Paper 1

1. MECHANICAL PROPERTIES OF MATERIALS

Mechanical properties describe how a material behaves when forces are applied to it.

Strength: Ability to withstand an applied force without breaking or deforming. Example: steel used in structural frames.

Tensile strength: Ability to resist being pulled apart. Example: steel cables used in suspension bridges.

Compressive strength: Ability to withstand forces that squeeze or crush it. Example: concrete used in building foundations.

Hardness: Resistance to scratching, indentation and surface wear. Example: hardened steel used in cutting tools.

Toughness: Ability to absorb energy and resist breaking when subjected to impact. Example: polycarbonate used in protective safety visors.

Brittleness: Tendency to fracture or shatter without significant deformation. Example: glass.

Ductility: Ability to be stretched and drawn into wires without breaking. Example: copper electrical wiring.

Malleability: Ability to be hammered or rolled into thin sheets without cracking. Example: aluminium drinks cans.

Elasticity: Ability to return to its original shape after a force is removed, provided its elastic limit has not been exceeded. Example: springs made from spring steel.

Plasticity: Ability to undergo permanent deformation without breaking. Example: clay being shaped into a ceramic product.

Stiffness: Resistance to bending or deformation when a force is applied. Example: carbon fibre bicycle frames.

Resilience: Ability to absorb energy when deformed and release it when the force is removed. Example: rubber shock absorbers.

Fatigue resistance: Ability to withstand repeated loading and unloading without developing cracks or failing. Example: aircraft components.

Creep: Slow, permanent deformation of a material under a constant load over a prolonged period. Example: plastic shelving gradually bending under heavy objects.

Key distinction: Strength is resistance to failure; stiffness is resistance to deformation; toughness is resistance to fracture under impact.

2. PHYSICAL PROPERTIES OF MATERIALS

Physical properties describe characteristics of a material that can be measured or observed without changing its chemical composition.

Density: Mass per unit volume. Low-density materials are useful when lightweight products are required. Example: aluminium used in aircraft.

Thermal conductivity: Ability to transfer heat. Copper has high thermal conductivity, making it suitable for saucepans and heat exchangers.

Electrical conductivity: Ability to allow electrical current to pass through a material. Copper is widely used in electrical wiring.

Thermal insulation: Ability to resist the transfer of heat. Expanded polystyrene is used in insulation and packaging.

Electrical insulation: Ability to resist the flow of electrical current. PVC is used to insulate electrical cables.

Melting point: Temperature at which a solid becomes a liquid. This affects the temperature and processes needed for manufacturing.

Corrosion resistance: Ability to resist deterioration caused by chemical reactions with the environment. Stainless steel resists corrosion because of its chromium content.

Permeability: Ability of a material to allow liquids or gases to pass through it. Important when designing waterproof packaging.

Transparency: Allows light to pass through clearly. Example: acrylic display cases.

Translucency: Allows light through but does not allow objects to be seen clearly. Example: frosted acrylic lighting covers.

Opacity: Does not allow light to pass through. Example: MDF furniture panels.

UV resistance: Ability to withstand ultraviolet radiation without significant deterioration. Important for outdoor furniture and products.

3. PERFORMANCE CHARACTERISTICS OF MATERIALS3.1 Wood, veneers and melamine formaldehyde laminatesNatural timber

Timber is obtained from trees and is classified into hardwoods and softwoods.

Softwood: Comes from coniferous trees, usually evergreen trees with needles. Generally grows faster and is often cheaper.

Examples:

  • Pine – affordable, lightweight and easy to machine; used in furniture and construction.

  • Spruce – lightweight and relatively strong; used in construction and musical instruments.

  • Cedar – naturally resistant to decay and insects; used for outdoor furniture and cladding.

  • Douglas fir – strong and relatively durable; used for structural construction.

  • Redwood – attractive grain and good natural resistance to decay.

  • Larch – relatively durable and suitable for exterior applications.

Hardwood: Comes from broad-leaved trees. Often slower growing, with a variety of attractive grain patterns and good durability.

Examples:

  • Oak – strong, durable and attractive grain; used for tables, flooring and furniture.

  • Ash – tough and flexible; used for tool handles, sports equipment and furniture.

  • Beech – hard, smooth and easy to machine; used for kitchen utensils and chairs.

  • Teak – naturally oily and moisture resistant; used for outdoor furniture and boat construction.

  • Mahogany – attractive reddish-brown appearance and good workability; used in high-quality furniture.

  • Birch – pale, relatively strong and easy to work; used in furniture and plywood.

Manufactured boards

Manufactured boards are made by bonding wood fibres, particles or veneers together using adhesives and pressure.

Plywood

  • Made from thin layers of wood veneer glued together.

  • Each layer is positioned with its grain at approximately 90 degrees to the previous layer.

  • Cross-graining improves strength and dimensional stability.

  • Advantages: strong, stable, available in large sheets and less likely to split.

  • Disadvantages: edges may need covering; quality varies.

  • Uses: furniture, cabinets, flooring and construction.

Marine plywood

  • Manufactured using durable veneers and water-resistant adhesive.

  • Designed to resist moisture and delamination.

  • Used in boats and exterior applications.

  • It is not automatically waterproof or immune to decay; appropriate sealing is still needed.

Aeroply

  • Lightweight plywood made from thin veneers, commonly using lightweight woods.

  • Used where low weight is important, such as model aircraft and prototypes.

Flexible plywood

  • Thin plywood designed to bend around curved forms.

  • Used for curved furniture, display units and architectural features.

Chipboard

  • Made from wood chips and particles bonded with resin under heat and pressure.

  • Advantages: cheap, uses wood waste and available in large sheets.

  • Disadvantages: edges can crumble, relatively weak screw-holding properties and poor moisture resistance unless specially treated.

  • Uses: flat-pack furniture and kitchen carcasses.

MDF – Medium Density Fibreboard

  • Made from fine wood fibres mixed with resin and compressed under heat.

  • Smooth, uniform surface with no visible grain.

  • Easy to cut, machine, paint and route.

  • Disadvantages: heavy, produces fine dust during machining and can swell when wet.

  • Uses: painted furniture, shelving, cabinet doors and interior decorative panels.

Veneers

A veneer is a very thin slice of natural timber bonded to another material, commonly MDF or plywood.

  • Provides the appearance of expensive natural timber without using solid hardwood throughout.

  • Can improve appearance and reduce material costs.

  • Used in furniture, doors, cabinets and decorative panels.

  • Can be produced from oak, walnut, ash and other timbers.

  • Disadvantages: thin surface can be damaged by sanding, moisture or impact.

Example: IKEA furniture may use wood-effect surfaces or veneer finishes to create a timber appearance at a lower cost than solid hardwood.

Melamine formaldehyde laminates

Melamine formaldehyde (MF) is a thermosetting resin used to produce hard, durable decorative surfaces.

  • Melamine-impregnated paper is bonded to a substrate such as chipboard.

  • Heat and pressure create a hard, smooth surface.

  • Resistant to scratches, stains, heat and everyday wear.

  • Available in different colours, patterns and wood-effect finishes.

  • Easy to clean and relatively inexpensive.

  • Disadvantages: edges can chip, and damage to the surface is difficult to repair.

Product example: Melamine-faced chipboard used in IKEA wardrobes, desks and kitchen furniture.

Important timber performance characteristics

  • Grain pattern: visual arrangement of fibres, influencing appearance.

  • Grain direction: affects strength, splitting and machining.

  • Warping: distortion caused by uneven moisture changes.

  • Shrinkage: timber becomes smaller as it loses moisture.

  • Splitting: timber separates along its grain.

  • Decay: deterioration caused by fungi and moisture.

  • Moisture resistance: ability to withstand exposure to water.

  • Machining qualities: ease of cutting, drilling, sanding and shaping.

Timber stock forms:

  • Rough sawn – cut timber with an uneven, unfinished surface.

  • PSE (Planed Square Edge) – timber planed on all sides to give straight, square edges.

  • PAR (Planed All Round) – timber planed on all four sides for a smooth finish.

  • Mouldings – timber shaped into decorative or functional profiles.

3.2 Polymers – thermoplastic and thermosetting

Polymers are materials made from long chains of repeating molecular units called monomers.

Thermoplastics

Thermoplastics soften when heated and harden when cooled. This process can be repeated, allowing them to be remoulded and recycled, depending on polymer type and contamination.

Examples:

LDPE – Low Density Polyethylene

  • Flexible, lightweight and resistant to moisture.

  • Used for plastic bags, squeeze bottles and packaging film.

  • Easily processed and relatively inexpensive.

  • Can be difficult to recycle through some collection systems.

HDPE – High Density Polyethylene

  • Stronger and more rigid than LDPE.

  • Resistant to chemicals and moisture.

  • Used for milk bottles, detergent bottles and water pipes.

PP – Polypropylene

  • Lightweight, tough and fatigue resistant.

  • Resistant to many chemicals.

  • Used for food containers, living hinges and reusable storage boxes.

  • Example: plastic lunch boxes and hinged bottle caps.

HIPS – High Impact Polystyrene

  • Modified polystyrene with improved impact resistance.

  • Easy to thermoform and relatively inexpensive.

  • Used in refrigerator liners, product packaging and model-making sheets.

ABS – Acrylonitrile Butadiene Styrene

  • Tough, rigid and impact resistant.

  • Good surface finish and easy to mould.

  • Used for LEGO bricks, protective equipment and electronic housings.

PMMA – Polymethyl Methacrylate (acrylic/Perspex)

  • Transparent, lightweight and weather resistant.

  • Can be polished and line bent.

  • Used for display cases, signage, lighting covers and aquarium panels.

  • More brittle and scratch-prone than polycarbonate.

Nylon (polyamide)

  • Strong, tough and wear resistant.

  • Low friction and good abrasion resistance.

  • Used for gears, bearings, cable ties and textiles.

PVC – Polyvinyl Chloride

  • Available in rigid and flexible forms.

  • Resistant to chemicals and weathering.

  • Rigid PVC: pipes, window frames and cable trunking.

  • Flexible PVC: electrical cable insulation and flexible tubing.

PET – Polyethylene Terephthalate

  • Transparent, lightweight and strong.

  • Good barrier properties against gases and moisture.

  • Used for drinks bottles, food trays and packaging.

  • Widely recyclable where suitable facilities exist.

Thermosetting polymers

Thermosetting polymers undergo an irreversible chemical reaction when heated and cured. They form permanent cross-linked structures and cannot be remelted and reshaped.

Urea formaldehyde (UF)

  • Hard, rigid and electrically insulating.

  • Used for electrical fittings, plugs and adhesives for manufactured boards.

  • Can be brittle.

Melamine formaldehyde (MF)

  • Hard, durable and scratch resistant.

  • Used for decorative laminates, kitchen worktop surfaces and tableware.

Polyester resin

  • Can be combined with glass fibres to make GRP.

  • Used in boat hulls, car body panels and fibreglass products.

  • Good for producing complex shapes.

Epoxy resin

  • Strong adhesive and resin system.

  • Good chemical and moisture resistance.

  • Used in structural bonding, composite products and protective coatings.

Thermoplastics vs thermosets

Thermoplastics

Thermosets

Soften when heated

Do not remelt

Can be remoulded

Permanently set

Usually easier to recycle mechanically

More difficult to recycle

Often have linear or branched chains

Have cross-linked molecular structures

Examples: ABS, PP, PET

Examples: epoxy, MF, UF

3.3 Biodegradable polymers

Biodegradable polymers are polymers that can be broken down by biological activity, often involving microorganisms and enzymes, under suitable conditions.

Some also degrade through exposure to water, heat or UV light.

PLA – Polylactic acid / Polylactide

  • Made from renewable plant-based feedstocks, such as corn starch or sugar.

  • Can be moulded or formed into packaging and 3D printing filament.

  • Used in disposable food packaging, cups and 3D printing.

  • Industrial composting may be required; it does not necessarily break down quickly in ordinary soil or home compost.

PHA – Polyhydroxyalkanoates

  • Produced by microorganisms.

  • Can biodegrade in suitable natural environments.

  • Used in packaging and disposable products.

  • Often more expensive to produce than conventional plastics.

Corn starch polymers

  • Made using starch from crops.

  • Can be used in packaging and films.

  • Can biodegrade under suitable conditions.

PotatoPak

  • Packaging material made using potato starch.

  • Can be used as an alternative to some expanded polystyrene protective packaging.

  • Designed to break down under suitable composting conditions.

Biopol

  • A biodegradable polymer material associated with polyhydroxybutyrate (PHB).

  • Used as an example of biodegradable plastic technology.

Lactel / water-soluble polymer products

  • Lactel is associated with biodegradable poly(lactide-co-glycolide) materials.

  • Water-soluble polymer films can be used for applications such as detergent pods and packaging.

  • Water-soluble does not automatically mean environmentally harmless.

Advantages:

  • Can reduce reliance on fossil-based raw materials.

  • May reduce long-term plastic waste in appropriate disposal systems.

  • Can be manufactured into films and 3D shapes.

Disadvantages:

  • Some require industrial composting.

  • Can be more expensive.

  • May contaminate conventional recycling streams.

  • Biodegradation depends on environmental conditions.

3.4 Composites

A composite is made by combining two or more different materials to produce improved properties.

Usually consists of:

  • Matrix – the material that surrounds and holds everything together.

  • Reinforcement – material that improves strength, stiffness or other properties.

CFRP – Carbon Fibre Reinforced Plastic

  • Carbon fibres embedded in a resin matrix.

  • Extremely high strength-to-weight ratio.

  • Stiff, lightweight and strong.

  • Expensive and difficult to recycle.

  • Uses: Formula One cars, aerospace components and high-performance bicycles.

GRP – Glass Reinforced Plastic

  • Glass fibres combined with polyester or epoxy resin.

  • Lightweight, strong, corrosion resistant and mouldable.

  • Uses: boat hulls, water tanks, car body panels and roofing.

Tungsten carbide

  • Tungsten carbide particles combined with a metallic binder, commonly cobalt.

  • Extremely hard and wear resistant.

  • Used in drill bits, cutting tools and industrial machinery.

Aluminium composite board

  • Usually consists of two thin aluminium sheets bonded to a central core.

  • Lightweight, rigid and flat.

  • Used for building cladding, signage and display panels.

Reinforced concrete

  • Concrete combined with steel reinforcement bars.

  • Concrete resists compression but is weak in tension.

  • Steel reinforcement provides tensile strength.

  • Used in bridges, buildings and foundations.

Fibre cement

  • Cement combined with reinforcing fibres.

  • Durable, weather resistant and relatively fire resistant.

  • Used in exterior cladding, roofing and building panels.

Glulam – Glued Laminated Timber

  • Layers of timber bonded together using structural adhesive.

  • Strong, stable and can be manufactured into curved beams.

  • Used in large roofs, bridges and architectural structures.

Advantages of composites:

  • High strength-to-weight ratio.

  • Can combine useful properties from different materials.

  • Can be formed into complex shapes.

Disadvantages:

  • Can be expensive.

  • Difficult to separate and recycle.

  • Repair may require specialist knowledge.

3.5 Ferrous metals only

Ferrous metals contain iron as their main constituent. They are often strong and widely used in construction and manufacturing.

Low carbon steel (mild steel)

  • Contains a relatively low percentage of carbon.

  • Ductile, malleable, tough and easy to weld.

  • Relatively inexpensive.

  • Can rust without protective finishes.

  • Uses: car bodies, furniture frames, brackets and construction.

Medium carbon steel

  • Contains more carbon than mild steel.

  • Stronger and harder but less ductile.

  • Can be heat treated.

  • Uses: gears, shafts and engineering components.

High speed steel (HSS)

  • Alloy steel designed to retain hardness at high temperatures.

  • Resists wear and heat during cutting.

  • Uses: drill bits, milling cutters and lathe tools.

Stainless steel

  • Contains chromium, which forms a protective oxide layer.

  • Corrosion resistant, strong and hygienic.

  • Uses: cutlery, kitchen equipment, surgical instruments and appliances.

  • More expensive than mild steel.

Cast iron

  • High carbon iron alloy.

  • Hard, brittle and excellent in compression.

  • Good vibration damping and wear resistance.

  • Uses: engine blocks, manhole covers and traditional cookware.

Metal enhancement: heat treatments

Case hardening

  • The surface of low-carbon steel is made harder while the core remains relatively tough.

  • Increases wear resistance without making the entire component brittle.

  • Used for gears, shafts and other moving components.

Hardening

  • Steel is heated to the correct temperature and then rapidly cooled (quenched).

  • Increases hardness and strength.

  • Can make steel brittle.

Tempering

  • Hardened steel is reheated to a lower temperature and cooled.

  • Reduces brittleness and increases toughness.

  • Usually follows hardening.

4. FORMING, REDISTRIBUTION AND ADDITION PROCESSES4.1 Polymer processesVacuum forming

  1. A thermoplastic sheet is clamped into a frame.

  2. It is heated until soft.

  3. The sheet is lowered over or onto a mould.

  4. Air is removed by vacuum, pulling the sheet against the mould.

  5. It cools and retains the shape.

  6. Excess material is trimmed.

Advantages:

  • Relatively low-cost tooling.

  • Suitable for large, thin-walled products.

  • Good for batch and mass production.

Disadvantages:

  • Limited detail compared with injection moulding.

  • Material thickness can become uneven.

  • Requires trimming and produces waste.

Examples: food trays, bath panels, packaging and refrigerator liners.

Thermoforming

  • A thermoplastic sheet is heated until pliable and formed using a mould.

  • Vacuum forming and pressure forming are types of thermoforming.

  • Used for packaging, vehicle interior panels and product housings.

Calendaring

  • Heated polymer is passed between a series of rollers.

  • Produces continuous sheets or films of controlled thickness.

  • Used for PVC flooring, vinyl sheets and plastic films.

  • Suitable for continuous large-scale production.

Line bending

  • A thermoplastic sheet is heated along a narrow line using a heating element.

  • The softened area is bent to the required angle and held until cool.

  • Used for acrylic display stands, signage and covers.

  • Simple and useful for small batches, but only produces bends along selected lines.

Laminating / lay-up

  • Layers of reinforcement, such as glass or carbon fibre, are placed into a mould.

  • Resin is added to bond the layers.

  • The composite is cured to create a rigid product.

  • Used for GRP boats, car body panels and carbon fibre components.

  • Can produce complex shapes, but labour and curing time can be high.

Injection moulding

  1. Polymer granules are fed into a heated barrel.

  2. A rotating screw melts and moves the polymer.

  3. Molten polymer is injected into a closed mould under pressure.

  4. The polymer cools and solidifies.

  5. The mould opens and the product is ejected.

Advantages:

  • High accuracy and repeatability.

  • Fast cycle times.

  • Suitable for complex shapes and mass production.

  • Low unit cost at high volumes.

Disadvantages:

  • Expensive moulds and machinery.

  • High initial investment.

  • Less economical for very small production runs.

Examples: LEGO bricks, bottle caps, plastic chairs and phone cases.

Blow moulding

  1. A heated tube of polymer called a parison is placed inside a mould.

  2. Compressed air is blown into it.

  3. The polymer expands against the mould walls.

  4. It cools and is removed.

Used for hollow products such as plastic bottles, fuel tanks and containers.

Rotational moulding

  1. A measured amount of polymer powder is placed inside a hollow mould.

  2. The mould is heated while rotating around two axes.

  3. The molten polymer coats the inside of the mould.

  4. It cools while rotating and is removed.

Advantages:

  • Suitable for large hollow products.

  • Relatively low tooling costs.

  • Produces fairly uniform wall thickness.

Disadvantages:

  • Slow cycle times.

  • Limited dimensional accuracy compared with injection moulding.

Examples: water tanks, kayaks, storage containers and playground equipment.

Extrusion

  • Polymer granules are heated and forced through a shaped die.

  • Produces continuous lengths with a consistent cross-section.

  • The product is cooled and cut to length.

Examples: PVC pipes, plastic window frames, cable insulation and plastic tubing.

Compression moulding

  1. A measured amount of polymer or moulding compound is placed into a heated mould.

  2. The mould closes and applies pressure.

  3. Heat and pressure cause the material to flow and cure.

  4. The product is removed.

Often used for thermosetting materials.

Examples: electrical plugs, handles and electrical switch components.

Advantages: suitable for strong, relatively thick products and thermosets.

Disadvantages: slower cycle times than many injection moulding processes and may produce flash requiring trimming.

4.2 Wood processesLaminating

  • Thin layers of timber are glued together over a former or mould.

  • Clamped until adhesive cures.

  • Produces strong curved or shaped components.

  • Used for laminated furniture, curved chair backs and glulam beams.

Steam bending

  1. Timber is placed inside a steam box.

  2. Steam heats and softens the timber fibres.

  3. The timber is bent around a former.

  4. It is held in position until cool and dry.

Advantages:

  • Creates curved timber without cutting away large amounts of material.

  • Maintains continuous grain.

Disadvantages:

  • Requires suitable timber and specialist equipment.

  • Can split if bent too sharply.

Examples: curved chair components and boat ribs.

Turning between centres

  • A piece of timber is held between two centres on a wood lathe.

  • The timber rotates while a cutting tool shapes it.

  • Used for cylindrical products such as table legs, handles and spindles.

Chuck and faceplate turning

  • A chuck grips the workpiece, while a faceplate supports larger or irregular pieces.

  • Used to turn bowls, plates and decorative objects.

  • Requires correct mounting and safe balancing.

Milling

  • A rotating cutter removes material to create slots, grooves and shaped surfaces.

  • Used for accurately machining timber components.

Routering

  • A router uses a rotating cutter to remove material.

  • Produces grooves, rebates, holes, edges and decorative profiles.

  • Used for cabinet doors, joints and furniture components.

5. METAL PROCESSES AND METAL JOINING5.1 Metal forming

Press forming

  • Sheet metal is placed between a punch and die.

  • A press applies force to shape the metal.

  • Used for car body panels, appliance casings and metal brackets.

  • Suitable for batch and mass production with appropriate tooling.

Spinning

  • A metal disc rotates on a lathe against a shaped former.

  • A tool progressively pushes the metal into the required shape.

  • Used for lampshades, bowls and metal cookware.

Cupping

  • A flat metal blank is pressed into a cup-shaped die.

  • Used to produce shallow hollow components and as a stage in deep drawing.

Deep drawing

  • A metal sheet blank is drawn into a die by a punch.

  • Produces hollow products with significant depth.

  • Used for kitchen sinks, metal cans and car components.

Forging

  • Metal is shaped using compressive forces, usually when hot.

  • Improves grain flow and can produce strong components.

  • Used for tools, shafts and engineering components.

Drop forging

  • A heated metal blank is shaped by repeated blows from a falling hammer or press.

  • Suitable for strong, repeated components.

  • Used for spanners, connecting rods and crankshafts.

Bending

  • Metal is permanently deformed around a straight or curved axis.

  • Used for brackets, frames, pipes and sheet metal enclosures.

Rolling

  • Metal passes between rollers to reduce thickness or change its cross-section.

  • Used to produce sheet metal, plate, bars and structural sections.

Casting

Sand casting

  • Molten metal is poured into a mould made from sand.

  • Once solidified, the sand mould is broken to remove the casting.

  • Suitable for large and relatively complex components.

  • Examples: engine blocks and manhole covers.

Die casting

  • Molten metal is forced under pressure into a reusable metal die.

  • Suitable for high-volume manufacture of accurate components.

  • Examples: aluminium housings, automotive parts and appliance components.

Investment casting

  • A wax pattern is coated in a ceramic material.

  • The wax is melted out, leaving a cavity.

  • Molten metal is poured into the cavity.

  • Produces intricate, accurate shapes.

  • Examples: turbine blades and precision engineering parts.

Low-temperature casting

  • A low-melting-point metal, such as pewter, is melted and poured into a mould.

  • Used for ornaments, badges and decorative products.

5.2 Metal joining

MIG welding – Metal Inert Gas

  • An electric arc melts the metal and a continuously fed wire electrode.

  • Shielding gas protects the weld from atmospheric contamination.

  • Fast and suitable for production work.

  • Used for vehicle frames, gates and steel structures.

TIG welding – Tungsten Inert Gas

  • Uses a non-consumable tungsten electrode.

  • An inert shielding gas protects the weld.

  • Filler rod may be added separately.

  • Produces precise, high-quality welds.

  • Used for stainless steel, aluminium and thin metal components.

Spot welding

  • Two metal sheets are pressed between copper electrodes.

  • Electrical current produces heat that forms a weld at the contact point.

  • Used extensively in car body manufacture.

Oxy-acetylene welding

  • Oxygen and acetylene gases produce a high-temperature flame.

  • Used to melt and join metals.

  • Can also be used for cutting and heating.

  • Useful for repair and fabrication work.

Soft soldering

  • A low-melting-point filler metal joins components without melting the main materials.

  • Used for electrical connections and small metal components.

  • Generally produces weaker joints than brazing.

Hard soldering

  • Uses higher temperatures than soft soldering.

  • A stronger filler metal creates the joint.

  • Used in plumbing and metalwork.

Brazing

  • A filler metal melts and flows into the joint, while the parent metals remain solid.

  • Produces strong joints and is useful for dissimilar metals.

  • Used in bicycle frames, pipes and tools.

Riveting

  • A rivet is inserted through aligned holes and its end is deformed to secure the components.

  • Creates a permanent mechanical joint.

  • Used in aircraft structures and sheet metal products.

Temporary metal fixings

Self-tapping screws: Create their own thread when driven into a suitable material.

Machine screws: Used with a pre-threaded hole or nut.

Nuts and bolts: Secure components together and can be dismantled for maintenance or repair.

5.3 Wood joining

Dovetail joint

  • Interlocking wedge-shaped pins and tails.

  • Very strong resistance to being pulled apart.

  • Used for drawers and quality cabinetmaking.

Comb joint

  • Also called a finger joint.

  • Interlocking rectangular fingers are glued together.

  • Provides a large gluing surface.

  • Used for boxes, furniture and timber extensions.

Housing joint

  • A groove is cut into one piece of timber to receive another.

  • Used for shelves fitted into bookcases and cabinets.

Half-lap joint

  • Half the thickness of each piece is removed so they overlap flush.

  • Used for frames and cross-bracing.

Dowel joint

  • Cylindrical wooden dowels fit into corresponding holes in two components.

  • Usually glued.

  • Used in furniture and cabinets.

Mortise and tenon

  • A projecting tenon fits into a matching mortise hole.

  • Strong joint commonly used in chair frames, tables and doors.

Component joining

Knock-down (KD) fittings

  • Allow furniture to be assembled and disassembled.

  • Examples: cam locks, connector bolts and barrel nuts.

  • Used in flat-pack furniture, such as IKEA products.

Wood screws: Join timber components and can usually be removed for repair.

Nuts and bolts: Provide strong removable joints, often used in larger furniture and structures.

Coach bolts: Heavy-duty bolts with a rounded head and square section beneath, commonly used in timber construction.

5.4 Adhesives

PVA (polyvinyl acetate)

  • Water-based adhesive commonly used for wood.

  • Easy to apply, inexpensive and dries clear.

  • Requires clamping while curing.

  • Not all formulations are suitable for exterior or wet conditions.

Contact adhesive

  • Applied to both surfaces and allowed to become tacky before joining.

  • Provides an immediate bond when surfaces are pressed together.

  • Used for laminates, rubber and some upholstery materials.

  • Difficult to reposition after contact.

UV-hardening adhesive

  • Cures when exposed to ultraviolet light.

  • Useful for bonding transparent materials such as glass and acrylic.

  • Requires light to reach the adhesive for curing.

Solvent cement – Tensol / acrylic cement

  • Softens the surfaces of acrylic components so they fuse together.

  • Produces clear joints.

  • Used for acrylic display cases and signage.

Epoxy resin

  • Usually consists of resin and hardener mixed together.

  • Produces a strong, durable bond.

  • Can bond different materials.

  • Used for metal, wood and composite repairs.

5.5 Jigs and fixtures

Jig: A device that holds and guides a tool or workpiece so operations can be repeated accurately.

Examples:

  • Drill jig – guides a drill bit to create holes in the correct positions.

  • Router jig – guides a router along a specific path.

  • Dowelling jig – ensures dowel holes line up accurately.

Fixture: A device that securely holds and locates a workpiece during manufacturing. It does not necessarily guide the cutting tool.

Examples:

  • Welding fixture – holds metal parts in the correct position during welding.

  • Milling fixture – holds a component securely during machining.

Benefits:

  • Improve accuracy and consistency.

  • Reduce human error.

  • Speed up repeated manufacture.

  • Improve safety by securing workpieces.

  • Reduce waste and production costs.

Limitations: Initial design and manufacture costs time and money; a jig or fixture may only suit a particular component.

6. THE USE OF FINISHES6.1 Wood finishing

Finishes improve the appearance of timber and protect it from moisture, wear and decay.

Polyurethane varnish

  • Hard-wearing protective coating.

  • Resistant to scratches and moisture.

  • Used on flooring, tables and furniture.

  • Available in gloss, satin and matt.

Acrylic varnish

  • Often water-based.

  • Dries relatively quickly and provides a protective surface.

  • Used on furniture and decorative timber products.

Water-based paint

  • Provides colour and surface protection.

  • Lower odour than many solvent-based paints.

  • Used on interior furniture and timber products.

Wood stain

  • Adds colour while allowing the grain to remain visible.

  • Used on furniture, doors and flooring.

  • Usually requires an additional protective finish.

Colour wash

  • Thin, diluted colour coating that allows the grain to show through.

  • Used for decorative effects.

Wax

  • Creates a smooth, natural-looking surface.

  • Easy to apply and maintain.

  • Less durable and water resistant than many varnishes.

Danish oil

  • Penetrates timber and enhances its grain.

  • Provides a natural-looking finish.

  • Requires maintenance and periodic reapplication.

Teak oil

  • Used to nourish and protect suitable hardwoods.

  • Commonly applied to outdoor timber furniture and boat-related timber.

  • Needs regular maintenance.

Pressure treatment

  • Preservative chemicals are forced into timber under pressure.

  • Helps protect against fungal decay and insect attack.

  • Used for outdoor decking, fencing and garden structures.

6.2 Paper finishing

Laminating

  • A protective plastic film is bonded to paper or card.

  • Improves durability and moisture resistance.

  • Used for menus, ID cards and packaging.

Embossing

  • Raises a design above the surface using pressure and a die.

  • Creates a textured, premium appearance.

  • Used on business cards, book covers and packaging.

Debossing

  • Presses a design into the surface, creating an indented effect.

  • Used for luxury packaging and stationery.

Varnishing

  • Applies a clear coating to improve appearance and protect the printed surface.

  • Can add gloss or matt effects.

UV varnishing

  • A varnish is cured using ultraviolet light.

  • Produces a durable and often glossy surface.

Spot UV varnishing

  • UV varnish is applied to selected areas only.

  • Creates contrast between coated and uncoated areas.

  • Used on luxury product packaging and promotional materials.

Foil blocking

  • Uses heat and pressure to transfer metallic or coloured foil onto paper or card.

  • Creates a premium decorative finish.

  • Used on invitations, book covers and cosmetics packaging.

6.3 Paper and board printing processes

Screen printing

  • Ink is pushed through a mesh screen onto a surface.

  • A stencil blocks areas where ink should not pass.

  • Suitable for bold designs and printing on different materials.

  • Used for posters, textiles and promotional products.

  • Can be economical for repeated designs but each colour may need a separate screen.

Flexographic printing

  • Uses flexible raised printing plates and fast-drying inks.

  • Suitable for continuous printing on flexible materials.

  • Used for food packaging, carrier bags and labels.

  • Efficient for large production runs.

Offset lithographic printing

  • Ink is transferred from a printing plate to a rubber blanket and then onto paper.

  • Produces high-quality, consistent images.

  • Suitable for large print runs.

  • Used for magazines, books and brochures.

Digital printing

  • Transfers a digital image directly onto a surface.

  • No printing plate is needed.

  • Economical for short runs and personalised printing.

  • Used for posters, packaging prototypes and business cards.

  • Can have a higher cost per item for very large runs compared with offset printing.

6.4 Metal finishing

Cellulose paint

  • Traditional quick-drying paint that forms a protective surface.

  • Used for metal products and vehicle finishes.

Acrylic paint

  • Provides colour and protection.

  • Can be used on suitably prepared metal surfaces.

Electroplating

  • Uses an electric current to deposit a thin layer of metal onto another metal.

  • Improves appearance and can improve corrosion resistance.

  • Examples: chrome-plated taps and nickel-plated components.

Dip coating

  • A component is dipped into a liquid coating and removed.

  • The coating is allowed to drain and cure.

  • Used for protective and decorative finishes.

Powder coating

  • Electrostatic powder is applied to a component and heated to form a durable coating.

  • Produces an even finish and good corrosion protection.

  • Used on bicycle frames, metal furniture and appliances.

Galvanising

  • Coats steel or iron with zinc to prevent corrosion.

  • Commonly achieved through hot-dip galvanising.

  • Used for fencing, outdoor structures and steel components.

Sealants and preservatives

  • Applied to protect surfaces from environmental damage and corrosion.

Anodising

  • An electrochemical process that thickens the natural oxide layer on aluminium.

  • Improves corrosion resistance and allows coloured finishes.

  • Used on aluminium window frames, phone housings and bicycle components.

Plating

  • Covers a metal surface with another metal to improve appearance or performance.

  • Examples: silver plating and chrome plating.

Cathodic protection

  • Prevents corrosion by making the protected metal the cathode of an electrochemical cell.

  • Can use a sacrificial anode, such as zinc or magnesium.

  • Used on ships, pipelines and underground storage tanks.

7. ERGONOMICS AND ANTHROPOMETRICS

Ergonomics: The science of designing products, systems and environments to suit the physical and psychological needs of users.

It aims to improve:

  • Comfort.

  • Safety.

  • Efficiency.

  • Usability.

  • Accessibility.

Anthropometrics: The measurement of the human body, including dimensions such as height, arm length, hand size and seated height.

Important anthropometric concepts

Static measurements: Measurements taken when the body is in a fixed position, e.g. seated height.

Dynamic measurements: Measurements taken while the body is moving, e.g. arm reach.

Percentiles: Statistical measurements showing the proportion of a population below a particular measurement.

  • 5th percentile: Smaller users; useful for reach and accessibility.

  • 50th percentile: Average measurement.

  • 95th percentile: Larger users; useful for clearance and space requirements.

Designing for a range of users:

  • Design for the smallest user when reach is important.

  • Design for the largest user when clearance or space is important.

  • Adjustable products can accommodate a wider range of users.

Examples:

  • Adjustable office chairs accommodate different leg lengths and sitting heights.

  • OXO Good Grips kitchen utensils use large, comfortable handles to improve grip and accessibility.

  • Adjustable car seats accommodate different driver heights.

Inclusive design: Designing products so that as many people as possible can use them, regardless of age, ability or physical characteristics.

8. HEALTH AND SAFETY – RISK ASSESSMENTS

A risk assessment identifies hazards and evaluates the likelihood and severity of harm so that appropriate control measures can be introduced.

Hazard: Something with the potential to cause harm.

Risk: The likelihood that harm will occur and how serious the consequences could be.

Five stages of a risk assessment

  1. Identify the hazards.

  2. Identify who may be harmed and how.

  3. Evaluate the risks and decide on control measures.

  4. Record the findings and implement the control measures.

  5. Review the assessment and update it when necessary.

Examples of workshop hazards

Hazard

Possible harm

Control measure

Rotating machinery

Entanglement

Guards, training and tied-back hair

Flying particles

Eye injuries

Safety goggles and machine guards

Wood dust

Respiratory problems

Extraction and suitable respiratory protection

Hot materials

Burns

Heat-resistant gloves and safe handling

Sharp tools

Cuts

Correct tool use and safe storage

Chemicals and adhesives

Skin or respiratory irritation

COSHH assessment and PPE

Trailing cables

Trips

Keep walkways clear

Important legislation

Health and Safety at Work etc. Act 1974

  • Main UK legislation establishing duties for employers and employees.

  • Employers must provide safe working environments, equipment, information and training.

  • Employees must follow safety procedures and take reasonable care.

COSHH – Control of Substances Hazardous to Health Regulations

  • Controls exposure to hazardous substances.

  • Employers assess chemical risks and introduce suitable controls.

  • Relevant to paints, solvents, resins, adhesives and dust.

PPE – Personal Protective Equipment

  • Equipment worn to reduce exposure to hazards.

  • Examples: safety goggles, ear defenders, gloves, dust masks and protective footwear.

  • PPE is not a substitute for safer systems of work or engineering controls.

9. THE SIX Rs OF SUSTAINABILITY

The six Rs are strategies designers use to reduce environmental impact and encourage sustainable product development.

Reduce

  • Minimise material, energy and resource consumption.

  • Example: lightweight packaging using less plastic.

Reuse

  • Use a product or component again rather than discarding it.

  • Example: reusable water bottles.

Recycle

  • Process waste materials into new materials or products.

  • Example: recycling aluminium drinks cans.

Rethink

  • Question how a product is designed, manufactured, used and disposed of.

  • Example: designing modular furniture that can be repaired and upgraded.

Refuse

  • Avoid unnecessary or environmentally damaging products and materials.

  • Example: refusing unnecessary single-use plastic packaging.

Repair

  • Fix damaged products rather than replacing them.

  • Example: replacing the battery in a phone instead of purchasing a new phone.

Why are they important?

  • Reduce landfill.

  • Conserve finite resources.

  • Reduce pollution and energy consumption.

  • Extend product life.

  • Encourage a circular economy.

10. FEASIBILITY STUDIES

A feasibility study investigates whether a proposed product or design idea is realistic and achievable before significant resources are committed.

Main areas of feasibility

Technical feasibility

  • Are the necessary materials, machinery and skills available?

  • Can the product actually be manufactured?

  • Can it meet the required performance standards?

Economic feasibility

  • Is the product affordable to develop and manufacture?

  • Will the selling price cover production costs?

  • Is there potential for profit?

Market feasibility

  • Is there customer demand?

  • Who is the target market?

  • Are there competing products?

Environmental feasibility

  • Can sustainable materials be used?

  • What is the environmental impact of manufacture and disposal?

Legal feasibility

  • Does the product comply with relevant legislation and safety standards?

  • Are there copyright, patent or intellectual property issues?

Time feasibility

  • Can the product be designed, tested and manufactured within the available timeframe?

Example: A company considering an electric bicycle must investigate battery costs, motor technology, safety regulations, market demand, manufacturing costs and environmental impact before investing.

11. DESIGN COMMUNICATION – 3D DRAWING TYPES

Design communication allows designers to communicate ideas, forms, dimensions and construction details to manufacturers and clients.

Isometric drawing

  • Shows three dimensions in one drawing.

  • Vertical lines remain vertical.

  • The two horizontal axes are drawn at 30 degrees to the horizontal.

  • Parallel edges remain parallel.

  • Useful for communicating the overall shape of a product.

Oblique drawing

  • Shows the front face in true shape.

  • Depth is represented by receding lines, usually at 45 degrees.

  • Can use a full or half depth scale.

  • Useful for displaying the front and depth of a product.

Perspective drawing

  • Represents objects as they appear to the human eye.

  • Parallel lines appear to converge towards vanishing points.

  • Can use one-point, two-point or three-point perspective.

  • Useful for realistic presentation drawings.

One-point perspective: Uses one vanishing point, often for interiors or products viewed straight on.

Two-point perspective: Uses two vanishing points, commonly for viewing the corner of a product.

Three-point perspective: Uses three vanishing points, useful for dramatic views from above or below.

Exploded isometric drawing

  • Shows individual components separated from one another.

  • Demonstrates how a product is assembled.

  • Useful for instruction manuals and manufacturing.

Orthographic projection

  • Uses separate 2D views, usually front, plan and side elevations.

  • Shows accurate dimensions and proportions.

  • Used for technical working drawings and manufacture.

12. QUALITY CONTROL

Quality control involves checking and testing products during and after manufacture to ensure they meet specified standards and tolerances.

Tolerance: The permitted variation from a specified measurement.

Example: If a component must measure 50 mm ±0.2 mm, acceptable measurements are 49.8–50.2 mm.

Quality control methods

  • Visual inspection – identifies surface defects, scratches and inconsistencies.

  • Measurement checks – checks dimensions against technical drawings.

  • Functional testing – checks whether the product performs correctly.

  • Material testing – checks strength, hardness and durability.

  • Sampling inspection – checks selected items from a production batch.

  • Go/no-go gauges – quickly check whether components fall within acceptable limits.

Quality control tools

Vernier callipers

  • Measure internal, external and depth dimensions.

  • More precise than an ordinary ruler.

  • Used to check component thickness and diameter.

Micrometers

  • Measure very small dimensions accurately.

  • Commonly used for checking material thickness and component diameters.

Go/no-go gauges

  • Go side should fit within the permitted size.

  • No-go side should not fit.

  • Quickly checks whether components meet tolerance requirements.

Laser scanning

  • Uses laser technology to capture dimensions and surface shapes.

  • Compares manufactured components with digital design models.

Probe measuring systems

  • Use a physical probe to measure specific points on a component.

  • Often used in coordinate measuring machines (CMMs).

X-ray testing

  • Non-destructive testing used to identify internal defects, cracks and voids.

Ultrasound testing

  • Uses high-frequency sound waves to detect internal flaws without damaging the product.

13. ECO-LABELLING

Eco-labels provide consumers with information about the environmental impact or sustainability characteristics of products.

Mobius Loop

  • Three chasing arrows forming a triangle.

  • Indicates that a product or packaging is recyclable.

  • Sometimes includes a percentage to show recycled content.

  • Recyclability depends on local collection and processing facilities.

European Eco-label (EU Ecolabel)

  • Flower-shaped label with an EU symbol.

  • Indicates products meet specified environmental performance criteria throughout relevant parts of their life cycle.

  • Found on products such as cleaning products, paper and textiles.

EC Energy Label

  • Provides information about the energy efficiency of appliances.

  • Uses an A–G scale, with A representing the highest efficiency and G the lowest under the current system.

  • Helps consumers compare energy consumption.

Energy Efficient label and logo

  • Identifies products that meet relevant energy-efficiency criteria.

  • Helps consumers identify products designed to use less energy.

FSC – Forest Stewardship Council

  • Indicates that wood or paper comes from responsibly managed forests or controlled sources, depending on the label.

  • Encourages sustainable forestry.

  • Used on furniture, packaging, paper and timber products.

ENERGY STAR

  • International energy-efficiency certification programme originating in the USA.

  • Identifies products that meet specific energy-efficiency standards.

  • Used on appliances, computers and other electrical equipment.




14. PAPER 1 MATHS SKILLSPercentage of waste

Percentage waste = (Waste material ÷ Total material used) × 100

Example:
A manufacturer uses 500 kg of material and wastes 40 kg.

(40 ÷ 500) × 100 = 8% waste

Calculating length of time

Time = Distance ÷ Speed

Example:
A machine produces 600 components at 30 components per minute.

600 ÷ 30 = 20 minutes

Remember to convert units when necessary.

Trigonometry

SOH CAH TOA:

  • sin θ = Opposite ÷ Hypotenuse

  • cos θ = Adjacent ÷ Hypotenuse

  • tan θ = Opposite ÷ Adjacent

Use when calculating unknown lengths or angles in right-angled triangles.

Perimeter

Perimeter = Total distance around the outside of a shape.

Rectangle: P = 2(length + width)

Triangle: P = a + b + c

Circle circumference: C = 2πr or πd

Frequency graphs

A frequency graph displays how often values occur.

  • Frequency = Number of times a value occurs.

  • Frequency table = Organises values into categories or intervals.

  • Frequency polygon = Points plotted at class midpoints and joined with straight lines.

  • Histogram = Displays grouped continuous data using adjoining bars.

Important: A histogram uses frequency density when class intervals have unequal widths.

Frequency density = Frequency ÷ Class width.