(08/27) Lecture Circuit Analysis: Sources, Resistors, Ohm's Law, Series Proof, and Voltage Division

Course Announcements and Administrative Items

  • Homework Assignments:

    • Homework 0 must be actively worked on, completed, and submitted.

  • Quizzes:

    • There is a required quiz that must be taken and completed.

Independent and Dependent Sources

  • Source Classifications:

    • Circuit elements include both independent sources and dependent sources.

    • Four dependent source configurations are introduced, bringing the total number of fundamental source types to 77.

  • Active Element Power Convention:

    • All 77 source types are classified as active elements.

    • Relative to the passive sign convention, active elements deliver current such that current leaves the positive terminal (the terminal of higher potential).

    • When current leaves the higher potential terminal, the calculated power delivered/generated is:

p=−v×ip = -v \times i

Resistors, Resistance, and Conductance

  • Resistor Symbol and Sign Convention:

    • The standard schematic diagram symbol for a resistor consists of a series of zigzag lines with terminals extending from each end.

    • Under the reference diagram relative to the passive sign convention, current flows from higher potential (++) to lower potential (−-).

    • Because current enters the positive terminal, a resistor is strictly a passive element.

    • Resistors always and exclusively dissipate electrical power and voltage.

  • Resistance (RR):

    • The base SI unit for resistance is the Ohm, named after Georg Simon Ohm.

    • The symbol for the Ohm is the capital Greek letter Omega (Ω\Omega).

    • The circuit variable for resistance is capital RR. (Lowercase rr is reserved to denote radius).

  • Conductance (GG):

    • Conductance (GG) is defined as the reciprocal or mathematical inverse of resistance:

G=1RG = \frac{1}{R}

  • Units of Conductance:

    1. Mho:

      • Derived by spelling Ohm backwards.

      • Symbolized by an inverted capital Greek letter Omega (℧\mho).

    2. Siemens:

      • The modern SI unit for conductance, symbolized by capital S\text{S}.

      • Named after the German surname Siemens (where the initial 'S' is pronounced with a 'Z' sound).

      • Mhos and Siemens are identical in magnitude and fully interchangeable (1 ℧=1 S1\,\mho = 1\,\text{S}).

Ohm's Law and Power Equations

  • Ohm's Law:

    • When a potential difference (voltage) exists across a completed resistor circuit, the resulting current ii flowing through the resistor is directly proportional to the voltage vv:

v∝iv \propto i

*   Graphing voltage vv as a function of current ii produces a straight line passing through the origin.
*   The constant of proportionality (the slope of the V-IV\text{-}I line) is the resistance RR.
*   **Ohm's Law Formula**:

v=i×Rv = i \times R

  • Power Dissipation Formulas for Resistors:

    • Fundamental power relation:

p=i×vp = i \times v

*   **First Alternative Power Formula** (substituting v=i×Rv = i \times R into p=i×vp = i \times v):

p=i×(i×R)=i2×Rp = i \times (i \times R) = i^2 \times R

*   **Second Alternative Power Formula** (rearranging Ohm's law to i=vRi = \frac{v}{R} and substituting into p=i×vp = i \times v):

p=(vR)×v=v2Rp = \left(\frac{v}{R}\right) \times v = \frac{v^2}{R}

*   Summary of power calculations for passive resistors:

p=i×v=i2×R=v2Rp = i \times v = i^2 \times R = \frac{v^2}{R}

Mathematical Proof: Equivalent Resistance of Resistors in Series

  • Resistor Connection Types:

    • Resistors can be connected in three ways: series, parallel, or neither.

    • Proofs for equivalent standard connections occur in four distinct pairs throughout the course.

  • Series Connection Characteristics:

    • A node connection is defined as a series connection if exactly two circuit elements connect at that node.

    • For a network of nn resistors (R1,R2,…,RnR_1, R_2, \dots, R_n) in series, two physical conditions hold implicitly:

      1. The current ii passing through every individual resistor is identical.

      2. The total voltage vv divides proportionally across each component into individual voltage drops (v1,v2,…,vnv_1, v_2, \dots, v_n).

  • Proof Constraints:

    • To prove equivalence between an nn-resistor series network and a single equivalent resistor ReqR_{eq}:

      • Constraint 1: Total voltage vv must be identical in both circuit representations.

      • Constraint 2: Total current ii must be identical in both circuit representations.

  • Formal Proof Steps:

    1. Apply the Law of Conservation of Energy by summing individual voltage drops to equal total voltage vv:

v=v1+v2+⋯+vnv = v_1 + v_2 + \dots + v_n

        For the equivalent single-resistor circuit:

v=veqv = v_{eq}

2.  Apply Ohm's Law substitutions (vk=i×Rkv_k = i \times R_k) to every component voltage term:

v=(i×R1)+(i×R2)+⋯+(i×Rn)v = (i \times R_1) + (i \times R_2) + \dots + (i \times R_n)

        For the equivalent circuit:

v=i×Reqv = i \times R_{eq}

3.  Factor out the common current variable ii from the series summation:

v=i×(R1+R2+⋯+Rn)v = i \times (R_1 + R_2 + \dots + R_n)

4.  Divide both expressions by the total current ii:

vi=R1+R2+⋯+Rn\frac{v}{i} = R_1 + R_2 + \dots + R_n

vi=Req\frac{v}{i} = R_{eq}

5.  By the transitive property (exploiting Constraints 1 and 2 where vi\frac{v}{i} is identical in both systems), equate the resistance terms:

Req=R1+R2+⋯+Rn=∑k=1nRkR_{eq} = R_1 + R_2 + \dots + R_n = \sum_{k=1}^{n} R_k

6.  Conclude the formal mathematical proof with **QED**:
    *   **QED** stands for *quod erat demonstrandum* ("that which was to be shown").
    *   QED is the required standard termination mark for all academic circuit proofs and carries explicit unit/credit value on examinations.

Voltage Division

  • Definition and Utility:

    • Voltage division is the first of three dedicated analysis shortcuts ("tricks") taught in the course.

    • It consolidates three individual calculations into a single equation to determine the voltage across any specific resistor in a series chain when total voltage vv is known.

  • Comparison of Computational Approaches:

    • Standard Three-Calculation Procedure:

      1. Sum series resistors to find equivalent resistance: Req=Ra+Rb+Rc+⋯+RnR_{eq} = R_a + R_b + R_c + \dots + R_n

      2. Calculate total loop current: i=vReqi = \frac{v}{R_{eq}}

      3. Calculate voltage drop across target resistor RaR_a using Ohm's Law: va=i×Rav_a = i \times R_a

    • Single-Calculation Voltage Division Formula:

va=v×RaRa+Rb+Rc+⋯+Rnv_a = v \times \frac{R_a}{R_a + R_b + R_c + \dots + R_n}

  • Anatomy of the Formula:

    • The denominator (Ra+Rb+Rc+⋯+Rn)(R_a + R_b + R_c + \dots + R_n) executes Step 1 (ReqR_{eq}).

    • The term vdenominator\frac{v}{\text{denominator}} executes Step 2 (ii).

    • Multiplying by numerator RaR_a executes Step 3 (vav_a).

  • Scope of Application:

    • Voltage division applies universally to any arbitrary number of resistors connected in series, ranging from 22 to ∞\infty.