Field-Effect Transistors Study Notes
Introduction to Field-Effect Transistors
Fundamental Comparison with Bipolar Junction Transistors (BJTs):
Control Mechanism: The BJT transistor is a current-controlled device where the output collector current () is a direct function of the input base current (), defined by . The field-effect transistor (FET) is a voltage-controlled device where the output drain current () is controlled by the voltage applied across the input circuit (), defined by .

Charge Carriers: The BJT is a bipolar device because its conduction level depends on two charge carriers: electrons and holes. The FET is a unipolar device depending solely on single-carrier conduction—either electron conduction in n-channel devices or hole conduction in p-channel devices.
Electric Field Operating Principle: In a permanent magnet, a magnetic field envelopes metal filings and attracts them without physical contact. In an FET, an electric field is established by present charges, controlling the conduction path of the output circuit without requiring direct electrical contact between controlling and controlled quantities.
Input Impedance: One of the most critical advantages of the FET is its extremely high input impedance, ranging from to several hundred megohms. This far exceeds the typical input resistance levels of BJT configurations, making FETs exceptionally valuable in linear AC amplifier design.
Signal Sensitivity and Voltage Gain: BJTs exhibit higher sensitivity to changes in the applied signal, meaning the variation in output current is significantly greater in BJTs than in FETs for an equivalent change in applied voltage. Consequently, typical AC voltage gains for BJT amplifiers are much larger than for FET amplifiers.
Temperature Stability and Scale: FETs are more temperature-stable than BJTs and are generally smaller in physical size, making them particularly advantageous in integrated-circuit (IC) chips.
Handling Sensitivity: The structural characteristics of certain FET types (notably MOSFETs) make them more sensitive to static electricity handling than BJTs.
Primary Categories of Field-Effect Transistors:
Junction Field-Effect Transistor (JFET): A three-terminal device where input voltage controls output current via a reverse-biased p-n junction.
Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET): Subdivided into depletion-type and enhancement-type devices. Highly popular in computer integrated circuits due to thermal stability and circuit density.
Metal-Semiconductor Field-Effect Transistor (MESFET): Employs a Schottky barrier on Gallium Arsenide (GaAs) base material to maximize electron mobility and switching speed for RF and high-speed computer applications.
Historical Development:
Dr. Ian Munro Ross: Born in Southport, England; PhD from Gonville and Caius College, Cambridge University; President Emeritus of AT&T Bell Labs; Fellow of IEEE; Member of the National Science Board; Chairman of the National Advisory Committee on Semiconductors.
Dr. G. C. Dacey: Born in Chicago, Illinois; PhD from California Institute of Technology; Director of Solid-State Electronics Research at Bell Labs; Vice President of Research at Sandia Corporation; Member of IRE, Tau Beta Pi, and Eta Kappa Nu.
In 1955, Drs. Ross and Dacey jointly formulated an experimental procedure for measuring the physical operating characteristics of field-effect transistors.
Construction and Operating Characteristics of JFETs
Physical Structure of the n-Channel JFET:

Channel and Terminals: The primary structure consists of an n-type semiconductor material forming a conduction channel between embedded layers of p-type material.
Drain (): Connected to the top end of the n-type channel through an ohmic contact.
Source (): Connected to the bottom end of the n-type channel through an ohmic contact.
Gate (): Formed by connecting the two embedded p-type layers together to a common terminal.
No-Bias Junctions: In the absence of applied potentials, two p-n junctions exist under zero-bias conditions. A depletion region void of free charge carriers forms at each junction, preventing current flow across the junction.
Mechanical Water Analogy:

Applied Pressure: The voltage applied between Drain and Source () represents water pressure at the spigot.
Water Source / Flow: The spigot represents the Source (); the water stream represents the flow of electrons (charge carriers).
Drain: The drain basin collects charge flow.
Control Valve: The Gate terminal acts as a valve handle controlling the aperture size, thereby regulating charge flow to the drain.
Operating States and Internal Voltage Distribution:
Zero Gate Bias (, ):
Connecting Gate directly to Source establishes .
Applying positive voltage draws electrons to the Drain terminal, establishing conventional current flowing into the Drain ().
Current flow is uninhibited and limited purely by internal n-channel resistance.
Asymmetrical Depletion Width: The depletion region is wider near the top of both p-type materials.

Voltage Drop Explanation: Assuming uniform channel resistance, a voltage of drops linearly along the channel length ( near top, at center, near bottom). Because the Gate is tied to , the upper p-region is reverse-biased by , whereas the lower p-region is reverse-biased by only . Greater reverse bias broadens the depletion region near the Drain.
Zero Gate Current: Because the p-n junction is reverse-biased along its entire length, gate current is zero ().
Pinch-Off Condition (, ):
As increases, depletion regions expand until they approach each other near the Drain.
The voltage level that establishes this condition is defined as the pinch-off voltage ().
Pinch-off does not reduce current to ; instead, saturates at a maximum level designated as (Drain-to-Source current with Shorted gate).
Physical Reason: Complete current interruption would eliminate the potential drop along the channel required to sustain reverse bias, collapsing the depletion regions and restoring current.
For , the JFET behaves as a constant-current source where , while is dictated by external load conditions.
Negative Gate Bias ():
Applying a negative voltage to the Gate increases reverse bias across p-n junctions independently of .
Saturation is reached at lower levels, and saturated drain current drops progressively.

Cutoff: When (a negative voltage for n-channel e.g., ), drain current drops to . Data sheets designate this threshold as .
Voltage-Controlled Resistor Behavior:
To the left of the pinch-off locus (), the JFET operates in the ohmic or voltage-controlled resistance region.
Channel resistance is adjusted via applied gate voltage :
Where is channel resistance at , and is resistance at a specified .
Calculation Example: For an n-channel JFET with , , at :
p-Channel JFET Construction and Characteristics:
Constructed with a p-type channel between embedded n-type regions.
Voltage polarities and current directions are reversed: is positive, is negative.
Constriction increases with positive gate voltage; cutoff occurs at positive pinch-off voltage (e.g., ).
At excessively high , avalanche breakdown occurs; operational designs must maintain .
Circuit Symbols:

n-Channel: Gate arrow points IN toward the channel.
p-Channel: Gate arrow points OUT away from the channel.
JFET Transfer Characteristics and Shockley's Equation
Mathematical Derivation via Shockley's Equation:
Dr. William Bradford Shockley established the nonlinear parabolic relationship between input voltage and output current :
Biographical Note: Dr. Shockley was born in London, England; earned his PhD from Harvard in 1936; headed the Transistor Physics Department at Bell Laboratories; served as President of Shockley Transistor Corp; became Poniatoff Professor at Stanford; and received the 1956 Nobel Prize in Physics alongside Walter Brattain and John Bardeen.
The transfer curve defined by Shockley's equation is intrinsic to the device and independent of the external circuit network.
Key Mathematical Plot Points:
When , .
When , .
When , .
When , V_{GS} = 0.3 V_P$.\n\n* **Inverse Shockley Equation for Gate Voltage:**\n V_{GS} = V_P \left(1 - \sqrt{\frac{I_D}{I_{DSS}}}\right)\n * *Calculation Example:* Given I_{DSS} = 8\,\text{mA}V_P = -4\,\text{V}V_{GS}I_D = 4.5\,\text{mA}:\n V_{GS} = -4\,\text{V} \left(1 - \sqrt{\frac{4.5\,\text{mA}}{8\,\text{mA}}}\right) = -4\,\text{V} (1 - \sqrt{0.5625}) = -4\,\text{V}(1 - 0.75) = -1\,\text{V}\n\n* **Worked Plotting Examples:**\n * *Example 6.1 (n-channel):* Given I_{DSS} = 12\,\text{mA}V_P = -6\,\text{V}.\n * V_{GS} = 0\,\text{V} \rightarrow I_D = 12\,\text{mA}\n * V_{GS} = -1.8\,\text{V} \,(0.3 V_P) \rightarrow I_D = 6\,\text{mA} \,(I_{DSS}/2)\n * V_{GS} = -3.0\,\text{V} \,(0.5 V_P) \rightarrow I_D = 3\,\text{mA} \,(I_{DSS}/4)\n * V_{GS} = -6.0\,\text{V} \,(V_P) \rightarrow I_D = 0\,\text{mA}\n * *Example 6.2 (p-channel):* Given I_{DSS} = 4\,\text{mA}V_P = +3\,\text{V}.\n * V_{GS} = 0\,\text{V} \rightarrow I_D = 4\,\text{mA}\n * V_{GS} = +0.9\,\text{V} \,(0.3 V_P) \rightarrow I_D = 2\,\text{mA}\n * V_{GS} = +1.5\,\text{V} \,(0.5 V_P) \rightarrow I_D = 1\,\text{mA}\n * V_{GS} = +3.0\,\text{V} \,(V_P) \rightarrow I_D = 0\,\text{mA}\n\n# JFET Data Sheets, Instrumentation, and Comparison with BJTs\n\n* **JFET Specification Sheet Analysis (Fairchild 2N5457 / MMBF5457):**\n * **Packages:** Available in TO-92 (through-hole, higher power dissipation) and SOT-23 (surface mount). Source and Drain terminals are interchangeable.\n * **Maximum Ratings:** V_{DS} = 25\,\text{V}V_{DG} = 25\,\text{V}V_{GS} = -25\,\text{V}I_{GF} = 10\,\text{mA}T_J, T_{\text{stg}} = -55\,^\circ\text{C}\text{ to }+150\,^\circ\text{C}.\n * **Power Dissipation & Derating:** Total dissipation P_D = V_{DS} I_D = 625\,\text{mW}350\,\text{mW}T_A = 25\,^\circ\text{C}5.0\,\text{mW}/^\circ\text{C}2.8\,\text{mW}/^\circ\text{C}25\,^\circ\text{C}.\n * **Electrical Characteristics:** Gate-Source Breakdown Voltage V_{(BR)GSS} = -25\,\text{V}V_{GS(\text{off})} = -0.5\,\text{V}\text{ to }-6.0\,\text{V}I_{DSS} = 1.0\,\text{mA}\text{ to }5.0\,\text{mA}.\n * **Linear Operating Boundary:** Defined by saturation locus (V_{DS\,\text{sat}}I_{DSS}V_{DS\,\text{max}}P_D = V_{DS} I_D$.
Curve Tracer Instrumentation Parameter Estimation:
For a 2N4416 JFET on a curve tracer set to vertical, horizontal, :
Top curve () gives .
Locating curve point where yields .
Calculate pinch-off voltage: .
JFET vs BJT Analytical Relationships Comparison:
JFET: , , . Analysis initiates with and solving for .
BJT: , , . Analysis initiates with and solving for I_B$.\n\n# Depletion-Type MOSFETs\n\n* **Basic Physical Construction:**\n * \n * **Substrate:** Base slab formed of p-type silicon substrate (SS).\n * **Channel and Contacts:** n-doped Drain and Source regions linked by a built-in physical n-channel.\n * **Insulated Gate:** The Gate metallic contact is completely insulated from the n-channel by a thin Silicon Dioxide (\text{SiO}_2) dielectric layer.\n * **Dielectric Isolation:** Eliminates direct electrical connection between Gate and channel, establishing extremely high input impedance (R_i \ge 10^{10}\,\Omega10^{12}\,\OmegaI_G \approx 0\,\text{A}.\n\n* **Modes of Operation:**\n * **Depletion Mode (V_{GS} < 0\,\text{V} for n-channel):**\n * Negative gate potential repels channel electrons into substrate and attracts minority holes toward \text{SiO}_2 interface.\n * Recombination reduces free carrier density, decreasing I_D.\n * At V_{GS} = V_PI_D = 0\,\text{mA}). Obeys Shockley's equation.\n * **Zero-Bias State (V_{GS} = 0\,\text{V}):**\n * Current conducts freely, saturating at I_D = I_{DSS}.\n * **Enhancement Mode (V_{GS} > 0\,\text{V} for n-channel):**\n * Positive gate potential attracts additional free electrons from p-substrate into channel, increasing carrier concentration.\n * Raises I_DI_{DSS}.\n * Shockley's equation remains valid for positive V_{GS}.\n * *Calculation Example (Ex 6.3):* Given I_{DSS} = 10\,\text{mA}V_P = -4\,\text{V}V_{GS} = +1\,\text{V}:\n I_D = 10\,\text{mA} \left(1 - \frac{+1\,\text{V}}{-4\,\text{V}}\right)^2 = 10\,\text{mA} (1 + 0.25)^2 = 10\,\text{mA} (1.5625) = 15.63\,\text{mA}\n\n* **p-Channel Depletion MOSFET:**\n * Constructed with n-type substrate and built-in p-channel.\n * Voltage polarities reversed (V_{DS} < 0\,\text{V}V_{GS} > 0\,\text{V}V_{GS} < 0\,\text{V} for enhancement).\n\n* **Symbols and Data Sheet Ratings (2N3797):**\n * Symbol features a unbroken channel line separated from gate line by dielectric space.\n * Motorola 2N3797 Ratings: V_{DS} = 20\,\text{V}V_{GS} = \pm 10\,\text{V}I_D = 20\,\text{mA}P_D = 200\,\text{mW}V_{GS(\text{off})} = -5.0\text{ to }-7.0\,\text{V}I_{DSS} = 2.0\text{ to }6.0\,\text{mA}I_{D(\text{on})} = 9.0\text{ to }18\,\text{mA}V_{GS} = +3.5\,\text{V}V_{DS} = 10\,\text{V}.\n\n# Enhancement-Type MOSFETs\n\n* **Basic Construction:**\n * \n * **Substrate & Contacts:** p-type silicon substrate (SS) with diffused n-doped Drain and Source regions.\n * **Absence of Built-In Channel:** Unlike depletion MOSFETs, there is NO constructed channel between Drain and Source.\n * **Zero Gate Bias Behavior:** At V_{GS} = 0\,\text{V}V_{DS}I_D = 0\,\text{A} (only p-n junction leakage current of ~nA flows) because two back-to-back p-n junctions oppose current flow.\n\n* **Channel Formation and Induced Conduction:**\n * Applying positive V_{GS} > 0\,\text{V}\text{SiO}_2.\n * Attracts minority electrons from p-substrate to \text{SiO}_2 boundary surface.\n * **Threshold Voltage (V_TV_{GS(\text{Th})}):** Minimum gate-to-source voltage required to accumulate sufficient electron density to form an induced n-channel supporting measurable current.\n * **Pinch-Off and Saturation:**\n * For V_{GS} > V_TV_{DS}V_{DG} = V_{DS} - V_{GS}.\n * Saturation voltage: V_{DS\,\text{sat}} = V_{GS} - V_T$.
Enhancement Transfer Equation:
for V_{GS} < V_T$.\n * *Calculation Example (Ex 6.4 - Motorola 2N4351):* Given V_{GS(\text{Th})} = 3\,\text{V}I_{D(\text{on})} = 3\,\text{mA}V_{GS(\text{on})} = 10\,\text{V}:\n k = \frac{3\,\text{mA}}{(10\,\text{V} - 3\,\text{V})^2} = \frac{3\,\text{mA}}{49\,\text{V}^2} = 0.061 \times 10^{-3}\,\text{A/V}^2\n I_D = 0.061 \times 10^{-3} (V_{GS} - 3\,\text{V})^2\n * At V_{GS} = 5\,\text{V}I_D = 0.244\,\text{mA}.\n * At V_{GS} = 8\,\text{V}I_D = 1.525\,\text{mA}.\n * At V_{GS} = 10\,\text{V}I_D = 3.0\,\text{mA}.\n * At V_{GS} = 12\,\text{V}I_D = 4.94\,\text{mA}.\n * At V_{GS} = 14\,\text{V}I_D = 7.38\,\text{mA}.\n\n* **p-Channel Enhancement MOSFET:**\n * n-type substrate, p-doped regions, requires negative threshold voltage (V_T < 0\,\text{V}V_{GS} < V_T).\n\n* **Circuit Symbols:**\n * Dashed vertical channel line reflecting the absence of a built-in physical channel.\n\n# MOSFET Handling and Protection Safeguards\n\n* **Electrostatic Discharge (ESD) Hazards:**\n * The ultra-thin \text{SiO}_2 dielectric layer easily punctures if static electricity produces high voltage across Gate and Channel.\n\n* **Mandatory Handling Precautions:**\n * Keep conductive shorting ring/foil around leads until device is soldered or inserted.\n * Ground operator hands and tools prior to handling; pick up device strictly by metal casing.\n * Never insert or remove devices from a circuit board while power is ON (prevents inductive voltage transients).\n\n* **Internal Zener Protection:**\n * Integrated back-to-back Zener diodes connected between Gate and Source (e.g., 30\,\text{V} ratings).\n * If voltage transient exceeds \\pm 30\,\text{V}\30\,\text{V}0\,\text{V}), limiting peak gate voltage to \\pm 30\,\text{V}\.\n * Minor drawback: Slightly reduces input resistance due to Zener reverse leakage, but remains extremely high for circuit applications.\n\n# Power MOSFETs: VMOS and UMOS Architectures\n\n* **Limitations of Standard Planar MOSFETs:**\n * Planar MOSFETs are limited in power dissipation (typically < 1\,\text{W}) and current rating.\n\n* **Vertical Construction Advantages:**\n * \n * Channel is oriented vertically, causing current to flow vertically from top source contacts through p-region into n^+ substrate (Drain).\n * **VMOS (V-Groove MOSFET):** V-shaped cut etched into semiconductor structure. Channel length defined by thin vertical p-layer height (1\text{--}2\,\mu\text{m}).\n * Provides two parallel conduction paths, dramatically lowering ON-resistance (R_{\text{on}}).\n * Handles current in amperes and power exceeding 10\,\text{W}.\n * *Drawbacks of VMOS:* V-groove etching precision issues cause threshold voltage instability; sharp V-tip creates high localized electric fields lowering breakdown voltage.\n * **UMOS (Trench MOSFET):**\n * Replaces V-groove with U-shaped trench using DRAM memory trench etching.\n * Trench width 2\text{--}10\,\mu\text{m}2\,\mu\text{m}\sim 1\,\mu\text{m}.\n * Achieves lower R_{\text{on}}3.1\text{--}11.5\,\text{m}\Omega10\,\text{V}) and higher breakdown limits.\n * Input gate capacitance (C_{iss} = C_{GS}1400\,\text{pF}4600\,\text{pF}100\,\text{kHz}.\n\n* **Key Thermal and Switching Benefits:**\n * **Positive Temperature Coefficient:** Unlike BJTs, vertical power MOSFETs have a positive temperature coefficient for resistance. If device temperature rises, resistance increases, automatically reducing drain current and eliminating thermal runaway.\n * **Fast Switching Speed:** Reduced charge storage yields switching times less than half those of BJTs.\n\n# Complementary MOSFET (CMOS) Logic\n\n* **Structure and Inverter Operation:**\n * Pairs p-channel and n-channel MOSFETs on a single silicon substrate.\n * **CMOS Inverter Schematic Logic:**\n * p-channel (Q_2V_{SS} = +5\,\text{V}.\n * n-channel (Q_10\,\text{V}).\n * Both Gates tied to input V_iV_o$.
High Logic Input (, 1-state):
turns ON (very low resistance ).
turns OFF (extremely high resistance ).
Output (0-state).
Low Logic Input (, 0-state):
turns OFF (high resistance ).
turns ON (low resistance ).
Output (1-state).
Power Efficiency: Power dissipation in static states is nearly zero because one transistor in the series path is always turned OFF, restricting current to tiny substrate leakage values (~nA).
Metal-Semiconductor Field-Effect Transistors (MESFETs)
Schottky Barrier Gate Structure:
Replaces insulated dielectric oxide () with a direct metal-semiconductor junction (Schottky barrier, e.g., tungsten deposited on n-type Gallium Arsenide / GaAs).
Eliminating dielectric insulator drastically reduces physical distance between gate metal and channel, minimizing gate-to-channel stray capacitance.
Utilizes high carrier mobility of GaAs to enable superior RF and ultra-high-speed computer performance.
Exclusive n-Channel Availability:
Because hole mobility in GaAs is relatively low compared to electron mobility, p-channel MESFETs lack high-speed benefits.
Therefore, only n-channel MESFETs are commercially produced.
Channel lengths are extremely small ().
Types:
Depletion MESFET: Built-in n-channel; obeys same transfer equations as depletion MOSFETs/JFETs.
Enhancement MESFET: No initial channel; positive threshold voltage limited to because the gate Schottky barrier diode turns on forward-biased at .
Summary Table of Field-Effect Transistors
JFET (n-Channel):
Basic Relationships: , ,
Transfer Curve Range: ranges from to ; ranges from to .
Input Parameters: , .
MOSFET Depletion-Type (n-Channel):
Basic Relationships: , ,
Transfer Curve Range: ranges from negative through into positive enhancement region (); extends above .
Input Parameters: , .
MOSFET Enhancement-Type (n-Channel):
Basic Relationships: , , ,
Transfer Curve Range: for ; rises exponentially for .
Input Parameters: , .
MESFET Depletion-Type (n-Channel):
Basic Relationships: , ,
Transfer Curve Range: Similar to depletion MOSFET/JFET.
Input Parameters: , .
MESFET Enhancement-Type (n-Channel):
Basic Relationships: , ,
Transfer Curve Range: Positive limited to .
Input Parameters: , .