mech 03
1. What velocity is normally referred to as the derivative of position vector with respect to time? [span_0](start_span)[span_0](end_span)
Answer: B. instantaneous velocity [span_1](start_span)[span_1](end_span)
Rationale: Instantaneous velocity is the exact rate of change of position at a specific moment, defined mathematically as v = ds/dt.
Incorrect Choices: Average velocity (A) is calculated over a measurable time interval, not an instant. Decreasing (C) and increasing (D) velocity refer to states of acceleration or deceleration, not the fundamental definition of velocity.
2. What is the mass moment of inertia of a sphere of mass m and radius r? [span_2](start_span)[span_2](end_span)
Answer: D. 2/5 mr² [span_3](start_span)[span_3](end_span)
Rationale: Through calculus integration, the mass moment of inertia for a solid sphere rotating about its central axis is mathematically proven to be I = \frac{2}{5}mr^2.
Incorrect Choices: Option A (\frac{1}{2}mr^2) is for a solid cylinder or disk. Options B (\frac{1}{3}mr^2) and C (\frac{3}{4}mr^2) do not correspond to the geometric mass distribution of a standard solid sphere.
3. What refers to the force by which work done on a particle as it moves around any closed path is zero? [span_4](start_span)[span_4](end_span)
Answer: C. Conservative force [span_5](start_span)[span_5](end_span)
Rationale: A conservative force (like gravity or spring forces) conserves mechanical energy; moving an object in a closed loop returns it to its starting potential, meaning net work is zero.
Incorrect Choices: Non-conservative forces (D), like friction, dissipate energy as heat, so work done on a closed path is not zero. Natural (A) and Virtual (B) are not standard classifications for forces based on work paths.
4. The moment of inertia of the circle with respect to its tangent is _______ times its centroidal moment of inertia. [span_6](start_span)[span_6](end_span)
Answer: D. 5 [span_7](start_span)[span_7](end_span)
Rationale: The centroidal area moment of inertia of a circle is I_c = \frac{\pi r^4}{4}. Using the parallel axis theorem (I = I_c + Ad^2), the moment of inertia about the tangent (where d = r) is \frac{\pi r^4}{4} + (\pi r^2)(r^2) = \frac{5\pi r^4}{4}. The ratio is 5.
Incorrect Choices: Values 2 (A), 4 (B), and 3 (C) do not mathematically align with the application of the parallel axis theorem for a circular area.
5. In dynamics, linear acceleration is ________ [span_8](start_span)[span_8](end_span)
Answer: D. Motion in which acceleration increases or decreases linearly with time. [span_9](start_span)[span_9](end_span)
Rationale: While linear acceleration standardly means the rate of change of linear velocity, in the context of this specific exam's choices, option D describes uniformly changing acceleration (jerk), which is a specific type of advanced linear dynamic motion.
Incorrect Choices: Option A describes displacement, not acceleration. Option B describes general linear kinematics. Option C (uniform velocity) explicitly means acceleration is zero.
6. The moment of the resultant of two concurrent forces with respect to a center of their planes is equal to the algebraic sum of the moments of the components with respect to the same center. [span_10](start_span)[span_10](end_span)
Answer: C. Varignon's theorem [span_11](start_span)[span_11](end_span)
Rationale: Varignon's theorem (the Principle of Moments) states that the moment of a resultant force about a point is exactly equal to the sum of the moments of its individual component forces about that same point.
Incorrect Choices: The Law of reaction (A) is Newton's third law. Mass moment of inertia (B) relates to rotational resistance. The Law of inertia (D) is Newton's first law.
7. The mass moment if inertia of a cylinder about its central axis perpendicular to a circular cross section is ________ [span_12](start_span)[span_12](end_span)
Answer: B. directly proportional to its length [span_13](start_span)[span_13](end_span)
Rationale: The mass of a cylinder is m = \rho \pi r^2 L. Substituting this into the inertia formula I = \frac{1}{2}mr^2 gives I = \frac{1}{2}(\rho \pi r^2 L)r^2. Assuming constant density and radius, I is directly proportional to its length L.
Incorrect Choices: It is not independent of radius (C) or length (D), and it is proportional to the fourth power of the radius (not directly proportional to it, making A incorrect).
8. To maximize the horizontal range of the projectile, which of the following applies? [span_14](start_span)[span_14](end_span)
Answer: D. The tangent function of the angle and velocity of trajectory must be equal to 1 [span_15](start_span)[span_15](end_span)
Rationale: Maximum horizontal range on a flat surface is achieved at an launch angle of 45^\circ. The tangent of 45^\circ is exactly 1 (\tan(45^\circ) = 1).
Incorrect Choices: Maximizing velocity (A) or angle of elevation (B/C) alone without finding the optimal 45^\circ balance will not yield the maximum possible range for a given initial speed.
9. The moment of inertia of a plane figure, ________ [span_16](start_span)[span_16](end_span)
Answer: A. increases as distance of the axis moves farther from the centroid [span_17](start_span)[span_17](end_span)
Rationale: According to the parallel axis theorem (I = I_c + Ad^2), the moment of inertia increases by the product of the area and the square of the distance (d^2) as you move the axis away from the centroid.
Incorrect Choices: It is at its absolute minimum at the centroidal axis (making B zero and D false), and it is never zero for a physical shape with area (C).
10. Centrifugal force is _______ [span_18](start_span)[span_18](end_span)
Answer: B. directly proportional to the square of the tangential velocity [span_19](start_span)[span_19](end_span)
Rationale: The formula for centrifugal force is F_c = \frac{mv^2}{r}. Because v is squared in the numerator, the force is directly proportional to the square of the tangential velocity.
Incorrect Choices: It is inversely proportional to the radius (not directly proportional, A), and it is directly proportional to the object's mass (weight), not the square of it (C, D).
11. Moment of inertia of any plane figure is expressed in units of length of the ________ [span_20](start_span)[span_20](end_span)
Answer: D. fourth power [span_21](start_span)[span_21](end_span)
Rationale: Area moment of inertia is calculated by integrating area (m^2) multiplied by the square of a distance (m^2), yielding a final dimensional unit of length to the fourth power (e.g., m^4, cm^4).
Incorrect Choices: First (A), third (B), and second (C) powers do not align with the mathematical integration of area times distance squared.
12. A couple consists of two forces, _______ in magnitude, parallel and oppositely directed. [span_22](start_span)[span_22](end_span)
Answer: C. equal [span_23](start_span)[span_23](end_span)
Rationale: By definition in statics, a couple is a system of exactly two forces that are equal in magnitude, opposite in direction, and parallel, which produces pure rotation without translation.
Incorrect Choices: If the forces are unequal (B), directly proportional (A), or inversely proportional (D) but not exactly equal, they will result in a net linear force, failing to create a pure couple.
13. If the sum of the forces on a particle is not equal to zero, the particle is________ [span_24](start_span)[span_24](end_span)
Answer: C. accelerating in the same direction as the resultant force [span_25](start_span)[span_25](end_span)
Rationale: Newton's Second Law (F = ma) dictates that a net (resultant) force produces an acceleration that is directly proportional to the force and strictly in the same direction as that net force.
Incorrect Choices: Constant velocity (A) implies a net force of zero. Accelerating opposite to the resultant force (B) or moving with constant velocity oppositely (D) violates the fundamental vector direction of Newton's Second Law.
14. D' Alembert's principle is used for ________ [span_26](start_span)[span_26](end_span)
Answer: A. Reducing the problem of kinetics to equivalent statics problem [span_27](start_span)[span_27](end_span)
Rationale: D'Alembert's principle introduces a fictitious "inertial force" (-ma) to Newton's Second Law, transforming a dynamic accelerating system into an equivalent static equilibrium system (\sum F - ma = 0).
Incorrect Choices: It is a fundamental mechanics principle, not an applied structural concept strictly limited to trusses (B), floating bodies (C), or general safe structures (D).
15. If an object exerts a normal force on a surface, then its normal force is _______ [span_28](start_span)[span_28](end_span)
Answer: D. perpendicular to the surface [span_29](start_span)[span_29](end_span)
Rationale: By definition, a "normal" vector in geometry and physics is one that is strictly perpendicular (at a 90^\circ angle) to the contact surface.
Incorrect Choices: The normal force is only equal to weight (A) on a perfectly flat, horizontal surface with no other vertical forces. It is not less than frictional force (B) by default, nor is it parallel to the surface (C).
16. In dynamics, uniform motion means_________ [span_30](start_span)[span_30](end_span)
Answer: C. Uniform velocity. [span_31](start_span)[span_31](end_span)
Rationale: "Uniform motion" explicitly means moving at a constant, unchanging speed in a straight line, which defines a uniform (constant) velocity.
Incorrect Choices: Accumulated path length (A) describes distance. Straight line movement (B) doesn't guarantee the speed is constant. Linearly increasing acceleration (D) describes non-uniform, changing motion.
17. In a trajectory, at what angle will the object be fired in order to reach maximum range? [span_32](start_span)[span_32](end_span)
Answer: C. 45 deg [span_33](start_span)[span_33](end_span)
Rationale: The horizontal range formula includes the term \sin(2\theta). The sine function reaches its maximum value of 1 when the angle is 90^\circ, which means 2\theta = 90^\circ, making the optimal launch angle \theta = 45^\circ.
Incorrect Choices: Angles of 30 (A), 60 (B), and 75 (D) degrees result in sine values less than 1, meaning the projectile will hit the ground shorter than its maximum potential range.
18. Which statement about area moments of inertia is FALSE ? [span_34](start_span)[span_34](end_span)
Answer: D. The areas closet to the axis of interest contribute the most to the moment of inertia. [span_35](start_span)[span_35](end_span)
Rationale: The formula I = \int r^2 dA relies on the square of the distance (r). Therefore, areas farthest from the axis contribute exponentially more to the moment of inertia, making option D factually incorrect.
Incorrect Choices: Options A (the integral formula), B (relation to varying surface force magnitude), and C (summation of smaller areas) are all true, valid statements regarding the principles of moments of inertia.
19. Each of the following is a common unit of mass except the [span_36](start_span)[span_36](end_span)
Answer: B. poundal [span_37](start_span)[span_37](end_span)
Rationale: A "poundal" is an imperial unit of force, specifically defined as the force required to accelerate a 1-pound mass at 1 foot per second squared.
Incorrect Choices: Gram (A), Kilogram (C), and Slug (D) are all standard units measuring mass in the metric and British Engineering systems.
20. The acceleration is ________ the resultant force on the object. [span_38](start_span)[span_38](end_span)
Answer: A. directly proportional to [span_39](start_span)[span_39](end_span)
Rationale: Following Newton's Second Law (a = F/m), if mass is constant, any increase in the resultant force causes a linear, directly proportional increase in acceleration.
Incorrect Choices: Inversely proportional (B) implies acceleration drops as force rises. Proportional to squares (C) or inversely to squares (D) misrepresents the linear relationship established by F = ma.
21. The resultant of a force acting on a body will be zero, if the body_________ [span_40](start_span)[span_40](end_span)
Answer: B. does not rotate [span_41](start_span)[span_41](end_span)
Rationale: In a rigid body mechanics context, if all resultant forces and moments acting on a body are absolutely zero, the body remains in static equilibrium, meaning it neither accelerates linearly nor rotates.
Incorrect Choices: If the body rotates (A) due to a force, accelerates (C), or decelerates (D), it proves a net unbalanced force or moment is acting upon the system.
22. A measure of the resistance of a body it offers to any change in its angular velocity, determined by the mass and distribution of its mass about the axis of rotation is known as _______ [span_42](start_span)[span_42](end_span)
Answer: A. moment of inertia [span_43](start_span)[span_43](end_span)
Rationale: Moment of inertia is the exact rotational equivalent of mass; it dictates how difficult it is to alter a body's current state of rotational motion based on how its mass is spread out from the axis.
Incorrect Choices: Friction (B) resists sliding. Torsion (C) is twisting stress. Angular acceleration (D) is the result of applied torque, not the resistance to it.
23. The ratio of limiting friction and normal reaction is known as _______ [span_44](start_span)[span_44](end_span)
Answer: A. Coefficient of friction [span_45](start_span)[span_45](end_span)
Rationale: Mathematically, the coefficient of friction (\mu) is defined as the maximum static (limiting) friction force divided by the normal force pushing the surfaces together (\mu = F_f / N).
Incorrect Choices: Angle of friction (B) is the arctangent of this coefficient. Angle of response/repose (C) is a geometric slope angle. Sliding friction (D) refers to kinetic friction, not the ratio itself.
24. The acceleration is _______ the mass of the object. [span_46](start_span)[span_46](end_span)
Answer: B. inversely proportional to [span_47](start_span)[span_47](end_span)
Rationale: By rearranging Newton's Second Law (a = F/m), it is clear that for a constant applied force, as an object's mass increases, its acceleration decreases, representing an inversely proportional relationship.
Incorrect Choices: Directly proportional (A) means a heavier object accelerates faster under the same force, which is false. Squares (C, D) do not apply to the linear F=ma relationship.
25. The maximum frictional fore, which comes into play, when the body just begins to slide over the surface of the other body is known as_______ [span_48](start_span)[span_48](end_span)
Answer: C. limiting friction [span_49](start_span)[span_49](end_span)
Rationale: Limiting friction is the absolute peak value of static friction; it represents the precise threshold just before applied force overcomes static resistance and the object breaks into kinetic sliding.
Incorrect Choices: Static friction (A) covers all values up to the limit, not just the maximum. Dynamic friction (B) occurs after the sliding begins. Coefficient of friction (D) is a dimensionless ratio, not a force.
26. A stone of mass m at the end of a string of length l is whirled in vertical circle at a constant speed. The tension in the string will be maximum when the stone is _______ [span_50](start_span)[span_50](end_span)
Answer: D. At the bottom of the circle [span_51](start_span)[span_51](end_span)
Rationale: At the bottom of the swing, the string's tension must support both the downward weight of the stone (mg) and provide the required inward centripetal force (mv^2/r), making T = mg + mv^2/r.
Incorrect Choices: At the top (A), gravity assists centripetal force (T = mv^2/r - mg), making tension minimum. Half-way (B) and quarter-way (C) have tension values between the maximum and minimum extremes.
27. For a system to be in equilibrium; [span_52](start_span)[span_52](end_span)
Answer: D. I, II and III [span_53](start_span)[span_53](end_span)
Rationale: Complete static equilibrium requires that the force polygon visually closes (net force is zero), forces must be concurrent/parallel to prevent uncalculated torques, and the fundamental three static equations (\sum F_x=0, \sum F_y=0, \sum M=0) must be fully satisfied.
Incorrect Choices: Options A, B, and C omit at least one necessary condition, but all three statements (I, II, and III) are required for guaranteed equilibrium.
28. The resultant of a force acting on a body will be zero, if the body _______ [span_54](start_span)[span_54](end_span)
Answer: B. does not rotate [span_55](start_span)[span_55](end_span)
Rationale: As established in question 21, a zero resultant implies a state of equilibrium. If a body experiences no net resultant force or couple, it will not begin to translate or rotate from a resting state.
Incorrect Choices: Rotation (A) or any form of acceleration/deceleration (C, D) indicates the presence of a non-zero resultant force or moment acting on the object.
29. The moment of inertia of any plane figure can be expressed in units of length to the ________ [span_56](start_span)[span_56](end_span)
Answer: D. Fourth Power [span_57](start_span)[span_57](end_span)
Rationale: As established in question 11, calculating the area moment of inertia requires multiplying an area (length squared) by a distance squared, resulting in a unit of length to the fourth power (e.g., mm^4).
Incorrect Choices: First (A), Second (C), and Third (B) powers represent distance, area, and volume respectively, none of which represent area moments of inertia.
30. Which of the following BEST describes d'Alembert's principle? [span_58](start_span)[span_58](end_span)
Answer: A. F = ma [span_59](start_span)[span_59](end_span)
Rationale: D'Alembert's principle is a direct rearrangement of Newton's second law (F = ma) into the form F - ma = 0, conceptualizing mass times acceleration as a fictitious "inertial force" to create a pseudo-static equilibrium.
Incorrect Choices: The first law of motion (B) is inertia. Stress proportional to strain (C) is Hooke's Law. F=kx (D) is the equation for spring force.
31. A branch of physical science which deals with state of rest or motion of bodies under the action of forces. [span_60](start_span)[span_60](end_span)
Answer: A. Mechanics [span_61](start_span)[span_61](end_span)
Rationale: Mechanics is the overarching physical science that studies both how bodies remain at rest (statics) and how they move under the influence of applied forces (dynamics).
Incorrect Choices: Kinematics (B), Statics (D), and Dynamics (which is a sub-branch of mechanics) are all too narrow; Mechanics encompasses all of these specific fields.
32. How do you call the description of motion of a particle with respect to the motion of another particle in motion? [span_62](start_span)[span_62](end_span)
Answer: B. relative motion [span_63](start_span)[span_63](end_span)
Rationale: Relative motion calculates the velocity and acceleration of one body as observed from the reference frame of a second, moving body, recognizing that motion is observer-dependent.
Incorrect Choices: Linear (A) and circular (C) motion describe geometric paths. Relativistic motion (D) specifically refers to physics near the speed of light, not standard comparative kinematics.
33. Branch of mechanics which deals with bodies in motion. [span_64](start_span)[span_64](end_span)
Answer: C. Dynamics [span_65](start_span)[span_65](end_span)
Rationale: Dynamics is specifically defined as the branch of mechanics dealing with the behavior of objects that are in a state of motion under the action of forces.
Incorrect Choices: Statics (A) deals with stationary bodies in equilibrium. Kinetics (B) and Kinematics (D) are sub-branches of dynamics, but dynamics is the complete overarching category for bodies in motion.
34. Which of the following is FALSE? [span_66](start_span)[span_66](end_span)
Answer: D. The acceleration of a body rotating with a constant angular velocity is zero. [span_67](start_span)[span_67](end_span)
Rationale: Even if angular velocity is perfectly constant, a rotating body experiences normal (centripetal) acceleration continuously pulling it toward the center of the curve; therefore, its total acceleration is not zero.
Incorrect Choices: Statements A (kinematics vs kinetics), B (radius of gyration), and C (angular momentum definition) are all factually true principles of physics.
35. A pair of forces equal in magnitude, opposite in direction, and not in the same line is called [span_68](start_span)[span_68](end_span)
Answer: B. couple [span_69](start_span)[span_69](end_span)
Rationale: A couple is a specific system of two non-collinear, parallel forces that are exactly equal and opposite, generating a pure rotational moment without any linear translation.
Incorrect Choices: A moment (A) and torque (C) describe the effect of a force causing rotation, not the pair of forces itself. A tensor (D) is a mathematical array used to represent physical quantities like stress.
36. Which of the following is NOT a vector quantity? [span_70](start_span)[span_70](end_span)
Answer: B. speed [span_71](start_span)[span_71](end_span)
Rationale: Speed is a scalar quantity because it possesses only magnitude (rate of distance covered) and has no specific directional component.
Incorrect Choices: Velocity (A), acceleration (C), and displacement (D) all mathematically require both a magnitude and a specific spatial direction, classifying them as vectors.
37. A body is said to be in "rotational equilibrium" when [span_72](start_span)[span_72](end_span)
Answer: A. no net torque acts on it [span_73](start_span)[span_73](end_span)
Rationale: Rotational equilibrium dictates that a body will not experience angular acceleration; this is achieved only when the sum of all torques (moments) acting on the body is exactly zero.
Incorrect Choices: Forces can absolutely act on a body in rotational equilibrium (B), provided they intersect the center of mass or cancel out to produce zero net torque. Concurrent (D) forces do not cause rotation, but the absence of net torque is the definitional requirement.
38. What is the name for a vector that represents the sum of two vectors? [span_74](start_span)[span_74](end_span)
Answer: B. resultant [span_75](start_span)[span_75](end_span)
Rationale: In vector mathematics, the "resultant" is the single comprehensive vector obtained by adding two or more individual component vectors together, representing their combined effect.
Incorrect Choices: A scalar (A) has no direction. A tensor (C) is a complex multi-directional array. A tangent (D) is a line touching a curve, unrelated to vector addition.
39. The moment of inertia of a triangle with respect to the base is _______ time its moment of inertia with respect to its centroidal axis? [span_76](start_span)[span_76](end_span)
Answer: C. 3 [span_77](start_span)[span_77](end_span)
Rationale: The area moment of inertia of a triangle about its base is I_{base} = \frac{bh^3}{12}. Its centroidal moment of inertia is I_c = \frac{bh^3}{36}. The ratio of \frac{1}{12} to \frac{1}{36} is exactly 3.
Incorrect Choices: Values 2 (A), 4 (B), and 5 (D) do not match the geometric derivation of the parallel axis theorem for triangular shapes.
40. Which of the following represents the greatest mass? [span_78](start_span)[span_78](end_span)
Answer: D. 1 slug. [span_79](start_span)[span_79](end_span)
Rationale: Converting the units: 454g is \approx 0.45 kg; 1 lbm is \approx 0.45 kg; 1 kg is 1 kg. A slug is the British Engineering unit of mass equal to approximately 14.59 kg, making it significantly the largest.
Incorrect Choices: 454g (A), 1 kg (B), and 1 lbm (C) are all less than 1.5 kilograms, far smaller than the 14.59 kilogram mass of one slug.
41. The ratio of a load-bearing force to the applied force for a lever is called _______. [span_80](start_span)[span_80](end_span)
Answer: B. mechanical advantage [span_81](start_span)[span_81](end_span)
Rationale: Mechanical advantage is the fundamental metric used to assess a machine's performance, defined as the ratio of output force (load) to the input force (applied effort).
Incorrect Choices: Load factor (A) relates to stress limits. Efficiency (C) measures energy or work output versus input, not raw force. Influence factor (D) is a structural analysis term.
42. The theorem which is closely related to d'Alembert's theorem is the________ [span_82](start_span)[span_82](end_span)
Answer: C. Newton's second law of motion [span_83](start_span)[span_83](end_span)
Rationale: D'Alembert's principle mathematically depends on and reinterprets Newton's second law (F = ma), converting the dynamic acceleration term into an opposing pseudo-static force.
Incorrect Choices: Newton's first (A) and third (B) laws deal with inertia and action-reaction. Bernoulli's theorem (D) relates to fluid dynamics, not solid body kinetics.
43. In dynamics, rotational motion is _________ [span_84](start_span)[span_84](end_span)
Answer: A. rotation of the body about its own axis. [span_85](start_span)[span_85](end_span)
Rationale: In rigid body dynamics, "rotation" specifically describes a body spinning around an internal axis passing through the body itself, such as a wheel on an axle.
Incorrect Choices: Motion along a curved (B) or parabolic (C) path is curvilinear translation. Motion around a circular path (D) describes revolution (like a planet orbiting a sun), not internal rotation.
44. In dynamics, a linear system describes_________ [span_86](start_span)[span_86](end_span)
Answer: B. movement of particles in straight lines. [span_87](start_span)[span_87](end_span)
Rationale: A linear dynamic system deals with rectilinear kinematics, which is explicitly the mathematical description of particles moving along 1-dimensional straight-line paths.
Incorrect Choices: Accumulated length during reversals (A) describes distance. Uniform velocity (C) is a specific subset but doesn't define all linear systems. Linearly increasing acceleration (D) describes jerk, not the basic definition of a linear system.
45. How do you call the apparent force on a body directed away from the center of rotation ? [span_88](start_span)[span_88](end_span)
Answer: D. centrifugal force [span_89](start_span)[span_89](end_span)
Rationale: Centrifugal force is the apparent, outward-directed inertial force observed from a rotating reference frame, pushing mass away from the central axis of rotation.
Incorrect Choices: Normal force (A) is surface-dependent. Centripetal force (B) is the real inward force keeping the object in a curve. Coriolis force (C) acts perpendicular to velocity in a rotating frame, not radially outward.
46. Objects falling in air from the same height will not reach the ground at the same time because [span_90](start_span)[span_90](end_span)
Answer: D. I, II & III [span_91](start_span)[span_91](end_span)
Rationale: Air resistance increases as an object falls faster (I). This opposing drag eventually balances gravity, leading to a terminal velocity (II), which acts as a maximum speed cap (III). Objects with different shapes/masses reach different terminal velocities.
Incorrect Choices: Options A and B omit crucial principles, as all three statements (I, II, and III) correctly explain why aerodynamic drag alters falling times compared to a vacuum.
47. The dimensions of "Acceleration x Mass" is the same as that to_____ [span_92](start_span)[span_92](end_span)
Answer: D. Weight [span_93](start_span)[span_93](end_span)
Rationale: Based on Newton's Second Law (F = ma), mass times acceleration yields the dimension of Force. Weight (W = mg) is simply a specific gravitational force applied to a mass, sharing the exact same dimensions.
Incorrect Choices: Power (A), Work (B), and Length (C) have fundamentally different dimensional units (M L^2 / T^3, M L^2 / T^2, and L, respectively) than Force (M L / T^2).
48. One newton is the force required to _______ [span_94](start_span)[span_94](end_span)
Answer: B. acceleration at 10 kg mass at a rate of 0.10 m/s² [span_95](start_span)[span_95](end_span)
Rationale: A Newton is defined as the force needed to accelerate 1 \text{ kg} at 1 \text{ m/s}^2. Using F = ma, calculating 10 \text{ kg} \times 0.10 \text{ m/s}^2 yields exactly 1 \text{ kg} \cdot \text{m/s}^2, which equals 1 Newton.
Incorrect Choices: Option A yields 0.001 N (since 1g is 0.001 kg). Option C yields 0.01 N. Option D yields 9.81 N (which is the gravitational weight of a 1 kg mass, not 1 Newton).
49. Distance travelled in dynamics is _______ [span_96](start_span)[span_96](end_span)
Answer: B. The accumulated length of the path travelled during all direction reversals. [span_97](start_span)[span_97](end_span)
Rationale: Distance is a scalar quantity measuring the total physical ground covered by an object along its path, regardless of its starting point or how many times it changes direction.
Incorrect Choices: Option A describes displacement (a vector). Options C and D describe specific linear motion or jerks, not the fundamental definition of distance.
50. How do you call the force of the plane reaction in friction calculations? [span_98](start_span)[span_98](end_span)
Answer: C. Normal force [span_99](start_span)[span_99](end_span)
Rationale: In the friction equation F_f = \mu N, the N represents the normal force, which is the perpendicular contact reaction force exerted by a surface (plane) against a resting or sliding object.
Incorrect Choices: Tangential force (A) acts parallel to the plane (like friction itself). Centripetal (B) and centrifugal (D) forces deal exclusively with rotational/curved paths, not flat plane reactions.