Electromagnetic Waves: Comprehensive Theory, Equations, and Spectrum

Unification of Electromagnetism and Historical Foundations

  • Foundations of Electromagnetism:

    • An electric current produces a magnetic field around it, and two current-carrying wires exert a magnetic force on one another.
    • Faraday's Law of Induction demonstrates that a magnetic field changing with time gives rise to an electric field.
    • A time-varying electric field generates a magnetic field, providing symmetry between electricity and magnetism.
  • Contributions of James Clerk Maxwell (1831–1879):

    • Born in Edinburgh, Scotland, Maxwell derived the thermal velocity distribution of molecules in a gas and obtained reliable estimates of molecular parameters (such as viscosity) from measurable quantities.
    • Maxwell unified the independent laws of electricity and magnetism (discovered by Coulomb, Oersted, Ampere, and Faraday) into a consistent set of coupled differential equations known as Maxwell's equations.
    • By applying these equations, Maxwell predicted the existence of electromagnetic waves, formed by coupled time-varying electric and magnetic fields propagating through space.
    • The predicted speed of propagation in a vacuum was found to be approximately 3×108 m/s3 \times 10^8\,\text{m/s}, matching optical measurements for the speed of light, leading to the fundamental conclusion that light is an electromagnetic wave.
    • Maxwell disagreed with the hypothesis that electricity was particulate in nature, despite evidence suggested by Faraday's laws of electrolysis.
  • Experimental Verification and Early Wireless Communication:

    • Heinrich Rudolf Hertz (1857–1894): In 1887, Hertz experimentally demonstrated the existence of electromagnetic waves in the low-frequency radio wave region. He produced EM waves, transmitted them through space, and measured their wavelength and speed. He proved that their reflection, refraction, and vibration properties were identical to light and heat waves. Hertz also pioneered research on electrical discharge through gases and discovered the photoelectric effect.
    • Jagdish Chandra Bose: Working in Calcutta (Kolkata) seven years after Hertz, Bose generated and observed short-wavelength electromagnetic waves ranging from 25 mm25\,\text{mm} to 5 mm5\,\text{mm} in laboratory conditions.
    • Guglielmo Marconi: Transmitted electromagnetic waves over distances of several kilometers in Italy, launching the field of modern wireless communications.

The Displacement Current and Maxwell-Ampere Law

  • Inconsistency in Ampere's Circuital Law:
    • Ampere's original circuital law states that the line integral of the magnetic field B\mathbf{B} around any closed loop is proportional to the total conduction current i(t)i(t) passing through a surface bounded by the loop:

∮B⋅dl=μ0i(t)\oint \mathbf{B} \cdot d\mathbf{l} = \mu_0 i(t)

*   Consider a parallel plate capacitor CC connected to a circuit carrying a time-varying charging current i(t)i(t).

A parallel plate capacitor charging with different surfaces

*   **Surface 1 (Flat Circular Surface)**: A circular loop of radius rr is placed outside the capacitor plates centered around the current-carrying wire. By symmetry, the magnetic field BB is tangential along the perimeter:

B(2πr)=μ0i(t)B(2\pi r) = \mu_0 i(t)

*   **Surface 2 (Pot-Shaped or Tiffin-Box Surface)**: A surface sharing the exact same circular rim rr extends inside the gap between the capacitor plates without touching the conducting wire or plates.
*   Since no conduction current flows through the vacuum gap between the plates, the right-hand side of Ampere's law evaluates to zero:

∮B⋅dl=0\oint \mathbf{B} \cdot d\mathbf{l} = 0

*   This creates a logical contradiction: the magnetic field BB at a specific point PP outside the plates evaluates to a non-zero value using Surface 1, but evaluates to zero using Surface 2.
  • Derivation of Maxwell's Displacement Current:
    • The electric field E\mathbf{E} between capacitor plates of area AA with total time-dependent charge Q(t)Q(t) is uniform and perpendicular to the plates:

E=Qε0AE = \frac{Q}{\varepsilon_0 A}

*   The total electric flux ΦE\Phi_E passing through the surface SS between the plates is:

ΦE=EA=(Qε0A)A=Qε0\Phi_E = E A = \left(\frac{Q}{\varepsilon_0 A}\right) A = \frac{Q}{\varepsilon_0}

*   Taking the time derivative of both sides relates the changing flux to the current i=dQdti = \frac{dQ}{dt}:

dΦEdt=1ε0dQdt=iε0\frac{d\Phi_E}{dt} = \frac{1}{\varepsilon_0} \frac{dQ}{dt} = \frac{i}{\varepsilon_0}

*   Rearranging gives the missing current term required to maintain consistency across all surfaces, termed the **displacement current** (idi_d):

id=ε0dΦEdti_d = \varepsilon_0 \frac{d\Phi_E}{dt}

  • Total Current and Generalised Ampere-Maxwell Law:
    • The total effective current ii is the sum of the conduction current ici_c (due to actual flow of electric charges) and the displacement current idi_d (due to time-varying electric fields):

i=ic+id=ic+ε0dΦEdti = i_c + i_d = i_c + \varepsilon_0 \frac{d\Phi_E}{dt}

*   **Outside the plates**: Conduction current exists (ic=ii_c = i), and displacement current is zero (id=0i_d = 0).
*   **Inside the plates**: Conduction current is zero (ic=0i_c = 0), and displacement current exists (id=ii_d = i).
*   The generalised **Ampere-Maxwell Law** is expressed as:

∮B⋅dl=μ0ic+μ0ε0dΦEdt\oint \mathbf{B} \cdot d\mathbf{l} = \mu_0 i_c + \mu_0 \varepsilon_0 \frac{d\Phi_E}{dt}

  • Physical Significance and Consequences:
    • Displacement current produces magnetic fields in the exact same manner as conduction current.
    • In a charging capacitor, magnetic fields generated inside the plates (e.g., at point MM) match those generated just outside the plates (e.g., at point PP).
    • Displacement current completes the symmetrical foundation of electromagnetism:
      • Faraday's Law: A time-varying magnetic field induces an electric field.
      • Ampere-Maxwell Law: A time-varying electric field induces a magnetic field.

Maxwell's Equations in Vacuum

  • Maxwell's equations, combined with the Lorentz force formula F=q(E+v×B)\mathbf{F} = q(\mathbf{E} + \mathbf{v} \times \mathbf{B}), mathematically express all classical electrodynamic phenomena.

  • 1. Gauss's Law for Electricity:

∮E⋅dA=Qε0\oint \mathbf{E} \cdot d\mathbf{A} = \frac{Q}{\varepsilon_0}

*   *Physical meaning*: Electric flux through any closed surface equals the total enclosed charge divided by permittivity.
  • 2. Gauss's Law for Magnetism:

∮B⋅dA=0\oint \mathbf{B} \cdot d\mathbf{A} = 0

*   *Physical meaning*: Net magnetic flux through any closed surface is always zero; isolated magnetic monopoles do not exist.
  • 3. Faraday's Law of Electromagnetic Induction:

∮E⋅dl=−dΦBdt\oint \mathbf{E} \cdot d\mathbf{l} = -\frac{d\Phi_B}{dt}

*   *Physical meaning*: Line integral of electric field around a closed loop equals the negative rate of change of magnetic flux.
  • 4. Ampere-Maxwell Law:

∮B⋅dl=μ0ic+μ0ε0dΦEdt\oint \mathbf{B} \cdot d\mathbf{l} = \mu_0 i_c + \mu_0 \varepsilon_0 \frac{d\Phi_E}{dt}

*   *Physical meaning*: Line integral of magnetic field around a closed loop is produced by both conduction current and changing electric flux.

Physical Properties and Nature of Electromagnetic Waves

  • Sources of Electromagnetic Waves:

    • Stationary charges produce only static electrostatic fields.
    • Charges moving with uniform velocity (steady currents) produce constant magnetic fields that do not change with time.
    • Accelerated charges radiate electromagnetic waves. An oscillating charge produces an oscillating electric field in space, which induces an oscillating magnetic field, continuously regenerating each other as a propagating wave.
    • The frequency of the emitted EM wave is identical to the frequency of oscillation of the source charge.
    • The energy carried by the wave originates from the mechanical/electrical energy of the accelerating source charge.
  • Transverse Wave Propagation:

    • Electric and magnetic fields in an EM wave are mutually perpendicular to each other and perpendicular to the direction of propagation vector k\mathbf{k}.

Linearly polarised electromagnetic wave

*   For a plane wave traveling along the positive zz\text{-axis}:

Ex(z,t)=E0sin⁡(kz−ωt)E_x(z, t) = E_0 \sin(k z - \omega t)

By(z,t)=B0sin⁡(kz−ωt)B_y(z, t) = B_0 \sin(k z - \omega t)

*   **Wave Vector Magnitude** (kk):

k=2πλk = \frac{2\pi}{\lambda}

*   **Angular Frequency** (ω\omega):

ω=2πν\omega = 2\pi \nu

  • Wave Speed and Field Amplitude Relations:
    • Speed of wave propagation in vacuum (cc):

c=ωk=1μ0ε0c = \frac{\omega}{k} = \frac{1}{\sqrt{\mu_0 \varepsilon_0}}

*   Relationship between frequency ν\nu, wavelength λ\lambda, and speed cc:

νλ=c\nu \lambda = c

*   Ratio of electric field amplitude E0E_0 to magnetic field amplitude B0B_0 at any point:

E0B0=corB0=E0c\frac{E_0}{B_0} = c \quad \text{or} \quad B_0 = \frac{E_0}{c}

*   Speed of EM waves in a linear material medium with permittivity ε\varepsilon and permeability μ\mu:

v=1μεv = \frac{1}{\sqrt{\mu \varepsilon}}

*   The speed of EM waves in vacuum is independent of wavelength and acts as an absolute constant used to define the international standard of length (meter).
*   EM waves carry energy and momentum from one point to another without requiring a physical material medium.

Worked Examples

  • Example 8.1:
    • Problem: A plane EM wave of frequency 25 MHz25\,\text{MHz} travels in free space along the xx\text{-direction}. At a specific point in space and time, E=6.3j^ V/m\mathbf{E} = 6.3\mathbf{\hat{j}}\,\text{V/m}. Calculate B\mathbf{B} at this point.
    • Solution:
      • Calculate magnitude using B=EcB = \frac{E}{c}:

B=6.3 V/m3×108 m/s=2.1×10−8 TB = \frac{6.3\,\text{V/m}}{3 \times 10^8\,\text{m/s}} = 2.1 \times 10^{-8}\,\text{T}

    *   Determine direction using vector cross-product E×B\mathbf{E} \times \mathbf{B} pointing in direction of propagation (+x+x\text{-axis}, i^\mathbf{\hat{i}}).
    *   Since E\mathbf{E} points in the +y+y\text{-direction} (j^\mathbf{\hat{j}}), j^×k^=i^\mathbf{\hat{j}} \times \mathbf{\hat{k}} = \mathbf{\hat{i}}. Thus, B\mathbf{B} points along the +z+z\text{-direction} (k^\mathbf{\hat{k}}):

B=2.1×10−8k^ T\mathbf{B} = 2.1 \times 10^{-8}\mathbf{\hat{k}}\,\text{T}

  • Example 8.2:
    • Problem: The magnetic field in a plane EM wave is given by By=(2×10−7 T)sin⁡(0.5×103x+1.5×1011t)B_y = (2 \times 10^{-7}\,\text{T}) \sin(0.5 \times 10^3 x + 1.5 \times 10^{11} t).
      • (a) Determine the wavelength λ\lambda and frequency ν\nu.
      • (b) Write an expression for the electric field E\mathbf{E}.
    • Solution:
      • Compare given wave equation with standard form By=B0sin⁡[2π(xλ+tT)]B_y = B_0 \sin\left[2\pi \left(\frac{x}{\lambda} + \frac{t}{T}\right)\right]:

k=2πλ=0.5×103 m−1  ⟹  λ=2π0.5×103 m−1=1.26×10−2 m=1.26 cmk = \frac{2\pi}{\lambda} = 0.5 \times 10^3\,\text{m}^{-1} \implies \lambda = \frac{2\pi}{0.5 \times 10^3\,\text{m}^{-1}} = 1.26 \times 10^{-2}\,\text{m} = 1.26\,\text{cm}

ω=2πν=1.5×1011 rad/s  ⟹  ν=1.5×10112π=23.9×109 Hz=23.9 GHz\omega = 2\pi \nu = 1.5 \times 10^{11}\,\text{rad/s} \implies \nu = \frac{1.5 \times 10^{11}}{2\pi} = 23.9 \times 10^9\,\text{Hz} = 23.9\,\text{GHz}

    *   Calculate electric field amplitude E0E_0:

E0=B0c=(2×10−7 T)×(3×108 m/s)=60 V/mE_0 = B_0 c = (2 \times 10^{-7}\,\text{T}) \times (3 \times 10^8\,\text{m/s}) = 60\,\text{V/m}

    *   Direction of propagation is along −x-x\text{-axis} (due to ++ sign between spatial and temporal terms). Field B\mathbf{B} is along yy\text{-axis}. Thus, E\mathbf{E} must oscillate along the zz\text{-axis}:

Ez=60sin⁡(0.5×103x+1.5×1011t) V/mE_z = 60 \sin(0.5 \times 10^3 x + 1.5 \times 10^{11} t)\,\text{V/m}

The Electromagnetic Spectrum

  • The electromagnetic spectrum covers an infinite range of frequencies without sharp boundary divisions. Regions are designated based on production and detection methods.

Electromagnetic Spectrum Diagram

  • 1. Radio Waves:

    • Wavelength Range: >0.1 m> 0.1\,\text{m}
    • Frequency Range: 500 kHz500\,\text{kHz} to 1000 MHz1000\,\text{MHz}
    • Sub-bands:
      • AM (Amplitude Modulated): 530 kHz530\,\text{kHz} to 1710 kHz1710\,\text{kHz}
      • Short Wave Bands: Up to 54 MHz54\,\text{MHz}
      • TV Waves: 54 MHz54\,\text{MHz} to 890 MHz890\,\text{MHz}
      • FM (Frequency Modulated) Radio: 88 MHz88\,\text{MHz} to 108 MHz108\,\text{MHz}
      • Cellular Phones: Ultrahigh frequency (UHF) band
    • Production: Rapid acceleration and deceleration of electrons in conducting aerials.
    • Detection: Receiver aerials.
  • 2. Microwaves:

    • Wavelength Range: 0.1 m0.1\,\text{m} to 1 mm1\,\text{mm}
    • Production: Special vacuum tubes such as klystron valves, magnetron valves, or Gunn diodes.
    • Detection: Point contact diodes.
    • Applications:
      • Radar systems used in aircraft navigation.
      • Speed guns used by law enforcement to time vehicles and sports balls.
      • Microwave ovens: Frequency is matched to the resonant frequency of water molecules (≈2.45 GHz\approx 2.45\,\text{GHz}), efficiently transferring energy to molecular kinetic energy, raising food temperature.
  • 3. Infrared Waves:

    • Wavelength Range: 1 mm1\,\text{mm} to 700 nm700\,\text{nm}
    • Production: Vibration of atoms and molecules; emitted by hot bodies.
    • Detection: Thermopiles, bolometers, infrared photographic film.
    • Applications and Features:
      • Often called "heat waves" because water, CO2\text{CO}_2, and NH3\text{NH}_3 molecules absorb them, increasing internal molecular thermal motion.
      • Infrared lamps used in physical therapy.
      • Greenhouse effect: Earth absorbs visible solar radiation and re-radiates it as longer-wavelength infrared rays, which are trapped by greenhouse gases (CO2\text{CO}_2, water vapor) to preserve planetary warmth.
      • Infrared detectors on Earth satellites monitor military activities and crop growth.
      • LED infrared emitters used in electronic remote controls for TVs and hi-fi systems.
  • 4. Visible Light:

    • Wavelength Range: 700 nm700\,\text{nm} to 400 nm400\,\text{nm}
    • Frequency Range: 4×1014 Hz4 \times 10^{14}\,\text{Hz} to 7×1014 Hz7 \times 10^{14}\,\text{Hz}
    • Spectral Colors and Wavelengths:
      • Red: 700 nm700\,\text{nm} to 650 nm650\,\text{nm}
      • Orange: 650 nm650\,\text{nm} to 600 nm600\,\text{nm}
      • Yellow: 600 nm600\,\text{nm} to 550 nm550\,\text{nm}
      • Green: 550 nm550\,\text{nm} to 500 nm500\,\text{nm}
      • Blue: 500 nm500\,\text{nm} to 450 nm450\,\text{nm}
      • Violet: 450 nm450\,\text{nm} to 400 nm400\,\text{nm}
    • Production: Atomic electron transitions from higher to lower energy levels.
    • Detection: Human eye, photocells, photographic film.
    • Biological Variation: Snakes detect infrared radiation; many insects can see into the ultraviolet spectrum.
  • 5. Ultraviolet Rays (UV):

    • Wavelength Range: 400 nm400\,\text{nm} to 1 nm1\,\text{nm} (4×10−7 m4 \times 10^{-7}\,\text{m} to 6×10−10 m6 \times 10^{-10}\,\text{m})
    • Production: Special lamps, electric welding arcs, very hot bodies like the Sun.
    • Detection: Photocells, photographic film.
    • Applications and Protection:
      • Ozone layer (40–50 km40\text{--}50\,\text{km} altitude) absorbs most solar UV; depletion by chlorofluorocarbons (CFCs like freon) poses environmental hazards.
      • Excessive exposure causes melanin production (skin tanning) and sunburns.
      • Ordinary glass absorbs UV radiation, preventing sunburn through window glass.
      • Welding face shields feature special glass to shield eyes from high UV levels.
      • Used in LASIK eye surgery due to high focusability into narrow beams.
      • UV germicidal lamps used in water purifiers.
  • 6. X-rays:

    • Wavelength Range: 1 nm1\,\text{nm} to 10−3 nm10^{-3}\,\text{nm} (10−8 m10^{-8}\,\text{m} to 10−13 m10^{-13}\,\text{m})
    • Production: High-energy electron bombardment of heavy metal targets in X-ray tubes; inner shell electron transitions.
    • Detection: Photographic film, Geiger tubes, ionization chambers.
    • Applications: Medical diagnostic imaging, radiation therapy for cancer treatment. Requires shielding due to tissue damage risks.
  • 7. Gamma Rays:

    • Wavelength Range: <10−3 nm< 10^{-3}\,\text{nm} (10−10 m10^{-10}\,\text{m} to <10−14 m< 10^{-14}\,\text{m})
    • Production: Nuclear reactions and radioactive decay of atomic nuclei.
    • Detection: Photographic film, Geiger tubes, ionization chambers.
    • Applications: Medical oncology to destroy cancer cells.

Summary Table of EM Wave Spectrum

  • Overview of Spectrum Types, Ranges, Production, and Detection:
TypeWavelength RangeProduction MethodDetection Method
Radio>0.1 m> 0.1\,\text{m}Rapid acceleration/deceleration of electrons in aerialsReceiver's aerials
Microwave0.1 m0.1\,\text{m} to 1 mm1\,\text{mm}Klystron valve or magnetron valvePoint contact diodes
Infra-red1 mm1\,\text{mm} to 700 nm700\,\text{nm}Vibration of atoms and moleculesThermopiles, Bolometer, Infrared photographic film
Light700 nm700\,\text{nm} to 400 nm400\,\text{nm}Electrons in atoms moving to lower energy levelsThe eye, Photocells, Photographic film
Ultraviolet400 nm400\,\text{nm} to 1 nm1\,\text{nm}Inner shell atomic electron transitionsPhotocells, Photographic film
X-rays1 nm1\,\text{nm} to 10−3 nm10^{-3}\,\text{nm}X-ray tubes or inner shell electronsPhotographic film, Geiger tubes, Ionization chamber
Gamma rays<10−3 nm< 10^{-3}\,\text{nm}Radioactive decay of the nucleusPhotographic film, Geiger tubes, Ionization chamber

Key Technical Insights and Ponder Points

  • Fundamental Distinction: All EM waves travel through vacuum at speed c=3×108 m/sc = 3 \times 10^8\,\text{m/s}; differences in behavior arise entirely from varying wavelengths and frequencies, altering their interaction modes with matter.
  • Scale Correlation: The wavelength emitted by a radiating system correlates with the physical size of the source structure:
    • Gamma Rays (10−1410^{-14} to 10−15 m10^{-15}\,\text{m}): Originate from subatomic nuclei.
    • X-rays: Emitted from electron transitions in heavy individual atoms.
    • Radio Waves: Generated by macroscopic circuits; aerial antennas radiate most efficiently when physical antenna dimensions match the wave's wavelength (L≈λL \approx \lambda).
  • Thermal Effects of Infrared: Infrared radiation vibrates whole molecular structures (unlike visible light which excites atomic electrons), increasing molecular kinetic energy and temperature.
  • Evolutionary Adaptation: Human visual sensitivity peaks at the middle of the optical spectrum (≈550 nm\approx 550\,\text{nm}), matching the peak emission wavelength of solar radiation.

End-of-Chapter Exercises

  • Exercise 8.1:

    • Problem: A capacitor consists of two circular plates of radius R=12 cmR = 12\,\text{cm} separated by d=5.0 cmd = 5.0\,\text{cm}, charged by a constant current i=0.15 Ai = 0.15\,\text{A}.
      • (a) Calculate capacitance CC and rate of change of potential difference dVdt\frac{dV}{dt}.
      • (b) Obtain displacement current idi_d.
      • (c) Verify if Kirchhoff's junction rule applies at each plate.
    • Solutions/Key Relations:
      • Capacitance C=ε0Ad=ε0πR2dC = \frac{\varepsilon_0 A}{d} = \frac{\varepsilon_0 \pi R^2}{d}.
      • Since q=CVq = C V, dqdt=i=CdVdt  ⟹  dVdt=iC\frac{dq}{dt} = i = C \frac{dV}{dt} \implies \frac{dV}{dt} = \frac{i}{C}.
      • Displacement current id=ε0dΦEdt=i=0.15 Ai_d = \varepsilon_0 \frac{d\Phi_E}{dt} = i = 0.15\,\text{A}.
      • Kirchhoff's first rule holds because incoming conduction current equals outgoing displacement current (ic=idi_c = i_d).
  • Exercise 8.2:

    • Problem: Circular parallel plate capacitor with R=6.0 cmR = 6.0\,\text{cm}, C=100 pFC = 100\,\text{pF} connected to Vrms=230 VV_{\text{rms}} = 230\,\text{V} AC at ω=300 rad/s\omega = 300\,\text{rad/s}.
      • (a) Calculate irmsi_{\text{rms}}.
      • (b) Is ic=idi_c = i_d?
      • (c) Calculate magnetic field amplitude B0B_0 at r=3.0 cmr = 3.0\,\text{cm} from axis.
    • Solutions/Key Relations:
      • Capacitive reactance Xc=1ωCX_c = \frac{1}{\omega C}; i_{\text{rms}} = \frac{V_{\text{rms}}}{X_c} = V_{\text{rms}} \omega C$.\n * i_c = i_d holds true instantaneously and for rms values.\n * Magnetic field inside plates at radius r \le RisisB_0 = \frac{\mu_0 r}{2\pi R^2} i_0$, where i0=2irmsi_0 = \sqrt{2} i_{\text{rms}}.
  • Exercise 8.3:

    • Question: What physical quantity is identical for X-rays (λ=10−10 m\lambda = 10^{-10}\,\text{m}), red light (λ=6800 A˚\lambda = 6800\,\text{\AA}), and radio waves (λ=500 m\lambda = 500\,\text{m})?
    • Answer: Speed in vacuum (c=3×108 m/sc = 3 \times 10^8\,\text{m/s}).
  • Exercise 8.4:

    • Problem: EM wave travels along zz\text{-direction} in vacuum. Determine vector orientations and calculate λ\lambda for ν=30 MHz\nu = 30\,\text{MHz}.
    • Solution: E\mathbf{E} and B\mathbf{B} lie in x-yx\text{-}y plane mutually perpendicular. Wavelength λ=cν=3×108 m/s30×106 Hz=10 m\lambda = \frac{c}{\nu} = \frac{3 \times 10^8\,\text{m/s}}{30 \times 10^6\,\text{Hz}} = 10\,\text{m}.
  • Exercise 8.5:

    • Problem: Radio tuning range 7.5 MHz7.5\,\text{MHz} to 12 MHz12\,\text{MHz}. Find corresponding λ\lambda band.
    • Solution: λ1=3×1087.5×106=40 m\lambda_1 = \frac{3 \times 10^8}{7.5 \times 10^6} = 40\,\text{m}; λ2=3×10812×106=25 m\lambda_2 = \frac{3 \times 10^8}{12 \times 10^6} = 25\,\text{m}. Band is 25 m25\,\text{m} to 40 m40\,\text{m}.
  • Exercise 8.6:

    • Problem: Particle oscillates at ν=109 Hz\nu = 10^9\,\text{Hz}. Find frequency of radiated EM waves.
    • Solution: ν=109 Hz\nu = 10^9\,\text{Hz}.
  • Exercise 8.7:

    • Problem: Magnetic field amplitude B0=510 nTB_0 = 510\,\text{nT}. Calculate electric field amplitude E_0$.\n * *Solution*: E_0 = c B_0 = (3 \times 10^8\,\text{m/s}) \times (510 \times 10^{-9}\,\text{T}) = 153\,\text{V/m}.\n\n* **Exercise 8.8**:\n * *Problem*: Electric field amplitude E_0 = 120\,\text{N/C},frequency, frequency u = 50.0\,\text{MHz}.\n * (a) Calculate B_0,,\omega,,k,and, and\lambda.\n * (b) Write expressions for \mathbf{E}andand\mathbf{B}.\n * *Solutions*:\n * B_0 = \frac{E_0}{c} = \frac{120}{3 \times 10^8} = 400\,\text{nT}.\n * \omega = 2\pi u = 2\pi (50 \times 10^6) = 3.14 \times 10^8\,\text{rad/s}.\n * \lambda = \frac{c}{ u} = \frac{3 \times 10^8}{50 \times 10^6} = 6.0\,\text{m}.\n * k = \frac{2\pi}{\lambda} = \frac{2\pi}{6} = 1.05\,\text{rad/m}.\n\n* **Exercise 8.9**:\n * *Problem*: Using photon quantum energy E = h u,calculatephotonenergiesacrossspectralbandsinelectron−volts(, calculate photon energies across spectral bands in electron-volts (\text{eV}).\n * *Key Conversion*: 1\,\text{eV} = 1.6 \times 10^{-19}\,\text{J};;h = 6.63 \times 10^{-34}\,\text{J}\cdot\text{s}.\n\n* **Exercise 8.10**:\n * *Problem*: Plane wave electric field frequency u = 2.0 \times 10^{10}\,\text{Hz},amplitude, amplitudeE_0 = 48\,\text{V/m}.\n * (a) Calculate wavelength \lambda = \frac{3 \times 10^8}{2 \times 10^{10}} = 1.5\,\text{cm}.\n * (b) Calculate B_0 = \frac{48}{3 \times 10^8} = 1.6 \times 10^{-7}\,\text{T}.\n * (c) Show average energy densities match: u_E = \frac{1}{4} \varepsilon_0 E_0^2andandu_B = \frac{B_0^2}{4\mu_0}.Substituting. SubstitutingE_0 = c B_0andandc^2 = \frac{1}{\mu_0 \varepsilon_0}provesprovesu_E = u_B$$.