Irrigation Exam Study Notes

Definitions

  • Absorption rate:
    • Also known as precipitation rate, application rate, or infiltration rate.
  • SVB:
    • Stands for spill-resistant vacuum breaker.
  • Control Wires:
    • The larger the gauge number, the smaller the wire.
  • Term for Uniform Coverage:
    • Matched precipitation: All heads discharge varying amounts of water, combining to produce uniform coverage.
  • Pressure Calculation:
    • StaticPressure−AllPressureLosses=DesignPressureStatic Pressure - All Pressure Losses = Design Pressure
  • AWWA:
    • Stands for American Water Works Association.
  • Valve Type:
    • Check Valve: A valve permitting water to flow in one direction.
  • Controller Operation:
    • Cycle: One complete operation of a controller through all programmed stations.
  • Pressure Requirement:
    • Design pressure: Minimum pressure required for a system to operate properly.

Potential Damage

  • Damage from unrestricted water flow:
    • Dry line shock: Type of damage occurring when water travels unrestricted through empty lateral lines.
    • It can also result in surge and water hammer.

Irrigation System Elements

  • Drip Irrigation:
    • Emitter: Device that allows water to flow out slowly in a drip irrigation system.
  • Emitter Discharge Rate:
    • An emitter's discharge rate is best described as 2 GPH.
  • Residential Spray Head Discharge Rate:
    • A residential spray head's discharge rate is best described as 2 GPM.

Pressure and Flow

  • Pressure Loss:
    • When water flows through piping, pressure is lost as a result of friction.
  • Design Pressure Guideline:
    • As a general guideline, the design pressure should not exceed 75% of the static pressure.
  • Sleeve Size:
    • Generally, sleeves should be at least 2 sizes larger than the irrigation piping required.
  • Pipe Type:
    • Schedule pipe: PVC pipe with the same physical dimensions as iron pipe.

Plant Water Dynamics

  • Water Vapor Emission:
    • Transpiration: The process of plant material giving off water vapor from the leaves.
  • Shock Wave:
    • Water hammer: A shock wave created by a fast closing valve due to high velocities.

Pipe Standards

  • Pressure Rated Plastic Pipe Designation:
    • For PVC pipe, Type one, Grade two, 2000 psi hydrostatic design pressure, the standard designation code would be 1220.
  • PVC Pipe Connection:
    • Solvent welding: Act of chemically fusing PVC pipe and fittings together.
  • PVC Abbreviation:
    • PVC stands for Polyvinyl Chloride.
  • Automatic Valve Part:
    • Diaphragm: Flexible part of an automatic valve which regulates the passage of water.
  • I.P.S.:
    • Stands for iron pipe size.
  • M.I.P.:
    • Stands for male iron pipe.

Rules, Regulations, and Standards

  • Irrigator License Renewal:
    • A licensed irrigator needs to renew his or her license once every three years according to the Rules and Regulations.
  • TCEQ Strategic Goals:
    • The strategic goals of the TCEQ are Enforcement, Water Quality, and Waste Management.
  • Permits and Inspections:
    • Both the Licensed Irrigator and the Licensed Technician (under the supervision of the irrigator) are responsible for obtaining permits and inspections.
  • Who Can Install:
    • Both a Licensed Irrigator and a Licensed Technician (under the supervision of the irrigator) can install an irrigation system.
  • Altering Irrigation Design:
    • It is acceptable for a Licensed Technician to alter the irrigation design when the design is in violation of state and local codes or when the technician receives approval from the licensed irrigator.
  • "Commission" Definition:
    • The term "Commission" refers to the Texas Commission on Environmental Quality.
  • Texas Irrigator's Advisory Council:
    • The Texas Irrigator's Advisory Council is made up of 12 members.
  • Council Appointments:
    • Members of the Texas Irrigator's Advisory Council are appointed by The Governor.
  • Public Representatives:
    • 4 members of the Texas Irrigator's Advisory Council must be representatives of the public.
  • Pipe Coverage Depth:
    • The minimum depth of pipe coverage is 6 inches.
  • Irrigation System Function:
    • Functions of an irrigation system include erosion control, dust reduction, and irrigating any type of landscape vegetation in any location.
  • License Re-Examination:
    • After a license has expired, the only way to obtain another one is to go through the re-examination process again.
  • License Expiration Notice:
    • The irrigator will lose the license if they fail to renew even if the TCEQ does not send a written notice.
  • Licensing Requirement:
    • You must be licensed or work under the supervision of a licensed individual in order to install or repair irrigation systems for a living. (true)
  • Irrigator License Renewal Requirements:
    • In order to renew an Irrigator License you must pay a renewal fee and complete at least 16 hours of agency approved continuing education credits. (true)
  • Consequences of Incomplete Continuing Education:
    • If continuing education credits are not completed before the renewal date, the irrigator will lose the license.