Basic Sciences (Physics) - Units & Measurements and Measurement Techniques
Institutional Overview and Course Assessment Scheme
Institution Details:
Shirpur Education Society (SES)
R. C. Patel College of Engineering and Polytechnic, Shirpur
Department of Applied Sciences
Institutional Motto: ॥ सा विद्या या विमुक्तये ॥
Course Name: Basic Sciences (Physics)
Course Code:
Semester: FY - 1K
Subject Teacher: Mr. Swapnil. S. Tayade
Subject Breakdown:
Basic Sciences () comprises two main disciplines: Basic Physics and Basic Chemistry.
**Theory Examination Scheme (
Formative Assessment Theory (FA TH) / Internal Examination:
Includes Test 1 () and Test 2 ().
Calculated as the average of Test 1 and Test 2: .
FA TH Total = .
Summative Assessment Theory (SA TH) / End Semester Examination:
Online Mode Examination consisting of Multiple Choice Questions (MCQ).
Duration: .
SA TH Total = .
Total Theory Marks: .
**Practical Examination Scheme (
Formative Assessment Practical (FA PR):
FA PR Physics =
FA PR Chemistry =
FA PR Total = .
Summative Assessment Practical (SA PR):
SA PR Physics =
SA PR Chemistry =
SA PR Total = .
Total Practical Marks: .
Self-Learning Assessment (S.L.A / SLA):
SLA Physics () + SLA Chemistry () = .
Total SLA Marks = .
Topic I: Units & Measurements (Fundamentals and Standard Requirements)
Topic Specification:
Weightage: ()
Teaching Hours: ()
Definition of Physics:
Physics is defined as the branch of Science that deals with nature and natural phenomena.
In physics, the properties of matter are studied along with the laws governing these properties.
The different quantities used for the study of physics are called physical quantities.
Physics is fundamentally based on measurements.
Need for Measurement in Engineering and Sciences:
The measurement of a given quantity is defined as the act or result of a quantitative comparison between an unknown quantity and a defined standard quantity.
Measurement plays an essential role in daily life as well as in all branches of Engineering and Sciences.
Two main requirements of measurements:
The standard used for comparison purposes must be accurately defined and commonly accepted.
The apparatus used and procedure developed must be provable.
Requirements of Standard Units:
It should be universally accepted.
It should be definite and well-defined.
It should be invariable with time and place.
It should be easily comparable with other similar units.
It should be easily reproducible.
It should be readily available.
Systems of Units and Classification of Physical Quantities
Fundamental Base Quantities:
Length, Mass, and Time are taken as basic physical quantities. Many other physical quantities can be generated using these base quantities.
Systems of Units in Use:
C.G.S System: A Gaussian system of units with centimeter (), gram (), and second () as fundamental units for length, mass, and time, respectively. These units are very small.
M.K.S System: A metric system of units with meter (), kilogram (), and second () as fundamental units for length, mass, and time, respectively. It is a metric system because multiples and submultiples are related to practical units by powers of .
F.P.S System (British System): A system of units with Foot, Pound, and Second as fundamental units for length, mass, and time, respectively. This system is not in wide use because conversion from F.P.S to any other system is difficult.
S.I. System: An abbreviation of the French name Système International. This system consists of seven fundamental units with the help of which other units can be generated.
Derived Physical Quantities and Units:
Area: Unit = Square meter, Symbol =
Density: Unit = kilogram/meter, Symbol =
Volume: Unit = Cubic meter, Symbol =
Velocity: Unit = meter/sec, Symbol =
Acceleration: Unit = meter/sec, Symbol =
Force: Unit = Newton, Symbol =
Thermal Conductivity: Unit = watt/, Symbol =
Viscosity: Unit = N.sec/meter, Symbol =
Angular Velocity: Unit = radian/sec, Symbol =
Frequency: Unit = Hertz, Symbol =
Supplementary Physical Quantities and Units:
Plane Angle: Unit = Radian, Symbol =
Solid Angle: Unit = Steradian, Symbol =
Scalars and Vectors
Scalar Quantity:
Defined as a physical quantity that has only magnitude.
Represented by a number and a unit.
Does not possess any direction.
Examples: Length, Mass, Time, Temperature, Distance, Speed, Area, Volume, Density, Charge, Electric Current, Potential Difference, Resistance, Work, Power, Energy.
Vector Quantity:
Defined as a physical quantity that has both magnitude and direction.
Represented by its magnitude (number and unit) and its direction.
Examples: Force (), Acceleration (), Weight, Pressure (), Momentum, Gravity, Electric Field (), Magnetic Field, Impulse, Torque, Gravitational Field, Magnetic Flux.
Comparison Between Scalar and Vector Quantities:
1. Magnitude & Direction: Scalar has magnitude only; Vector has both magnitude and direction.
2. Direction: Scalar does not have direction; Vector has direction.
3. Specification: Scalar is specified by a number (magnitude) and a unit; Vector is specified by a number (magnitude), direction, and unit.
4. Change Conditions: Scalar changes with a change in its magnitude; Vector changes with a change in its magnitude, its direction, or both.
5. Algebraic Rules: Scalar follows ordinary rules of algebra; Vector follows rules of vector algebra.
6. Symbolic Examples: Scalar: , , , etc.; Vector: , , , etc.
Dimensions and Dimensional Equations
Dimensions of Physical Quantities:
The dimensions of a physical quantity are the powers to which fundamental quantities are raised when representing that physical quantity as a product of base quantities.
Standard Symbols for Base Quantities:
Length is expressed by
Mass is expressed by
Time is expressed by
Temperature is expressed by
Current is expressed by
Luminous Intensity is expressed by
Amount of Substance is expressed by
Dimensional Formula (Equation):
An equation that gives the relation between fundamental units and derived units in terms of dimensions is called a dimensional formula.
In mechanics, Length, Mass, and Time are taken as 3 base dimensional representations: , , and .
The derived unit of all physical quantities can be represented in terms of the base units raised to specific powers.
Examples of Dimensional Derivations:
Area:
Momentum:
Force:
Pressure:
Errors in Measurements and Mathematical Estimation
Definition of Error:
An error is a fault that may occur even in the most careful observation.
Arises due to human limitations and instrumental limitations.
Cannot be completely eliminated, but can be reduced.
Main Types of Errors:
Instrumental / Constant Error:
Occurs due to the use of faulty instruments or calibration errors.
Example: Using a voltmeter having a zero-scale calibration error introduces a constant error whenever it is used.
Reduction: Reduced by taking measurements with different instruments.
Systematic Error:
Defined as constant, repeatable deviations from the true value in a single direction.
Random Error:
Caused due to changes in experimental conditions that are out of control.
Cannot be completely eliminated.
Personal Error:
Occurs due to inaccuracies caused by the observer's habits, personal limitations, or lack of skill.
Estimation of Error:
Minimizing and properly estimating errors allows for eliminating discrepancies to achieve better accuracy and precision in measurement.
Calibration of instruments is enabled by proper estimation of errors.
Error Formulation and Calculations:
Mean / Average Value ( or ):
Absolute Error ():
Difference between average (corrected) reading and individual reading.
Mean Absolute Error ():
The arithmetic mean of absolute values of individual absolute errors.
Relative Error:
Ratio of average absolute error to average value.
Percentage Error:
Relative error expressed as a percentage.
Significant Figures and Rounding Off Rules
Significant Figures & Digits:
Significant figures are figures in any place in numbers that are reasonably trustworthy (meaningful).
Significant digits are digits meaningful in assigning a true or realistic value to the result.
Rules to Determine Significant Figures:
1. The digits (all non-zero digits) are significant.
2. Zero is significant only if it comes in between two non-zero numbers (e.g., has significant figures).
3. All zeros to the right side of the decimal point and left side of non-zero digits are NOT significant (e.g., has significant figures; zeros are used only to fix the decimal point).
4. Zero is significant if it is to the right side of a non-zero digit after a decimal point (e.g., has significant digits; has significant digits).
5. If zero is on the right side of a non-zero digit without decimals, it may or may not be significant (e.g., has significant figures: ; leading zeros are not significant).
In numbers like , all digits are significant, including the zero (total significant figures).
6. In addition or subtraction, the least decimal place among the operated values must be retained in the final result.
7. In multiplication and division, the result should be expressed with the least number of significant figures as associated with the least precise number in the operation.
Rounding Off Approximate Numbers:
Definition: The process of omitting insignificant digits and retaining only the desired number of significant digits, including required modifications to the last retained significant digit.
Purpose: During calculations, reducing numbers introduces accepted errors up to a certain extent.
Process: While rounding to a certain place value, all digits to the right of that place value are dropped.
Rounding Rules:
Rounding Down: If the first dropped digit is
Rounding Up: If the first dropped digit is
Examples of Rounding to 2 Decimal Places:
(First dropped digit is
(First dropped digit is
(First dropped digit is
Practical Applications of Measuring Instruments
Applications of Vernier Caliper:
Used to measure distances between objects, internal and external dimensions, including height.
Resolution: Measures accurately up to a tenth part of a millimeter ().
Sector Applications:
Education Sector: Measures materials undergoing temperature changes; measures regular and irregular objects.
Science Laboratory: Measures apparatus in science labs for error-free calculations.
Medical Apparatus: Measures tools used in surgical and medical applications.
Aerospace Sector: Measures minute details in aerial parts to prevent aviation accidents.
Internal Measurement: Inner jaws measure interior dimensions such as pipe inner diameters.
Mechanical Parts: Measures shaft diameters, keyway dimensions, and shaft lengths.
Containers: Measures the depth and length of bottles or beakers.
Applications of Screw Gauges (Micrometer Screw Gauge):
Measuring Diameter: Measures the diameter and radius of circular objects, primarily wires, with an accuracy of .
Measuring Thickness: Measures the thickness of glass slabs, metal sheets, or paper. Uniform thickness of any shape can be determined.
Measuring Volume: Measures the diameter of a given lead sheet or lead shot to determine its volume.
Ancient Astronomical Instruments
Historical Background:
Lalla was an 8th-century Indian astronomer, astrologer, and mathematician who lived in central India (possibly modern south Gujarat).
Types of Ancient Instruments:
Gola Yantra: A type of armillary sphere used to locate planetary positions.
Bhangana: A ring with angular graduations along its circumference; acts as a type of protractor.
Chakra: A circular disk with angular graduations; acts as a type of protractor.
Dhanus: A semicircular disk with angular graduations provided with a stick at the center; a type of protractor with a plumb bob.
Yasti Yantra (Yesti Yantra):
"Yasti" means stick, giving it the name "stick machine".
Designed by Bhaskaracharya.
Operating Procedure and Construction:
1. Consists of a board on which a long stick is pivoted, allowing upward and downward movement of the rod.
2. The board is mounted at a certain height from the ground.
3. The observer focuses on the top of the object by moving the stick upward. The line of sight is defined by the stick's direction, and its position is marked on the board.
4. The stick is then moved downward while focusing on the bottom of the object.
5. The new stick position is marked on the board.
6. A line parallel to ground level is drawn on the board through the pivot point.
7. Reference lines and perpendiculars are drawn on the reference line from specific points on the line of sight, forming two triangles.
8. The height of the tall object is determined based on the proportions of the two triangles formed.
Phalaka Yantra:
Consists of a board provided with a pin and an index arm.
Used to determine time graphically by observing the Sun's position and altitude.
Course Assignment Questions
Q1: Define unit. State it with examples.
Q2: Define physical quantity. State its types.
Q3: Define fundamental physical quantity. State its examples with unit.
Q4: Define derived physical quantity. State its examples with unit.
Q5: Define supplementary quantity. State its examples with units.
Q6: State the requirement of standard units.
Q7: Define Scalar & vector quantity. State their examples.
Q8: Define:
a) Dimension of physical quantity.
b) State symbol used to represent dimensional formula.
c) Define dimensional formula. State any two examples.
Q9: State application of dimensional analysis.
Q10: Define error. State types of error.
Q11: State the steps of how to reduce errors.
Q12: Define:
a) Relative error.
b) Percentage error with formulae.
c) Significant figures.
Q13: State the rules to determine significant figures.
Q14: State:
i) Chakra yantra
ii) Yasti yantra
iii) Dhanu yantra
iv) Phalaka yantra
Q15: State applications of:
a) Vernier caliper
b) Micrometer screw gauge