Comprehensive Internal Combustion Engines Study Guide

Overview of Heat Engines and Applications

  • Heat Engine Classifications:

    • Four-stroke petrol engine
    • Two-stroke petrol engine
    • Four-stroke Compression Ignition (C.I.) engine
    • Two-stroke Compression Ignition (C.I.) engine
    • Comparison between four-stroke and two-stroke engines
  • Applications of Four-Stroke Engines:

    • Motor cars
    • Motor bikes
    • Boats
    • Trucks
    • Lifting equipment
    • Water pumps
    • Generators
  • Principles of Multi-Cylinder Engine Analysis:

    • The operation of each cylinder in a multi-cylinder engine is identical.
    • Focusing on a single-cylinder engine provides a complete understanding of the operation of all four-stroke petrol engines.

Fundamental Engine Terminology and Principles

  • Top Dead Centre (t.d.c.):

    • Defined as the position of the piston at the end of its upward stroke.
    • Represents the absolute highest point that the piston can reach inside the cylinder.
  • Bottom Dead Centre (b.d.c.):

    • Defined as the position of the piston at the end of its downward stroke.
    • Represents the absolute lowest point that the piston can reach inside the cylinder.
  • Stroke:

    • The maximum linear distance of piston movement between extreme points (between t.d.c. and b.d.c.).
    • During one stroke, the crankshaft turns through an angle of 180×180^\times or 180o180^\text{o}.
    • The total stroke distance is double the crank throw distance.
  • Cycle:

    • The complete sequence of the four strokes of the piston.
    • One complete cycle is achieved during two crankshaft revolutions (720o720^\text{o}) and one camshaft revolution (360o360^\text{o}).

Operational Mechanics of the Four-Stroke Petrol Engine

  • The Intake Stroke:

    • The piston moves downward from t.d.c. toward b.d.c.
    • As the piston descends from t.d.c., the intake valve starts opening while the exhaust valve remains fully closed.
    • The downward motion creates a partial vacuum (depression) inside the cylinder space above the piston.
    • Atmospheric pressure fills this partial vacuum by forcing outside air through the carburettor barrel.
    • Inside the carburettor barrel, petrol is mixed with air.
    • This air-fuel mixture flows through the intake manifold and past the open intake valve into the cylinder.
    • Just after the piston reaches b.d.c., the intake valve closes.
  • The Compression Stroke:

    • Both the intake valve and the exhaust valve remain closed during the entire stroke.
    • The piston moves upward from b.d.c. to t.d.c.
    • The petrol-air mixture is compressed into the relatively small clearance volume of the combustion chamber.
    • Just before the piston reaches t.d.c., a high-tension spark is introduced into the combustion chamber via the spark plug, igniting the compressed petrol mixture.
  • The Power Stroke:

    • Both valves remain closed.
    • As a result of ignition, rapid combustion of the petrol mixture occurs.
    • Combustion generates high temperatures, causing the burned gases to expand rapidly.
    • This expansion exerts heavy pressure on the piston crown, transmitting force to the crankshaft via the connecting rod, converting linear motion into rotary motion.
  • The Exhaust Stroke:

    • As the piston reaches b.d.c., the exhaust valve opens.
    • Rotation of the crankshaft continues due to stored kinetic energy/momentum in the crankshaft, assisted by the flywheel.
    • The piston moves upward from b.d.c. to t.d.c., forcing burnt exhaust gases past the open exhaust valve into the exhaust manifold.
    • The gases are released into the atmosphere via exhaust piping.
    • Upon reaching t.d.c., the engine is positioned to begin the next intake stroke and repeat the cycle.

Environmental Considerations and Exhaust Emissions

  • Environmental Impact of Engine Emissions:

    • A running internal combustion engine emits exhaust gas containing carbon monoxide (CO\text{CO}).
    • Carbon monoxide is toxic and highly harmful to human health and the environment.
  • Emission Control Developments:

    • Leaded petrol has been phased out completely.
    • Modern vehicles are equipped with catalytic converters that convert harmful carbon monoxide (CO\text{CO}) into less harmful carbon dioxide (CO2\text{CO}_2).

Design and Operation of the Three-Port Two-Stroke Petrol Engine

  • Historical Background and Uses:

    • The two-stroke engine principle was invented by Sir Dugald Clerk in 1880.
    • Widely utilized in motorcycles, lawn mowers, and motorboats.
  • Structural Construction:

    • Features no poppet valves; instead, gas flow is governed by three ports: intake port, exhaust port, and transfer port.
    • Ports are uncovered and covered directly by the moving body/skirt of the piston.
    • Transfer Port: Has no direct connection to ambient air; connects the sealed crankcase directly to the cylinder area above the piston crown. Located on one side of the cylinder wall, opposite the intake and exhaust ports.
    • Sealed Crankcase: Functionally air-tight and contains no standing lubricating oil sump; engine oil is pre-mixed directly into the petrol fuel.
    • Scavenging Piston Crown: Specially shaped crown designed to deflect incoming fresh air-fuel charge upward to promote efficient scavenging.
    • Scavenging Definition: The process wherein incoming compressed fresh gases from the transfer port push burnt exhaust gases out through the exhaust port, purging the cylinder.
  • Two-Stroke Cycle Principles (360o360^\text{o} Crankshaft Cycle):

    • Cycle is completed in only two piston strokes and one single revolution (360o360^\text{o}) of the crankshaft.
    • Direct pumping action of the piston cannot be utilized as in a four-stroke engine; burnt gases are cleared primarily by incoming pressurized air-fuel mixture.
  • Two-Stroke Operational Sequence:

    • Intake and Compression Strokes (Piston travel from b.d.c. to t.d.c.):
    • At b.d.c., the intake port is closed while the transfer and exhaust ports are open, leaving the upper cylinder filled with petrol mixture.
    • As the piston travels upward, it covers the transfer port first and then covers the exhaust port.
    • Ascending motion compresses the petrol mixture in the combustion chamber above while simultaneously creating a vacuum in the crankcase below.
    • Further upward travel uncovers the intake port, causing fresh petrol mixture to enter the crankcase vacuum.
    • Just before reaching t.d.c., the compressed overhead air-fuel mixture is ignited by a high-tension spark.
    • Power and Exhaust Strokes (Piston travel from t.d.c. to b.d.c.):
    • Combustion generates high temperatures and expanding gases that force the piston downward toward b.d.c., imparting rotation to the crankshaft.
    • As the piston moves downward, it covers the intake port, compressing the fresh petrol mixture trapped inside the crankcase.
    • Continued downward movement uncovers the exhaust port first, allowing burnt exhaust gases to begin escaping.
    • Shortly thereafter, the transfer port is uncovered; the compressed petrol mixture in the crankcase enters the upper cylinder under pressure, sweeping out remaining exhaust gases.
  • Piston Crown Deflector Design:

    • Specially contoured to deflect incoming fresh air-fuel mixture upward away from the exhaust port.
    • Prevents the unburned fresh petrol mixture from escaping directly out through the open exhaust port with burnt gases, which would waste fuel and leave residual exhaust in the upper cylinder.

Comparison Between Two-Stroke and Four-Stroke Engines

  • Two-Stroke Engines:

    • Contains fewer moving parts.
    • Operates on two piston strokes per complete power cycle.
    • Requires one crankshaft revolution (360o360^\text{o}) per cycle.
    • Features a gas-tight, sealed crankcase.
    • Contains no standing lubricating oil in the crankcase; oil is mixed into petrol fuel for lubrication.
    • Spaces above and below the piston are pressurized for compression processes.
    • The piston body directly controls the flow of gases into and out of the cylinder ports.
    • Requires no camshaft.
  • Four-Stroke Engines:

    • Contains more moving parts.
    • Operates on four piston strokes per complete power cycle.
    • Requires two crankshaft revolutions (720o720^\text{o}) per cycle.
    • The crankcase is not gas-tight.
    • The crankcase contains an oil sump filled with engine oil for lubrication.
    • Gas is pressurized only on the top side of the piston.
    • Mechanical intake and exhaust valves control the flow of gases in the cylinder.
    • Requires a camshaft to control valve operation.

Detailed Component Analysis, Materials, and Functions

  • Cylinder Block:

    • Structural features include bored cylinder liners, holes for push rods, mounting pads for the water pump, welsh plugs, and mountings for main bearings.
    • Forms the main structural casing for single-cylinder or multi-cylinder (e.g., four-cylinder) configurations.
  • Cylinder Head:

    • Materials: Manufactured from cast iron or aluminium alloy.
    • Indirectly air-cooled / water-cooled design: Cast as a single unit containing internal water jackets.
    • Direct air-cooled design: Contains no internal water jackets; constructed with external cooling fins to increase surface area exposed to cooling airflow.
    • Functions:
    • Acts as a sealed lid for cylinders to permit full compression without pressure leakage.
    • Forms a major section of the combustion chamber volume.
    • Houses valve guides, valves, springs, and valve mechanisms in overhead valve (OHV) engines (in side-valve engines, valve mechanisms are located in the cylinder block).
    • Accommodates spark plugs, manifold studs, and thermostat mountings.
  • Crankshaft:

    • Materials: Steel alloys containing nickel-chrome and chrome-vanadium.
    • Mounting and structure: Main shaft housed in cylinder block main bearing liners; equipped with main journals, big-end bearing journals (crankpins), and internal oil channels. Contains as many crank journals as there are engine cylinders.
    • Function: Converts linear reciprocating motion of pistons into smooth rotary motion.
  • Piston:

    • Materials: Cast iron or aluminium alloy.
    • Structure: Hollow cylindrical unit closed at top (piston crown), fitted with a gudgeon pin bore and external circumferential grooves for piston rings.
    • Functions:
    • Functions as a pump element to create a vacuum during intake, compress the mixture during compression, and sweep out burned gases during exhaust.
    • Transmits expansion force from combustion gases to the crankshaft via gudgeon pin and connecting rod.
  • Piston Rings:

    • Materials: Cast iron; chrome plating added to top compression rings.
    • Application rates:
    • Average modern engines utilize 3 piston rings per piston.
    • Smaller engines utilize 2 piston rings per piston (never fewer than 2).
    • Two-stroke engines utilize compression rings only; no oil control rings applied.
    • Types and Functions:
    • Compression Rings: Mounted above gudgeon pin position closest to piston crown. Form a gas-tight seal between piston and cylinder wall to prevent high combustion pressure escaping into crankcase.
    • Oil Control Rings: Mounted below gudgeon pin position (when 3 rings are used, exactly 1 is an oil control ring). Controls oil film thickness on cylinder walls by scraping off excess oil while maintaining adequate surface lubrication.
  • Gudgeon Pin:

    • Materials: High-grade steel alloy, case-hardened.
    • Structure and Installation: Hollow cylinder passing through piston pin bosses and small-end bearing of connecting rod.
    • Mounting variations:
    • Fixed installation: Pressed or clamped into connecting rod small-end (bearing surface is within piston bosses).
    • Floating installation: Loose fit in small-end, secured in place by spring circlips fitted in piston bosses.
    • Function: Functions as crank and slider linkage connecting piston to connecting rod.
  • Connecting Rod:

    • Materials: High-grade cast steel alloyed with chrome-vanadium.
    • Components: Small-end, main shank, big-end, shell bearings, and big-end cap.
    • Function: Connects piston to crankshaft to transfer linear power stroke forces.
  • Camshaft:

    • Materials: Alloy composed of cast iron, copper, and chrome.
    • Structural details: Features ground pear-shaped cams, bearing journals, and gear drive attachments.
    • Functions:
    • Converts rotary motion of crankshaft into reciprocating motion of engine valves.
    • Opens valves at pre-determined precise timing intervals.
    • Drives distributor shaft, oil pump, and mechanical fuel pump.
  • Timing Drive Systems:

    • Timing Gears:
    • Composed of crankshaft gear and camshaft gear located at front of engine.
    • Camshaft gear contains exactly twice the number of teeth of crankshaft gear (2:12:1 ratio) to drive camshaft at half crankshaft speed.
    • Direct meshing drives camshaft in opposite rotational direction to crankshaft.
    • Timing Chains:
    • Applied when camshaft and crankshaft gears cannot mesh directly.
    • Transmits rotary motion in same rotational direction.
    • Subject to wear and chain stretching causing noise; managed by applying chain tensioners.
    • Timing Belts:
    • Toothed timing belts running on toothed pulleys, used in most modern vehicles for precise valve timing.
    • Advantages: Requires no lubrication and operates quieter than gears or chains.
    • Maintenance requirement: Requires periodic replacement to avoid belt failure and resulting severe engine damage.
  • Valve Lifters (Tappets):

    • Materials: Steel alloys, case-hardened.
    • Function: Rides directly on pear-shaped cam lobes of camshaft to generate reciprocating motion.
    • Types and Applications:
    • Adjustable Valve Lifter: Positioned directly between camshaft and valve stem on side-valve engines and specific overhead camshaft engines; incorporates valve clearance adjustment.
    • Non-Adjustable Lifters: Includes tubular, mushroom, roller, and hydraulic lifters placed between camshaft and pushrod on overhead valve (OHV) engines.
  • Spark Plugs:

    • Function: Provides an isolated air gap inside combustion chamber across which high-voltage ignition spark jumps to ignite air-fuel charge at end of compression stroke.
  • Ignition Distributor:

    • Construction Materials:
    • Distributor sleeve: Aluminium alloy
    • Driving shaft with cams: Steel alloy
    • Contact-breaker plate: Soft steel
    • Contact breaking points: Tungsten
    • Rotor arm: Synthetic material
    • Distributor cover/cap: Synthetic material
    • Major Assembly Parts: Distributor cap, vacuum advance mechanism, distributor shaft.
    • Function: Routes high-voltage spark pulses from ignition coil to individual spark plugs in correct firing order and precise timing.
  • Engine Auxiliary Systems:

    • Starter Motor: Electric motor that rotates crankshaft at pre-determined speed to initiate intake and compression sequence required to start engine.
    • Alternator: Generates electricity to power vehicle electronics and maintain battery charge while engine runs. (Must not be used to charge a completely flat battery).
    • Bearings:
    • Materials: Shells made of bronze or brass with thin surface lining of white metal or lead-antimony-radium alloy; rolling element ball bearings used in select auxiliary components.
    • Function: Reduces friction on rotating journals (e.g., main bearings, gudgeon pin bushings, camshaft bearings).
    • Fuel Pump:
    • Function: Supplies fuel from storage tank to carburettor at pre-determined pressure across all engine operating speeds.
    • Mechanical fuel pumps: Driven by camshaft rotation.
    • Electrical fuel pumps: Applied on modern fuel-injected vehicles.
    • Water Pump:
    • Location: Mounted at front of engine between block and radiator.
    • Function: Continuously circulates liquid coolant through engine block water jackets and radiator to ensure uniform coolant temperature and prevent thermal failure around combustion chambers and cylinders.