University Study Notes: Reinforced Concrete Design to Eurocode 2

Introduction to Reinforced Concrete Design and Material Properties

  • The Design Process: Design is characterized by an iterative loop across three main stages:

    • Conceptual Design: Establishing the design brief, ground conditions, building usage (insulation, fire, performance), and evaluating alternative structural forms and materials.
    • Preliminary Design: Using approximate hand calculations, span-to-depth ratios, and layout sketches to assess the viability of conceptual solutions.
    • Detailed Design: Full structural analysis and refinement of calculations, resulting in documentation for cost and construction.
  • Sustainability and HS&O (Health, Safety, and Welfare):

    • Sustainability: Concrete provides high thermal mass for energy efficiency and can utilize waste products like fly ash. Locally sourced materials reduce CO2 emissions.
    • HS&W: Complies with the Construction Design and Management (CDM) regulations. Designers must eliminate hazards and reduce risks during the design phase.
  • Composite Action Principles:

    • Concrete is strong in compression but weak in tension (tension strength is approximately 10% of compression strength).
    • Steel provides tensile strength and shear resistance.
    • Strain Compatibility: Assuming a perfect bond (often enhanced by ribbed bars), the strain in the steel reinforcement is identical to the strain in the adjacent concrete: "epsilons="epsilonc"epsilon_{s} = "epsilon_{c}.
    • Thermal Expansion: Coefficients are similar for both materials (7×10−67 \times 10^{-6} to 12×10−612 \times 10^{-6} per degree Celsius), preventing bond failure from differential expansion.
  • Concrete Material Properties:

    • Strength Classes: Based on the 28-day characteristic cylinder strength (fckf_{ck}). For example, Class C25/30 has a cylinder strength of 25 N/mm225\,N/mm^2 and a cube strength of 30 N/mm230\,N/mm^2.
    • Modulus of Elasticity (EcmE_{cm}): The secant modulus is used for short-term effects. The relationship with the dynamic modulus (EdE_d) is approximated as: Ecm=(1.25Ed−19) kN/mm2E_{cm} = (1.25E_d - 19)\,kN/mm^2.
    • Creep: Continuous deformation under sustained load. Final deformation can be 3 to 4 times the initial elastic deformation.
    • Shrinkage: Caused by hydration heat and moisture loss. Calculated steel stress (fscf_{sc}) due to restrained shrinkage: fsc="epsiloncsEs1+"alphaeAs/Acf_{sc} = \frac{"epsilon_{cs} E_s}{1 + "alpha_e A_s / A_c}, where "alphae=Es/Ecm"alpha_e = E_s / E_{cm}.

Limit State Design Principles

  • Primary Limit States:

    • Ultimate Limit State (ULS): Ensures safety against collapse, buckling, or overturning.
    • Serviceability Limit State (SLS): Focuses on limiting deflection, cracking, vibration, and ensuring durability and fire resistance.
  • Characteristic Values:

    • Characteristic Strength (fkf_k): The value below which 5% of test results are expected to fall: fk=fm−1.64sf_k = f_m - 1.64s.
    • Characteristic Actions: Divided into Permanent (GkG_k) and Variable (QkQ_k). Wind (WkW_k) is treated as a separate variable category.
  • Partial Safety Factors (γ\gamma):

    • Materials ("gammam"gamma_m): For ULS Persistent/Transient: Concrete = 1.501.50, Steel = 1.151.15. For Accidental: Concrete = 1.201.20, Steel = 1.001.00.
    • Actions ("gammaf"gamma_f):
      • Unfavourable Permanent (GkG_k) = 1.351.35.
      • Favourable Permanent (GkG_k) = 1.001.00.
      • Unfavourable Leading Variable (QkQ_k) = 1.501.50.
  • Load Combinations (SLS):

    • Combination Value: Ed=∑Gk,j+Qk,1+∑"psi0,iQk,iE_d = \sum G_{k,j} + Q_{k,1} + \sum "psi_{0,i} Q_{k,i}.
    • Frequent Value: Ed=∑Gk,j+"psi1,1Qk,1+∑"psi2,iQk,iE_d = \sum G_{k,j} + "psi_{1,1} Q_{k,1} + \sum "psi_{2,i} Q_{k,i}.
    • Quasi-permanent Value: Ed=∑Gk,j+∑"psi2,iQk,iE_d = \sum G_{k,j} + \sum "psi_{2,i} Q_{k,i}.

Structural Analysis of Reinforced Concrete

  • Analysis Methods: Includes moment and shear coefficients, manual moment distribution, and computer-aided frame analysis.
  • Moments and Shears in Beams:
    • Span AB uniform load (ww) shear: VAB=wL2−MAB−MBALV_{AB} = \frac{wL}{2} - \frac{M_{AB} - M_{BA}}{L}.
    • Maximum span moment occurs at zero shear: Mmax=VAB22w+MABM_{max} = \frac{V_{AB}^2}{2w} + M_{AB}.
  • Redistribution of Moments: EC2 allows an elastic analysis to be modified to account for plastic behavior.
    • Required for ductility: Neutral axis depth (xx) is restricted based on redistribution ("delta"delta): x/d≤("delta−k1)/k2x/d \le ("delta - k_1)/k_2.
    • UK Annex values: k1=0.4k_1 = 0.4, k2=1.0k_2 = 1.0. Standard EC2 values: k1=0.44k_1 = 0.44, k2=1.25k_2 = 1.25.

Analysis of the Section

  • Rectangular Stress Block: Simplified for ULS design. Depth s=0.8xs = 0.8x, with uniform stress 0.567fck0.567 f_{ck}.
  • Singly Reinforced Sections:
    • Non-dimensional factor: K=Mbd2fckK = \frac{M}{bd^2 f_{ck}}.
    • Lever arm: z=d[0.5+0.25−K/1.134]z = d[0.5 + \sqrt{0.25 - K/1.134}].
    • Limiting Kbal=0.167K_{bal} = 0.167 for concrete classes up to C50/60 (where x=0.45dx = 0.45d).
    • Area of steel: As=M0.87fykzA_s = \frac{M}{0.87 f_{yk} z}.
  • Doubly Reinforced Sections (K>0.167K > 0.167):
    • Compression steel area: As′=(K−Kbal)fckbd20.87fyk(d−d′)A'_s = \frac{(K - K_{bal}) f_{ck} b d^2}{0.87 f_{yk} (d - d')}.
    • Tension steel area: As=Kbalfckbd20.87fykzbal+As′A_s = \frac{K_{bal} f_{ck} b d^2}{0.87 f_{yk} z_{bal}} + A'_s.
  • Flanged Sections (T and L beams):
    • Effective width (beffb_{eff}): beff=bw+∑beff,ib_{eff} = b_w + \sum b_{eff,i}, where beff,i=0.2bi+0.1l0≤0.2l0b_{eff,i} = 0.2b_i + 0.1l_0 \le 0.2l_0.
    • Stress block usually lies in the flange. If s>hfs > h_f, web compression must be calculated.

Shear, Bond, and Torsion

  • Shear Design (Variable Strut Inclination):
    • Diagonal concrete strut angle ("theta"theta) is limited: 22∘≤"theta≤45∘22^{\circ} \le "theta \le 45^{\circ}.
    • Maximum resistance (concrete crushing): VRd,max=0.36bwd(1−fck/250)fck(cot"theta+tan"theta)V_{Rd,max} = \frac{0.36 b_w d (1 - f_{ck}/250) f_{ck}}{(cot "theta + tan "theta)}.
    • Shear links area: "fracAsws=VEd0.78dfykcot"theta"frac{A_{sw}}{s} = \frac{V_{Ed}}{0.78 d f_{yk} cot "theta}.
    • Additional longitudinal force due to shear: "DeltaFtd=0.5VEdcot"theta"Delta F_{td} = 0.5 V_{Ed} cot "theta.
  • Anchorage and Laps:
    • Basic anchorage length: lb,rqd=("phi/4)(σsd/fbd)l_{b,rqd} = ("phi/4) (\sigma_{sd} / f_{bd}).
    • Ultimate bond stress: fbd=2.25"eta1"eta2fctdf_{bd} = 2.25 "eta_1 "eta_2 f_{ctd}.
    • Laps: l0=lb,rqd×"alpha1"alpha2"alpha3"alpha5"alpha6l_0 = l_{b,rqd} \times "alpha_1 "alpha_2 "alpha_3 "alpha_5 "alpha_6.
  • Torsion: Based on a thin-walled box model.
    • Shear flow: q=T/(2Ak)q = T / (2 A_k).
    • Additional longitudinal steel: As1=TEdukcot"theta2Ak(0.87fyk)A_{s1} = \frac{T_{Ed} u_k cot "theta}{2 A_k (0.87 f_{yk})}.

Serviceability Requirements

  • Cover for Durability and Fire: Nominal cover cnom=cmin+"Deltacdevc_{nom} = c_{min} + "Delta c_{dev}.
    • cminc_{min} based on exposure class (XC, XD, XS, XF, XA) and structural class.
    • Standard fire resistance periods (R60 to R240) determine minimum member dimensions and axis distances (aa).
  • Deflection Control: Managed via span-to-effective depth ratios (L/dL/d).
    • Basic ratio depends on reinforcement ratio ("rho"rho). Limiting ratio = Basic Ratio ×\times Correction Factors.
    • Correction factors account for span > 7m, flanged sections, and excess reinforcement.
  • Crack Control:
    • Max crack width (wkw_k) is usually 0.3 mm0.3\,mm (building) or 0.2 mm0.2\,mm (prestressed/water tanks).
    • wk=sr,max("epsilonsm−"epsiloncm)w_k = s_{r,max} ("epsilon_{sm} - "epsilon_{cm}).
    • Maximum crack spacing: sr,max=3.4c+0.425k1k2"phi/"rhop,effs_{r,max} = 3.4c + 0.425 k_1 k_2 "phi / "rho_{p,eff}.

Prestressed Concrete

  • Methods:
    • Pre-tensioning: Tendons stretched before casting; force transferred by bond.
    • Post-tensioning: Tendons tensioned against hardened concrete; force transferred by mechanical anchors.
  • Serviceability Analysis: Stresses must stay within limits at transfer and service.
    • Magnel Diagram: A graphical tool plotting 1/P01/P_0 against eccentricity (ee) to find a solution that satisfies all four stress inequalities.
  • Prestress Losses: Calculated for elastic shortening, creep, shrinkage, steel relaxation, and (for post-tensioning) friction and anchorage slip.

Foundations and Retaining Walls

  • Pad Footings: Sized for uniform soil pressure p=N/BDp = N/BD. Reinforced for bending and checked for punching shear at 2.0d2.0d from the column face.
  • Piled Foundations: Vertical loads distributed based on group geometry: Pn=N/n±(Mxyn/Ix)±(Myxn/Iy)P_n = N/n \pm (M_x y_n / I_x) \pm (M_y x_n / I_y).
  • Retaining Walls: Analysis includes stability against overturning (0.9Gkx≥"gammafHky0.9G_k x \ge "gamma_f H_k y) and sliding ("muGk≥"gammafHk"mu G_k \ge "gamma_f H_k).