CPL Principles of Flight and Performance Notes

Units and Measurements in Aeroscience

  • The International System (SI) Units: Used in modern aviation as derived from the metric system.

    • Length: metre (mm)

    • Mass: kilogram (kgkg)

    • Time: second (ss)

    • Temperature: degrees Celsius (°C^°C) or Kelvin (KK)

  • Derived SI Units:

    • Force: Newton (NN)

    • Pressure: Pascal (PaPa)

    • Power: watt (WW)

  • Aviation-Specific Non-SI Units:

    • Foot (ftft): Used for altitude.

    • Nautical mile (nmnm): Used for distance.

    • Knot (ktkt): Units of speed equivalent to nautical miles per hour.

    • Horsepower (HpHp): Used to measure engine power.

Scalar and Vector Quantities

  • Scalar Quantities: These provide information only regarding magnitude or size (e.g., 100 m\text{e.g., } 100\,m).

  • Vector Quantities: These provide both magnitude and direction (e.g., 100 m South\text{e.g., } 100\,m \text{ South}).

  • Resolving Vectors: Vectors must be resolved into two components that are at 90-degree angles to each other.

Motion Definitions and Formulas

  • Speed: The distance traveled divided by the time taken (e.g., 100 kph\text{e.g., } 100\,kph).     v=dtv = \frac{d}{t}

  • Velocity: The distance traveled in a specific direction divided by time (e.g., 250 degrees at 20 kt\text{e.g., } 250\text{ degrees at } 20\,kt).

  • Acceleration: A change in velocity over time (a=Δvta = \frac{\Delta v}{t}). Acceleration occurs through a change in speed or a change in direction.

Newton’s Laws of Motion

  • First Law (Inertia): An object remains at rest or in constant uniform motion unless acted upon by an external force (FF). An aircraft on a runway requires the external force of thrust to change its state from rest to acceleration.

  • Second Law (Acceleration): The force required to accelerate an object is the product of its mass and the desired acceleration.     F=maF = ma     Comparing a C152 and an A320 Airbus, the A320 has over 300 times more mass; therefore, it requires substantially more thrust to achieve meaningful acceleration.

  • Third Law (Action and Reaction): For every action, there is an equal and opposite reaction. A propeller pushes air backward with significant force, resulting in the forward propulsion of the aircraft (thrust).

Mass, Weight, and Momentum

  • Inertia: The tendency of an object to resist changes in its state of motion. It is solely dependent on mass.

  • Mass vs. Weight:

    • Mass is the amount of matter in an object, measured in kgkg.

    • Weight is a force resulting from mass and gravity, measured in Newtons (NN).     W=mgW = mg     If an object has a mass of 70 kg70\,kg on Earth, its weight is 70×9.81=686.7 N70 \times 9.81 = 686.7\,N.

  • Gravity: The average acceleration due to Earth's gravity is 9.81 m/s29.81\,m/s^2.

  • Momentum: The Difficulty of stopping an object or changing its direction, calculated as the product of mass and velocity. A 1,000 kg1,000\,kg train at 10 m/s10\,m/s has the same momentum (10,000 kg⋅m/s10,000\,kg \cdot m/s) as a 1 kg1\,kg bullet at 10,000 m/s10,000\,m/s.

Curved Path Motion and Moments

  • Centripetal Force (CPF): The center-seeking force required for an object to move along a curved path.     CPF=mv2rCPF = \frac{mv^2}{r}

  • Centrifugal Reaction (CFR): The equal and opposite reaction to centripetal force that acts to pull an object out of a turn.

  • Moments: A turning force about a pivot point. The strength of a moment is the product of the force and the arm (distance) from the pivot. In the SI system, this is measured in Newton-metres (NmNm).

  • Couple and Torque: A couple consists of two equal but opposite forces acting around a midpoint. The resulting turning force is called Torque.

Equilibrium and Energy

  • Translational Equilibrium: Occurs when all forces are balanced (e.g., Lift = Weight and Thrust = Drag). In this state, an aircraft maintains constant speed and direction.

  • Rotational Equilibrium: Occurs when an object rotates at a constant rate (RPM). For a propeller, engine torque must be balanced by propeller torque.

  • Centre of Gravity (CoG): The point from which the weight of an object is said to act. If suspended from its CoG, the aircraft will not rotate.

  • Work: Done when a force moves an object a distance (1 Nm=1 Joule1\,Nm = 1\text{ Joule}).     W=FdW = Fd

  • Power: The rate at which work is performed.     P=Wt=FdtP = \frac{W}{t} = \frac{Fd}{t}

  • Energy Types:

    • Potential Energy: Based on position (height). An aircraft at 10,000 ft10,000\,ft has high potential energy compared to one at 10 ft10\,ft.

    • Kinetic Energy: Based on motion (velocity).

Atmospheric Properties

  • Density Factors: Air density is proportional to pressure and inversely proportional to temperature and humidity.

    • Humidity: High humidity reduces density because water molecules take up more space and are less dense than air molecules.

    • Pressure: Reducing pressure reduces density.

    • Temperature: Reducing temperature increases density.

  • Standard Atmosphere (ISA) Conditions:

    • Sea level pressure: 1013.25 hPa1013.25\,hPa

    • Sea level temperature: 15∘C15^\circ C

    • Pressure lapse rate: Approx 1 hPa1\,hPa per 30 ft30\,ft up to 5,000 ft5,000\,ft.

    • Temperature lapse rate: 1.98∘C1.98^\circ C per 1,000 ft1,000\,ft up to the tropopause.

    • Tropopause: The altitude where temperature becomes isothermal at −56.5∘C-56.5^\circ C.

  • Density Altitude (DA): The altitude in ISA conditions that corresponds to the local air density. A high density altitude day (low density) causes aircraft to perform as if they were at a higher altitude.

  • Viscosity: The "stickiness" of a fluid. Air is a viscous fluid and has the ability to stick to surfaces.

Basic Aerodynamic Theory

  • Pressure Types:

    • Freestream Static Pressure: Exerted equally and perpendicularly on all surfaces within the atmosphere.

    • Dynamic Pressure: The pressure felt due to movement through the atmosphere.

    • Kinetic Energy of Air: Calculated as Ek=12mv2E_k = \frac{1}{2} m v^2. In aerodynamics, air density (ρ\rho) is substituted for mass.

    • Air Velocity Formula:     q=12ρV2q = \frac{1}{2} \rho V^2

  • Airspeed Definitions:

    • Indicated Airspeed (IAS): The reading on the Air Speed Indicator (ASI).

    • Calibrated Airspeed (CAS): IAS corrected for pressure error (instrument/position error).

    • Equivalent Airspeed (EAS): CAS corrected for compressibility error, which becomes significant at high speeds.

    • True Airspeed (TAS): EAS corrected for relative density. If relative density is half of the sea level value (at roughly 20,000 ft20,000\,ft), EAS is approximately 71%71\% of TAS (0.5≈0.71\sqrt{0.5} \approx 0.71).

Aerofoil Geometry and Airflow

  • Leading Edge: The front part of the wing.

  • Trailing Edge: The rear part of the wing.

  • Chord Line: A straight line connecting the leading and trailing edges.

  • Chord: The distance measured along the chord line.

  • Thickness: The depth of the aerofoil, usually max at 30-40%30\text{-}40\% aft of the leading edge.

  • Thickness/Chord Ratio: Max thickness as a percentage of chord (GP aerofoils: 10-12%10\text{-}12\%, high speed: 7%7\%, high lift: 15-17%15\text{-}17\%).

  • Camber: The curvature of the aerofoil.

  • Relative Airflow (RAF): Airflow moving in the direction opposite to the aircraft's path.

  • Angle of Attack (AoA): The angle between the RAF and the chord line.

Bernoulli’s Theorem and Venturi Effect

  • Theorem: In the streamline flow of an ideal fluid, the sum of position energy, motion energy (dynamic), and pressure energy is constant.     Velocity+Pressure=Constant\text{Velocity} + \text{Pressure} = \text{Constant}

  • Venturi Effect: In a converging duct, air accelerates, causing a decrease in pressure energy to maintain the constant total energy. In a diverging duct, air slows and pressure increases.

  • Upwash and Downwash: Upwash is the upward flow ahead of the wing; downwash is the downward flow behind the wing.

Aerodynamic Forces: Lift and Drag

  • Lift: The component of the Total Aerodynamic Reaction (TR) acting at 90 degrees to the RAF, opposing weight.

  • Drag: The component of TR acting parallel to the RAF, opposing the aircraft's motion.

  • Centre of Pressure (CP): The point where lift is concentrated. As AoA increases, the CP moves forward until roughly 12∘12^\circ. Near the stall (15-16∘15\text{-}16^\circ), it moves rapidly rearward to 50%50\% chord.

  • Lift Formula:     L=CL12ρV2SL = C_L \frac{1}{2} \rho V^2 S

    • CLC_L: Coefficient of lift (lifting capability).

    • ρ\rho: Air density.

    • VV: Velocity (IAS).

    • SS: Wing surface area.

  • Coefficient of Lift (CLC_L) Curve:

    • Zero Lift Angle: The AoA where lift is zero (Symmetrical: 0∘0^\circ, GP: −4∘-4^\circ, High Lift: −6∘-6^\circ).

    • Stall Angle: The AoA where CLC_L peaks (CLmaxC_{L\text{max}}), typically around 16∘16^\circ.

Vortex Formation and Induced Drag

  • Three-Dimensional Flow: High relative pressure underneath the wing escapes around the wingtips toward the low pressure on top, creating spanwise flow.

  • Vortices: The meeting of spanwise and chordwise flows results in trailing edge vortices and large wingtip vortices.

  • Induced Downwash: Wingtip vortices push the RAF downward at the trailing edge, creating an effective RAF. This results in an effective AoA that is smaller than the geometric AoA.

  • Aspect Ratio (AR): The ratio of wingspan to chord. Higher AR reduces induced drag and increases CLC_L.     AR=spanchordAR = \frac{\text{span}}{\text{chord}}

Components of Drag

  • Total Drag: parasite drag (DpD_p) + induced drag (DiD_i).

  • Parasite Drag: Drag not related to lift production.

    • Skin Friction: Caused by air viscosity and shear stress in the boundary layer. Affected by speed, surface roughness, and wetted area.

    • Form Drag: Caused by the pressure differential between forward-facing and rearward-facing surfaces. Reduced by streamlining.

    • Interference Drag: Caused by airflows meeting at angles (e.g., wing and fuselage). Reduced by fairings.

  • Induced Drag: Drag created as a byproduct of lift. It decreases as airspeed increases.

  • Boundary Layer:

    • Laminar: Thin (2 mm2\,mm), smooth flow.

    • Turbulent: Thicker (2 cm2\,cm), features eddies and swirls. Transition occurs at the transition point due to an adverse pressure gradient.

Lift Augmentation

  • Trailing Edge Flaps: Used to increase CLmaxC_{L\text{max}} and reduce stall speed.

    • Basic: Small lift increase, high drag increase.

    • Split: Large lift increase, very large drag increase.

    • Slotted: Substantial lift increase, low drag.

    • Fowler: Highest lift increase, lowest drag increase.

  • Leading Edge Devices: Slats and slots re-energize the boundary layer, increasing the stalling AoA and nose attitude.

  • Spoilers: Also called lift dumpers, these disrupt airflow over the wing to reduce lift and increase drag during landing.

Flight Controls and Stability

  • Axes of Rotation:

    • Longitudinal Axis: Nose to tail; movement is Roll (Ailerons).

    • Lateral Axis: Wingtip to wingtip; movement is Pitch (Elevators).

    • Normal Axis: Ceiling to floor; movement is Yaw (Rudder).

  • Secondary Effects:

    • Aileron secondary effect is Yaw (due to tilted lift and keel surface strike).

    • Rudder secondary effect is Roll (due to one wing moving faster and generating more lift).

  • Adverse Yaw Countermeasures:

    • Frise Ailerons: Upgoing aileron protrudes into the airflow to create drag.

    • Differential Ailerons: Upgoing aileron moves further than the downgoing aileron.

    • Coupled Controls: Rudder and ailerons move together.

  • Control Balance:

    • Aerodynamic Balance: Moves the CP closer to the hinge line (e.g., inset hinges, horn balance).

    • Mass Balance: Weights placed ahead of the hinge line to prevent control flutter.

Stalling and Spinning

  • The Stall:surpassing the critical AoA (16∘16^\circ). Airflow becomes a turbulent wake and lift is insufficient to maintain flight.

  • Factors Increasing Stall Speed: increased weight, increased load factor (steep turns), power off, wing contamination.

  • Wing-Drop: One wing stalling before the other. Encouraged by aileron use near the stall, unbalanced flight, or rigging errors.

    • Washout: reducing the angle of incidence at the wingtips to keep them unstalled longer.

  • The Spin: A state of autorotation where both wings are stalled, but one more deeply than the other. Recovery involves putting power to idle, neutralizing ailerons, and applying full opposite rudder.

Performance in Various Flight Regimes

  • Straight and Level: Lift equals Weight; Thrust equals Drag.

  • Climb Speeds:

    • VxV_x: Best Angle of Climb (max height per ground distance).

    • VyV_y: Best Rate of Climb (max height per time).

  • Ceilings:

    • Service Ceiling: The altitude where a piston aircraft's max rate of climb is 100 fpm100\,fpm.

    • Absolute Ceiling: The altitude where the rate of climb is 0 fpm0\,fpm.

  • Glide: For maximum glide range, the pilot must maintain the best L/D ratio speed (approx 4∘4^\circ AoA). Weight does not affect glide angle, but requires a higher glide speed.

  • Turning Performance:

    • Load Factor: Increases with bank angle (60∘ bank=2g60^\circ \text{ bank} = 2g).

    • Stall Speed in a Turn: increases by the square root of the load factor (Vsn=VsnV_{sn} = V_s \sqrt{n}).

Propeller Principles

  • Blade Geometry:

    • Blade Angle: Angle between chord and plane of rotation.

    • Helical Twist: Reduction in blade angle from root to tip to maintain uniform AoA.

  • Efficiency:

    • Geometric Pitch: Advance distance at zero AoA.

    • Experimental Mean Pitch (EMP): Advance distance when producing zero thrust.

    • Slip: The difference between EMP and actual advance. Max efficiency occurs at 30%30\% slip.

  • Variable Pitch Propellers: A Constant Speed Unit (CSU) maintains set RPM by adjusting blade pitch. To increase power: Mixture Rich -> Increase RPM -> Increase Manifold Pressure (MAP).

  • Effects:

    • P-Factor (Asymmetric Blade Effect): In high AoA, the downgoing blade produces more thrust, causing yaw.

    • Torque Reaction: Engine tries to roll the plane opposite to prop rotation.

    • Gyroscopic Precession: A force applied to the rotating prop is felt 90 degrees later in the rotation.

Range and Endurance

  • Range: The distance flown per unit of fuel (Specific Air Range - SAR). Achieved at the speed for minimum drag (Max L/D).     SAR=TASGFCSAR = \frac{\text{TAS}}{\text{GFC}}

  • Endurance: Maximum time in the air for fuel used. Achieved at the speed for minimum power (bottom of the power required curve).

  • Efficiency: Range depends on Specific Fuel Consumption (SFC). Best range/endurance is improved by leaning the mixture and operating at the lowest permitted RPM with high MAP.

Regulatory and Terminal Performance

  • Take-Off Terms:

    • TODR: Distance to reach a screen height of 50 ft50\,ft (35 ft35\,ft for some commercial ops) at Take-Off Safety Speed (TOSS).

    • TORA: Suitable runway length for the ground run.

    • ASDA: Effective length for an aborted takeoff, including stopway.

  • Landing Terms:

    • LDR: Distance from 50 ft50\,ft above threshold to full stop with max braking.

  • Runway Surface Conditions:

    • Wet: Reflective water present.

    • Contaminated: Over 25%25\% of area covered by >3 mm>3\,mm of water, slush, or snow.

  • Calculations:

    • Pressure Altitude: Standard height corrected for non-standard pressure (1 hPa=30 ft1\,hPa = 30\,ft).

    • Density Altitude: Pressure altitude corrected for temperature deviation (1∘C=120 ft1^\circ C = 120\,ft).