electricity was designated by the National Academy of Engineering as the most significant engineering accomplishment of the 20th century.
Public Expectations and Service Interruptions:
Inhabitants of the developed world expect a flawless power supply (Schewe 2007) and routinely consider themselves wronged during outages (Oberbeck and Smart 2004).
Despite high reliability expectations, power outages occur, and trees are responsible for a large percentage of these service interruptions (Russell 2011).
Tree-power line conflicts create serious electrical and fire safety risks.
Scope of Utility Arboriculture:
Utility arborists are responsible for minimizing tree-related electrical conflicts.
Successful job execution requires traditional arboricultural expertise, including tree biology, pruning, and tree risk assessment.
Utility arborists are uniquely distinguished from traditional arborists by their required command of utility-specific subjects, including electrical principles, utility systems, and specialized safety standards.
Fundamentals of Electricity
Physical Analogy:
Because electricity is invisible, it is effectively conceptualized using a fluid or hydraulic model.
Just as water flows downhill, electricity consistently seeks the path of least resistance to ground.
Electricity travels to ground through conductive objects, often utilizing more than one route simultaneously.
When electricity enters the ground, it dissipates outward in concentric "ripples," similar to the waves created when a rock falls into calm water (Miller 2002).
Electrical charges ultimately return to their original source (Wellman 1959).
Voltage ():
Definition: A volt is a measure of electrical force or electromotive force (EMF), representing the electrical pressure in a system.
Hydraulic Analogy: Volts are directly analogous to pounds per square inch () or kilopascals () in a hydraulic system.
Notation: Electrical engineers symbolize voltage using the capital letter .
Units: Voltage is commonly expressed in thousands using the international prefix "kilo" (), where .
Voltage Ranges:
North American utilities operate at voltages ranging from for end users up to for the largest transmission lines (Wellman 1959).
In Europe and other regions, voltage ranges from to , operating mostly as alternating current (AC).
Electrical Potential vs. Work:
Voltage alone performs no work; it represents stored potential for work, termed electrical potential.
A high-voltage line can be fully energized to thousands of volts without any electricity running through it.
This is analogous to a high-pressure water hose pressurized to () with its valve closed: pressure exists, but no water flows.
When an electrical appliance is turned on, the electrical "valve" opens, current begins to flow, and potential is realized by starting to work.
Current and Amperage ( or ):
Definition: An amp or ampere is the measure of current, defining the amount or volume of electricity flowing.
Notation: Abbreviated with a capital . Engineers also utilize the symbol (representing intensity).
Quantitative Standard: One amp is the charge carried by electrons moving past a given point in (Wellman 1959).
Hydraulic Analogy: Amps are analogous to gallons per minute or liters per minute in the hydraulic model.
Circuit Variability: Amperage is variable on a particular circuit depending on demand; as electrical demand increases, amperage increases.
Power and Wattage ( or ):
Definition: A watt is a measure of electric power.
Basic Mathematical Relation: One watt is produced when one amp flows at one volt ().
Notation: Symbolized by or (standing for power).
Mechanical Horsepower Equivalent: (watts are named for James Watt, credited with inventing an improved steam engine).
Practical Measurement:
Electrical fixtures are commonly labeled with the wattage they draw (e.g., light bulbs).
Consumer power utilization is measured in kilowatt-hours () using the formula:
A megawatt () is one million watts (). Power generation plants often produce many hundreds of megawatts of power (Whitaker 1999).
Resistance ( or ):
Definition: Resistance is the inherent opposition to current flow in all electrical systems.
Energy Dissipation: Dissipates electricity proportionally to the square of the current () (Schewe 2007).
Units and History: Measured in ohms, designated by the letter or the Greek symbol . Named for Georg Sikmon Ohm, who in 1820 related resistance to volts () and amps () in Ohm's law (Wellman 1959).
Ohm's Law Equation:
Definition of One Ohm: By definition, one ohm is one volt flowing at one amp (or any number of volts at the same number of amps).
Proportional Rearrangement:
At constant resistance, increasing voltage increases amperage.
Ohm's Law Circle Relationships:
Power Formulas ( or ):
Current Formulas ():
Voltage Formulas ():
Resistance Formulas ():
Impedance:
Misconception: Impedance is often incorrectly used as a synonym for resistance on AC systems.
Constituent Components: Resistance constitutes roughly of impedance. The remaining comprises inductive reactance and capacitive reactance:
Inductive Reactance: Caused by a small amount of load lost whenever current flows into a coil (such as those in transformers).
Capacitive Reactance: A charge that builds up between long parallel conductors, which slightly hinders current.
Definition: Total impedance equals the sum in ohms of resistance, inductive reactance, and capacitive reactance (Van Soelen 2006).
Conductivity:
Definition: The capacity of a material to transmit electricity; defined as the reciprocal of resistance.
High Conductivity Materials (Low Resistance): Readily transmit electricity. Aluminum and copper are good conductors, making them standard for electrical wire.
Poor Conductors / Insulators (High Resistance): Offer high opposition to electricity, requiring greater voltage to accommodate flow. Standard insulating materials include fiberglass, glass, polymers, and porcelain.
Circuits:
Definition: Electrical current completes a continuous circle or circuit to and from its source.
Required Return Path: A complete circuit needs a return path, which may be a neutral wire, a ground connection, or another energized wire.
Circuit Interruption: A break in the circuit completely stops the flow of current (Van Soelen 2006).
Terminology: In North America, utilities also refer to distribution circuits as feeders.
Circuit Disturbances, Faults, and Electromagnetic Principles
Power Outages: Defined as sustained service interruptions (Russell 2011).
Overcurrents:
Amperages in a conductor larger than those for which it is rated.
Caused by lightning, faults, or improper design.
Faults and Short Circuits:
Fault Definition: A bypass of an intended conducting path, generating abnormal fault current; also called a short circuit (Whitaker 1999).
Fault Paths: Short circuits occur between a phase (energized conductor) and another phase, a phase and the system neutral, or a phase and the ground (Van Soelen 2006).
Direct vs. Indirect Faults:
Direct Faults: Occur when two phase wires contact one another directly.
Indirect Faults: Caused when external conductive objects, such as tree branches, bridge two phase wires (Russell 2011).
Transient Faults: Affect the dielectrical properties of a system for an instant and no longer exist after power is restored.
Intermittent Faults: Repeated momentary interruptions in the same place due to the same cause (Institute of Electrical Engineers 1983), often resulting from sporadic equipment malfunction.
Current Surges:
Sudden inrushes of electricity.
Caused when electrical devices (such as motors or transformers) are first turned on, drawing several times their normal operating load.
Frequently occur when circuits are re-energized following an outage.
Inductance and Electromagnetism:
Definition: Electrification of a wire by passing it through a moving electromagnetic field.
Faraday's Law: In 1831, James Faraday developed the law of electromagnetic induction when he established voltage in a coiled wire.
Theoretical Basis: Faraday theorized that lines of force flow out of the north pole into the south pole of a magnet, creating electromagnetic fields. Lines flowing in the same direction relative to magnetic poles repel one another in the same way as similar magnetic poles (Wellman 1959).
Electric Grid Architecture: Generation to End User
System Layout and Flow: Electricity originates at generation plants transmission subtransmission distribution secondary voltage service drop lines end users (residential and commercial customers). Industrial customers are sometimes served directly by subtransmission lines.
Phase Configurations ():
An energized conductor or wire in a circuit is called a phase ().
Three phases are produced in field windings inside generating facilities, each carried on a single wire.
On transmission or distribution circuits, the three phases are designated as A, B, C; X, Y, Z; or identified by utility color coding.
Common Voltage Classifications: (Source: Abbott, Dubish, and Rooney 2005)
Extra-High Transmission Voltage:
Transmission Voltage:
Subtransmission Voltage:
Distribution Voltage:
Secondary or Customer Voltage:
Power Generation Facilities:
Operating Voltage: Electricity is generated in power plants at distribution voltage, typically between and (IBEW/NECA 2006).
Routing: Electricity occasionally flows directly from generation facilities into the distribution system, but far more commonly it is stepped up to transmission voltage for long-distance transmission.
Facility Siting: Power plants are large industrial facilities typically situated in remote rural areas far from population centers. Siting near raw fuel sources (coal, oil, natural gas) minimizes costs, as transporting raw fuel is significantly more expensive than transmitting electricity.
System Control Centers and SCADA:
Centralized control centers coordinate utility systems to manage the logistical challenge of handling electricity as an instantaneous commodity.
Computerized control center equipment continuously analyzes and balances generation output with demand (IBEW/NECA 2006).
Control centers utilize supervisory control and data acquisition (SCADA) systems to automatically collect data and perform remote switching operations (Van Soelen 2006).
Transmission Systems:
Origin and Extent: Transmission lines originate at power plant substations. First-stage lines leaving power plants are stepped up to extra-high voltage () and extend for hundreds of miles or kilometers to transmission substations.
AC vs. DC: Most transmission lines operate on alternating current (AC). However, some of the highest voltage lines use direct current (DC), which can be less expensive and exhibits lower electrical loss over long distances.
Grid Interconnection and Interconnects:
Main transmission lines are interconnected within and between utilities, optimizing generation capacity and avoiding the need for expensive peaking power plants that run only during local peak usage.
The United States and southern Canada are divided into three major regional interconnects: Eastern, Western, and Texas (Driggs 2005).
Lines within each interconnect are designated by planning coordinators as elements of the Interconnection Reliability Operating Limit (IROL) or, in the Western Interconnect, as part of the major transfer path under the Western Electric Coordinating Council (North American Electric Reliability Corporation 2008).
Example Efficiency: In the Western Interconnect, peak electrical demand occurs during winter in the Pacific Northwest and during summer in the Rocky Mountain region. The interconnected grid enables Rocky Mountain fossil fuel plants to supply peak winter loads in the Northwest, while Pacific Northwest hydroelectric facilities supplement Rocky Mountain generation during summer peaks.
Transmission Substations and Switchyards:
Substations: Terminate transmission lines and alter voltages, using transformers to step up or step down voltage in lines.
Switchyards: Route power through various circuits as needed and compensate for localized power failures. Switchyards protect circuits via disconnect switches, circuit breakers, relays, and communication systems (Van Soelen 2006).
Subtransmission Systems:
Voltage Ratings: Energized between and , though some utility subtransmission lines operate as high as or more.
Operational Difference: Unlike transmission lines, subtransmission lines are not interconnected.
Function and Placement: Link subtransmission and distribution substations to one another, feeding distribution systems and supplying industrial customers directly. Subtransmission lines are frequently constructed physically over distribution circuits on shared structures.
Generally, substations are served by multiple lines so they can depend on more than one source of energy supply.
