DET10103 Electrical Circuits 1 - Chapter 1: Introduction to Electric Circuit

Course Overview and Learning Outcomes

Course Code: DET10103 - ELECTRICAL CIRCUITS 1 Chapter 1: Introduction to Electric Circuit

Course Learning Outcomes (CLOs)

  • CLO1: Apply the concept and principles of the related electrical circuit theorems and law to solve DC electrical circuit using various method and approach. Solve DC circuit problems using appropriate DC electrical laws and theorems (C3, PLO 1).

  • CLO2: Construct DC circuit and measure related electrical parameters using appropriate electrical equipment (P4, PLO 5).

  • CLO3: Demonstrate ability to work in team to complete assigned tasks within the stipulated time frame (A3, PLO 8).

Topic Outline and Face-to-Face (F2F) Hours

  1. Introduction to Electric Circuit: 8 Hours

  2. DC Equivalent Circuit and Network Theorems: 7 Hours

  3. Capacitors and Capacitance: 4 Hours

  4. Inductors and Inductance: 4 Hours

  5. Magnetic Circuit, Electromagnetism and Electromagnetic Induction: 4 Hours

Learning Outcomes for Section 1.1 and 1.2

Upon completion of this section (2 Hours), students should be able to:

  • Remember standard symbols for electrical components.

  • Identify common symbols in electrical circuit diagrams.

  • Apply the general features of cells and batteries.

  • Show the difference between cells and batteries.

  • Show the effects of different cell connections (series, parallel, and series-parallel).

  • Calculate the total voltage of series sources with same and opposite polarities.

Standard Symbols for Electrical Components

  • Conductor/Wire: A line representing a connection.

  • Switch: A component to open or close a circuit.

  • Ground/Earth: Represents the zero potential reference.

  • Cell (DC Supply): A single unit of energy shown with one long and one short parallel line.

  • Battery (DC Supply): A combination of multiple cells.

  • AC Supply: A circle with a sine wave symbol inside.

  • Resistor: A zigzag line or rectangle.

  • Inductor: A coiled/loopy line.

  • Capacitor: Two parallel lines of equal length.

  • Galvanometer: Represented by the symbol G.

  • Voltmeter: Represented by the symbol V.

  • Ammeter: Represented by the symbol A.

Cells and Batteries

Definitions

  • Cell: A single unit of a primary or secondary battery that converts chemical energy into electric energy.

  • Battery: A series of two or more connected cells, which changes chemical energy into electrical energy.

Relationship and Practical Application

  • A battery is a combination of cells.

  • Cell combinations can be configured in Series, Parallel, and Series-Parallel.

  • Practically, a single cell is often also referred to as a battery.

Cell Connections and Calculations

1. Series Connection

In a series connection, the negative terminal of one cell is connected to the positive terminal of the next.

  • Current: The current (1000 mA1000\,mA in example) remains the same through all cells.

  • Voltage: The voltages add up.

  • Formula for Total EMF: ET=E1+E2+E3+E4E_T = E_1 + E_2 + E_3 + E_4

  • Example 1.1: If four cells of 2.0 V2.0\,V each are in series, ET=2.0+2.0+2.0+2.0=8 VE_T = 2.0 + 2.0 + 2.0 + 2.0 = 8\,V.

2. Parallel Connection

In a parallel connection, all positive terminals are connected together, and all negative terminals are connected together.

  • Current: The capacities/currents add up. If four cells of 1000 mA1000\,mA are in parallel, the total current is 4000 mA4000\,mA.

  • Voltage: The total voltage remains the same as a single cell.

  • Formula for Total EMF: ET=E1=E2=E3E_T = E_1 = E_2 = E_3

  • Example 1.2: If three cells of 2.0 V2.0\,V are in parallel, ET=2.0 VE_T = 2.0\,V.

3. Series-Parallel Connection

This combines both types of connections.

  • Example 1.3: Four cells of 2.0 V2.0\,V each are connected in two strings of series connections, and those strings are then paralleled.

  • Series Calculation: ESeries=E1+E2+E3+E4=8 VE_{Series} = E_1 + E_2 + E_3 + E_4 = 8\,V.

  • Total Voltage: ET=ESeries=8 VE_T = E_{Series} = 8\,V.

Series Potentials and Polarities

  • Same Polarities: If sources are connected in the same direction, the voltages add.

    • Formula: ET=E1+E2E_T = E_1 + E_2

    • Example 1.4: ET=8+6=14 VE_T = 8 + 6 = 14\,V.

  • Opposite Polarities: If sources are connected in opposing directions, the smaller voltage is subtracted from the larger.

    • Formula: ET=E1−E2E_T = E_1 - E_2

    • Example 1.5: ET=8−6=2 VE_T = 8 - 6 = 2\,V.

Electric Current and Quantity of Electricity

Upon completion of this section (1 Hour), students should be able to:

  • State the definition of electric current.

  • State the unit of charge.

  • Calculate charge (QQ) from Q=ItQ = It.

  • Identify the three main effects of electric current with examples.

  • Explain the four factors affecting resistance.

  • Calculate resistance using R=ρlAR = \frac{\rho l}{A}.

Definition of Current and Charge

  • Current (II): The motion of charge. It depends on the rate of flow of charge, sometimes described as "electric fluid."

  • Unit of Current: Ampere (AA).

  • Standard Formula: I=dqdtI = \frac{dq}{dt}

  • Steady State Formula: I=QtI = \frac{Q}{t}, which leads to Q=ItQ = It.

  • Charge (QQ): Measured in Coulombs (CC).

  • Time (tt): Measured in Seconds (ss).

Example 1.6: If a current of 5 A5\,A flows for 22 minutes:

  • t=2×60=120 st = 2 \times 60 = 120\,s

  • Q=5×120=600 CQ = 5 \times 120 = 600\,C

Main Effects of Electric Current

  1. Heat Effect: Examples include soldering irons, water heaters, fuses, bulbs, cookers, electric fires, furnaces, kettles, and irons.

  2. Magnetic Effect: Examples include bells, relays, motors, generators, transformers, telephones, lifting magnets, and car ignitions.

  3. Chemical Effect: Examples include cells, batteries, and electroplating.

Resistance and Resistivity

Resistance (RR)

Resistance is the property of a component which restricts the flow of electric current. The basic unit is the Ohm (Ω\Omega).

Factors Determining Resistance

There are four factors that dictate the value of resistance:

  1. Length (ll)

  2. Cross-sectional area (AA)

  3. Resistivity (ρ\rho)

  4. Temperature

The Resistance Formula

R=ρlAR = \frac{\rho l}{A}

  • RR = Resistance (Ω\Omega)

  • ll = Length (mm)

  • AA = Cross-sectional area (m2m^2)

  • ρ\rho = Resistivity (Ω.m\Omega.m)

Example 1.7: Calculate the resistance of a 5 m5\,m long conductor with a cross-sectional area of 10 mm210\,mm^2 (10×10−6 m210 \times 10^{-6}\,m^2) and resistivity of 0.3×10−5 Ω.m0.3 \times 10^{-5}\,\Omega.m.

  • R=0.3×10−5×510×10−6=1.5 ΩR = \frac{0.3 \times 10^{-5} \times 5}{10 \times 10^{-6}} = 1.5\,\Omega

Resistor Device

A manufactured device with a specific resistance used to limit current and reduce voltage. Examples include power resistors like 1800 Ω1800\,\Omega, 5%5\%, 4 W4\,W or 40 Ω40\,\Omega, 10%10\%.

Ohm's Law and Simple Circuits

Learning outcomes for this section (1 Hour) include explaining Ohm's law, outlining procedures for its use, and applying it to find current, voltage, and resistance.

Ohm's Law Definition

Ohm's Law states that the current (II) through a conductor between two points is directly proportional to the potential difference or voltage (VV) across the two points, and inversely proportional to the resistance (RR) between them.

Formulas

  • V=IRV = IR

  • I=VRI = \frac{V}{R}

  • R=VIR = \frac{V}{I}

Simple Circuit Components

  • Source (EMF): Electromotive force generated from a voltage source such as a battery (EE).

  • Load: Usually a resistor (RR).

  • Current (II): Produced only when the source is connected to the load in a close loop connection.

  • Voltage Drop (VdropV_{drop}): Appears when current (II) flows through a resistor (RR). The polarity of the voltage drop is inverse to the EMF (EE).

  • Formula for Voltage Drop: Vd=IRV_d = IR

Example 1.8: A circuit has a source of 15 V15\,V and a resistor of 10 Ω10\,\Omega.

  1. Current (II): I=VR=1510=1.5 AI = \frac{V}{R} = \frac{15}{10} = 1.5\,A

  2. Voltage Drop (VdropV_{drop}): Vdrop=IR=1.5×10=15 VV_{drop} = IR = 1.5 \times 10 = 15\,V

Self-Exercise Question Summary

  • Q1: Calculate time for 1 A1\,A to transfer 30 C30\,C.

    • Answer: 30 s30\,s.

  • Q2: Find resistivity of 2 m2\,m length, 500 Ω500\,\Omega resistance, 0.5 mm20.5\,mm^2 area.

    • Answer: 125 μΩm125\,\mu \Omega m.

  • Q3: Voltage for mixed connections:

    • (i) 5 V+11 V+4 V=20 V5\,V + 11\,V + 4\,V = 20\,V

    • (ii) Parallel cells of 44 V=44 V44\,V = 44\,V

    • (iii) Series (4+3)=7 V(4 + 3) = 7\,V; parallel with (2+5)=7 V(2 + 5) = 7\,V. Overall result is 7 V7\,V.

    • (iv) 3030 cells of 4 V4\,V in series = 120 V120\,V.

    • (v) 2020 cells of 14 V14\,V in parallel = 14 V14\,V.

    • (vi) Combination resulting in 50 V50\,V.

  • Q4: A 100 V100\,V battery causes 5 mA5\,mA current. Resistance?

    • Answer: R=1005×10−3=20 kΩR = \frac{100}{5 \times 10^{-3}} = 20\,k\Omega.

  • Q5: If voltage is reduced to 25 V25\,V on the same resistor, new current?

    • Answer: I=2520×103=1.25 mAI = \frac{25}{20 \times 10^3} = 1.25\,mA.