Radiation Shielding and Fast Neutron Flux Calculations

Removal Cross-Section and the Fission Plate Experiment

  • The study of neutron removal is based on experimental observations utilizing a fission plate.

  • The experimental setup involves:

    • A source consisting of neutrons hitting a Uranium-235 (U−235U-235) fission plate.

    • The fission plate acting as a source of mass neutrons.

    • A shielding material, specifically water, surrounding the setup.

    • A detector placed at various distances to record flux measurements.

  • The recording focus is the removal cross-section of water and how the neutron flux varies as a function of distance.

Mathematical Analysis of the Point Water Kernel

  • The neutron flux as a function of distance is calculated based on the radius of the fission plate and the point water kernel, denoted as g(r)g(r).

  • This kernel provides insight into how neutrons coming out of the fission plate flow through water.

  • Variables identified in the calculation:

    • rr: The distance between the fission plate and the detector material, measured in cmcm.

    • ϕ(r)\phi(r): The flux, often expressed in relation to 4πr2×g(r)4\pi r^2 \times g(r).

  • The behavior of the data observed experimentally:

    • Initial behavior was non-linear.

    • After a specific distance, the behavior followed a linear trend when plotted on a log scale.

  • The flux data was fitted using the following exponential relation:     0.12×exp⁡(−0.103×r)0.12 \times \exp(-0.103 \times r)

  • The point water kernel function g(r)g(r) is defined as:     g(r)=a×exp⁡(−Σrw×r)4πr2g(r) = \frac{a \times \exp(-\Sigma_{rw} \times r)}{4\pi r^2}

    • Where a=0.12a = 0.12.

    • The microscopic removal cross-section for water (Σrw\Sigma_{rw}) is identified as 0.103 cm−10.103 \, cm^{-1}.

  • This relation is widely applied to calculate the necessary thickness or depth of water required to shield against fast neutrons.

  • The general expression for flux is given by:     ϕ=S×g(r)\phi = S \times g(r)     (where SS represents the source term).

Numerical Application: Flux from a Fission Plate Source

  • A specific problem involves calculating the fast flux at a point 75 cm75\,cm from the center of a fission plate.

  • Parameters of the problem:

    • Source: Circular fission plate with a diameter of 28 inches28\,inches.

    • Environment: A tank of water.

    • Fission Density: 4×107 fissions/cm2/s4 \times 10^7 \, \text{fissions}/cm^2/s.

  • Calculating the Fast Neutron Source Term (SS):

    • Each fission event produces approximately 2.422.42 fast neutrons (the fast neutron factor).

    • S=4×107×2.42=9.68×107 neutrons/cm2/sS = 4 \times 10^7 \times 2.42 = 9.68 \times 10^7 \, \text{neutrons}/cm^2/s.

  • Calculating Geometric Parameters:

    • Radius of the plate: 14 inches14 \, inches.

    • Conversion to centimeters: 14×2.54=35.56 cm14 \times 2.54 = 35.56 \, cm.

    • Distance (xx) to point of interest: 75 cm75 \, cm.

    • Using the relation tan⁡(θ)=rx\tan(\theta) = \frac{r}{x}:         tan⁡(θ)=35.5675=0.474\tan(\theta) = \frac{35.56}{75} = 0.474         θ=0.442 radians\theta = 0.442 \, \text{radians}

    • cos(θ)=0.9036cos(\theta) = 0.9036

    • sec⁡(θ)=1cos(θ)=1.107\sec(\theta) = \frac{1}{cos(\theta)} = 1.107

  • Calculation of Exponential Arguments:

    • Σrw×x=0.103×75=7.725\Sigma_{rw} \times x = 0.103 \times 75 = 7.725 (approximated as 7.737.73).

    • Σrw×x×sec⁡(θ)=0.103×75×1.1=8.55\Sigma_{rw} \times x \times \sec(\theta) = 0.103 \times 75 \times 1.1 = 8.55.

  • Calculating the Flux (ϕp\phi_p) using the Exponential Integral (E1E_1):     ϕp=S×a2×[E1(Σrwx)−E1(Σrwxsec⁡(θ))]\phi_p = \frac{S \times a}{2} \times [E_1(\Sigma_{rw} x) - E_1(\Sigma_{rw} x \sec(\theta))]

    • Substituting values:         ϕp=9.68×107×0.122×[E1(7.73)−E1(8.55)]\phi_p = \frac{9.68 \times 10^7 \times 0.12}{2} \times [E_1(7.73) - E_1(8.55)]

  • Approximating Exponential Integrals (E1E_1):

    • Method 1: Use a log-linear scale plot to estimate values roughly.

    • Method 2: Use the mathematical approximation E1(x)≈exp⁡(−x)x+1E_1(x) \approx \frac{\exp(-x)}{x+1}.

    • Calculated values:         E1(7.73)≈exp⁡(−7.73)7.73+1=5.1×10−5E_1(7.73) \approx \frac{\exp(-7.73)}{7.73+1} = 5.1 \times 10^{-5}         E1(8.55)≈exp⁡(−8.55)8.55+1=2.05×10−5E_1(8.55) \approx \frac{\exp(-8.55)}{8.55+1} = 2.05 \times 10^{-5}

Shielding Effects of Iron Slabs in Water

  • When other materials like steel (iron) are present, they also contribute to the reduction of neutron flux.

  • Scenario: A 3 inch3\,inch thick iron slab is placed before the water shield.

  • Removal cross-section for steel (Σrt\Sigma_{rt}) is given as 0.168 cm−10.168 \, cm^{-1}.

  • Thickness of iron (tt) in cm: 3×2.54=7.62 cm3 \times 2.54 = 7.62 \, cm.

  • The flux calculation adjusts to account for the additional material:     ϕ=S×a2×[E1(Σrwx+Σrtt)−E1(Σrwxsec⁡(θ)+Σrttsec⁡(θ))]\phi = \frac{S \times a}{2} \times [E_1(\Sigma_{rw}x + \Sigma_{rt}t) - E_1(\Sigma_{rw}x \sec(\theta) + \Sigma_{rt}t \sec(\theta))]

  • Substituting Parameters for Iron and Water Shielding:

    • Σrt×t=0.168×7.62=1.28\Sigma_{rt} \times t = 0.168 \times 7.62 = 1.28

    • Σrt×t×sec⁡(θ)=1.28×1.1=1.41\Sigma_{rt} \times t \times \sec(\theta) = 1.28 \times 1.1 = 1.41

    • Arguments for E1E_1:

      • Term 1: 7.73+1.28=9.017.73 + 1.28 = 9.01

      • Term 2: 8.55+1.41=9.968.55 + 1.41 = 9.96

  • Final Flux Calculation results in approximately 52 neutrons/cm2/s52 \, \text{neutrons}/cm^2/s.

Review of Radiation Measurement and Shielding Solutions

Problem 1: Attenuation in Aluminum and Carbon Dioxide

  • Involves radiation passing through aluminum windows and CO2CO_2 gas.

  • Absorption calculation:

    • Iout=I0×exp⁡(−μx)I_{out} = I_0 \times \exp(-\mu x)

    • Mass attenuation coefficient for Aluminum (μAl\mu_{Al}): 0.1704 cm2/g×2.7 g/cm3=0.46008 cm−10.1704 \, cm^2/g \times 2.7 \, g/cm^3 = 0.46008 \, cm^{-1}.

    • Mass attenuation coefficient for CO2CO_2 (μCO2\mu_{CO_2} ): Derived from atomic ratios (12/4412/44 for Carbon and 32/4432/44 for Oxygen).

    • μCO2 (composite)=1244(0.1514)+3244(0.1551)=0.1541 cm2/g\mu_{CO_2} \text{ (composite)} = \frac{12}{44}(0.1514) + \frac{32}{44}(0.1551) = 0.1541 \, cm^2/g.

    • Linear attenuation for CO2CO_2: 0.1541×density (1.833)=0.2825 cm−10.1541 \times \text{density (1.833)} = 0.2825 \, cm^{-1}.

  • Result: 1.08%1.08\% of radiation is absorbed, with 98.92%98.92\% transmitted.

Problem 2: Stopping Power in Water

  • Calculating stopping power due to ionization (dE/dxdE/dx).

  • Formula involves constants:

    • mc2=0.511 MeVmc^2 = 0.511 \, MeV

    • Electron density of water (nn): 3.34×1022 cm−33.34 \times 10^{22} \, cm^{-3} (converted to 1028 m−310^{28} \, m^{-3}).

    • Atomic number (ZZ) for water: 7.227.22.

    • Excitation potential (II) for water: 105.11 eV105.11 \, eV (or 110.855 eV110.855 \, eV depending on the method).

  • Total Stopping Power: 3045.41 MeV/m3045.41 \, MeV/m.

Problem 3: Alpha Stopping Power in Aluminum

  • Stopping power calculation for alpha particles in aluminum (Z=13Z=13).

  • Constants used:

    • n=6.42×1028 m−3n = 6.42 \times 10^{28} \, m^{-3}.

    • I=163×10−6 MeVI = 163 \times 10^{-6} \, MeV.

  • Result: 1.5×105 MeV/m1.5 \times 10^5 \, MeV/m.

Problem 4: Range of Alpha Particles in Gold

  • Range (RR) of 4 MeV4 \, MeV and 8 MeV8 \, MeV alpha particles.

  • Calculated range in air: 37.5 mm37.5 \, mm.

  • Refined calculation for range in gold (AuAu):

    • Using densities and atomic weights (Aeff=197A_{eff} = 197 for gold, density =19.32 g/cm3= 19.32 \, g/cm^3).

    • Result: 35.4 μm35.4 \, \mu m using one approach; 15 μm15 \, \mu m using a plot-based approach (rough estimation).

Problem 5: Energy Loss in Gold (Segmental Method)

  • Calculation for the energy loss of a 6 MeV6 \, MeV alpha particle in gold.

  • Range in silicon used for reference: 32 μm32 \, \mu m.

  • Range in gold converted: 10.23 μm10.23 \, \mu m.

  • Resulting energy loss: 1.432 MeV1.432 \, MeV.

  • If calculating via the segmental numerical method, a different result may occur, potentially earning bonus points.

Problem 6: Compton Scattering

  • Calculating the energy of scattered radiation at an angle (θ\theta) of 55∘55^{\circ}.

  • Initial energy (EE) = 50 keV50 \, keV (noted elsewhere as 0.150.15 or related values).

  • Scattered photon energy (E′E'): 0.1714 MeV0.1714 \, MeV.

  • Energy of the scattered electron: 0.21 MeV0.21 \, MeV.

Problem 7: Shielding with Lead for X-rays

  • Determining the thickness of lead needed to block 7.4 keV7.4 \, keV X-rays by a factor of 10410^4.

  • Ratio: II0=10−4\frac{I}{I_0} = 10^{-4}.

  • Mass attenuation coefficient for Lead (μ/ρ\mu/\rho): 22.8 cm2/g22.8 \, cm^2/g.

  • Density of Lead (approximate): Used as part of the calculation to find μ=137.64 cm−1\mu = 137.64 \, cm^{-1}.

  • Resulting thickness: 66 μm66 \, \mu m.

Questions & Discussion

  • Question: Could you look at the beginning of the problem again? I can’t see the top.

  • Response: The problem defines a range for a 4 MeV4\,MeV alpha particle.