DC Circuit Analysis: Quantities, Dividers, Measurement, Batteries, and Power Transfer
Fundamental Electrical Quantities, Notation, and Conventions
Electrical quantities are real scalar values (not vectors) and can assume positive or negative signs.
Variable naming and symbol conventions:
Lowercase symbols (e.g., , , ) denote quantities that vary with time.
Uppercase symbols (e.g., , , ) denote quantities that are constant over time.
Standard Electrical Quantities, Units, and Symbols:
Charge: Symbol , Unit coulomb, Unit Symbol
Current: Symbol , Unit ampere, Unit Symbol
Voltage: Symbol , Unit volt, Unit Symbol
Energy: Symbol , Unit joule, Unit Symbol
Power: Symbol , Unit watt, Unit Symbol
Resistance: Symbol , Unit ohm, Unit Symbol
Capacitance: Symbol , Unit farad, Unit Symbol
Inductance: Symbol , Unit henry, Unit Symbol
Frequency: Symbol , Unit hertz, Unit Symbol
Torque: Symbol , Unit newton-metre, Unit Symbol
Angular velocity: Symbol , Unit radian per second, Unit Symbol
Rotational speed: Symbol , Unit revolutions per minute, Unit Symbol
Standard Engineering SI Prefixes:
atto ():
femto ():
pico ():
nano ():
micro ():
milli ():
kilo ():
mega ():
giga ():
tera ():
Significant Figures and Rounding Rules:
Standard precision in electrical circuit analysis requires or significant figures due to measurement equipment limitations.
Identification of significant figures:
Leading zeros are never significant (e.g., has s.f.; has s.f.).
Intermediate zeros between non-zero digits are significant (e.g., has s.f.).
Trailing zeros to the left of an unwritten decimal point are not significant unless explicitly specified (e.g., has s.f.; has s.f.).
Trailing zeros to the right of a decimal point are significant (e.g., has s.f.).
Systematic procedure to round a calculated result to significant figures:
Identify the leftmost non-zero digit.
Retain that digit and the subsequent digits.
Examine the 5th digit: if it is or greater, round the 4th digit up.
If the rounded rightmost digit is a zero, explicitly state the significance level (e.g., ).
Resistor Fundamentals, Color Coding, and Measurement
Fluid Analogy of Electrical Resistance:
Electrical current () corresponds to the rate of air volume flowing through a straw.
Electrical voltage () corresponds to the blowing pressure applied to force air through the straw.
Electrical resistance () corresponds to pinching the straw; pinching tighter increases resistance, demanding higher pressure to sustain air flow.
Unit definition: Resistance is measured in ohms (), where .

Resistor Color Code System:
Band colors represent significant digits, decimal multipliers, tolerances, temperature coefficients, and failure rates:
Black: Digit , Multiplier , Temp. Coeff.
Brown: Digit , Multiplier , Tolerance , Temp. Coeff. , Fail Rate
Red: Digit , Multiplier $xA\times 1002\%\,\text{(G)}50\,\text{ppm/K (R)}0.1\%\n - Orange: Digit 3\times 1\,\text{k}15\,\text{ppm/K (P)}0.01\%\n - Yellow: Digit 4\times 10\,\text{k}25\,\text{ppm/K (Q)}0.001\%\n - Green: Digit 5\times 100\,\text{k}0.5\%\,\text{(D)}20\,\text{ppm/K (Z)}\n - Blue: Digit 6\times 1\,\text{M}0.25\%\,\text{(C)}10\,\text{ppm/K (Z)}\n - Violet: Digit 7\times 10\,\text{M}0.1\%\,\text{(B)}5\,\text{ppm/K (M)}\n - Grey: Digit 8\times 100\,\text{M}0.05\%\,\text{(A)}1\,\text{ppm/K (K)}\n - White: Digit 9\times 1\,\text{G}\n - Gold: Multiplier \times 0.15\%\,\text{(J)}\n - Silver: Multiplier \times 0.0110\%\,\text{(K)}\n - None: Tolerance 20\%\,\text{(M)}\n - Reading Direction: Indicated by a wider physical gap separating band 3 and band 4 (or preceding the tolerance band).\n - Band decoding example: A 4-band resistor with bands Yellow, Purple, Orange, Gold:\n - Band 1 (Yellow) = 4\n - Band 2 (Purple) = 7\n - Band 3 (Orange) = \times 10^3\n - Band 4 (Gold) = \pm 5\%\n - Nominal value: 47 \times 10^3\,\Omega = 47\,\text{k}\Omega \pm 5\%\n\n- Multimeter Operation for Resistance and Continuity:\n - Resistance Measurement:\n - Measuring range selected dictates display units (e.g., 2\,\text{k}\Omega20\,\text{k}\Omega200\,\text{k}\Omega\text{k}\Omega2\,\text{M}\Omega\text{M}\Omega).\n - Shorted probes (touched together) on the lowest resistance range (e.g., 200\,\Omega0.00\,\Omega.\n - Probes held apart indicate an open circuit (displaying overload `1` or `OL`).\n - Human skin resistance measured across probe tips on the highest range (2\,\text{M}\Omega) typically requires slightly moist skin to register a reading.\n - Continuity and Diode Test Mode:\n - Selected via the diode/audible icon mode.\n - Audio buzzer sounds continuously when probe tips are connected across a low-resistance path.\n - Mandatory safety rule: Continuity tests must strictly be conducted on completely unpowered circuits to avoid meter damage or erroneous readings.\n\n# Breadboard Architecture and Circuit Prototyping\n\n\n\n- Internal Hardware Mechanics:\n - Contains spring-loaded metallic strips beneath the plastic shell to bridge specific hole groups.\n - Bus Rails (Power Strips): Horizontal rows running along the top and bottom edges are internally connected end-to-end horizontally.\n - Terminal Strips (Component Area): Central vertical columns are internally connected across groups of 5 holes (labeled A–E and F–J).\n - Isolation Center Divider: A central trench isolates column section A–E from section F–J, allowing integrated circuit (IC) placement across the center.\n\n- Continuity Verification across Breadboard Locations:\n - Point A to Point E (separate power rail rows): No continuity (no beep).\n - Point A to Point F (same power rail row): Full continuity (beep).\n - Point A to Point B (power rail row vs terminal strip column pin): No continuity (no beep).\n - Point B to Point C (same vertical column segment of 5 connected holes): Full continuity (beep).\n - Point C to Point D (opposite sides of central isolation trench): No continuity (no beep).\n\n\n\n- Light-Emitting Diode (LED) Circuit Assembly and Component Polarity:\n - LED Polar Terminals:\n - Anode (Positive): Round side of plastic casing, longer terminal lead.\n - Cathode (Negative): Flat edge of plastic casing, shorter terminal lead.\n - Circuit Topography: A 9\,\text{V}470\,\Omega current-limiting resistor and an LED.\n - Peer Review Method: Engineering practice requiring team members to verify schematic wiring drawings prior to applying power.\n - Power Storage Safety: Disconnect the 9\,\text{V} battery clip when storing equipment to prevent accidental short circuits across metallic tools.\n\n\n\n- DC Voltage Measurement Methodology:\n - Voltmeter connection rule: Always place probes in parallel (across) the component or sub-circuit being measured.\n - Probe Polarity: Red probe connects to the relatively positive potential (+-, ground/COM).\n - Reversing probe polarity yields an identical voltage magnitude with a negative sign.\n\n# Voltage and Current Divider Laws\n\n- Voltage Divider Rule:\n - Function: Short-cut equation to calculate the voltage drop across one resistor in a series chain without evaluating loop current explicitly.\n - Strict Condition: Resistors must be strictly connected in series, carrying identical current (I).\n - Formulations for two series resistors (R_1R_2V):\n V_1 = V \frac{R_1}{R_1 + R_2}\n V_2 = V \frac{R_2}{R_1 + R_2}\n - Proportionality: The fraction of total voltage appearing across a resistor is directly proportional to its fractional resistance.\n\n- Mathematical Derivation of Voltage Divider:\n 1. Apply Kirchhoff's Voltage Law (KVL) around series loop:\n V = V_1 + V_2\n 2. Apply Ohm's Law to each component:\n V_1 = I R_1\n V_2 = I R_2\n 3. Combine step 1 and step 2 to express total current (I):\n V = I R_1 + I R_2 = I(R_1 + R_2) \implies I = \frac{V}{R_1 + R_2}\n 4. Substitute expression for IV_1:\n V_1 = \left(\frac{V}{R_1 + R_2}\right) R_1 = V \frac{R_1}{R_1 + R_2}\n\n- Current Divider Rule:\n - Function: Short-cut equation to determine current entering one parallel branch from a total entering current (I).\n - Strict Condition: Resistors must be strictly in parallel, sharing an identical terminal voltage (V).\n - Formulations for two parallel resistors (R_1R_2):\n I_1 = I \frac{R_1^{-1}}{R_1^{-1} + R_2^{-1}} = I \frac{R_2}{R_1 + R_2}\n I_2 = I \frac{R_2^{-1}}{R_1^{-1} + R_2^{-1}} = I \frac{R_1}{R_1 + R_2}\n - Conductance Relationship: Branch current division is directly proportional to individual branch conductance (G = R^{-1}).\n\n- Mathematical Derivation of Current Divider:\n 1. Express branch voltages using Ohm's Law:\n V = I_1 R_1 = I_2 R_2 \implies I_2 = I_1 \frac{R_1}{R_2}\n 2. Apply Kirchhoff's Current Law (KCL) at the top node:\n I = I_1 + I_2\n 3. Substitute I_2 into KCL equation:\n I = I_1 + I_1 \frac{R_1}{R_2} = I_1 \left(1 + \frac{R_1}{R_2}\right) = I_1 \left(\frac{R_1 + R_2}{R_2}\right)\n 4. Rearrange to solve for I_1:\n I_1 = I \frac{R_2}{R_1 + R_2} = I \frac{R_1^{-1}}{R_1^{-1} + R_2^{-1}}\n\n- Worked Example Problems:\n - Series Voltage Divider:\n - Parameters: V = 3.0\,\text{V}R_1 = 3.3\,\text{k}\Omega = 3300\,\OmegaR_2 = 7.7\,\text{k}\Omega = 7700\,\Omega.\n - Calculation:\n V_2 = V \frac{R_2}{R_1 + R_2} = 3.0 \times \frac{7700}{3300 + 7700} = 3.0 \times \frac{7700}{11000} = 2.1\,\text{V}\n - Parallel Current Divider:\n - Parameters: I = 350\,\text{mA} = 0.35\,\text{A}R_1 = 3.3\,\text{k}\Omega = 3300\,\OmegaR_2 = 7.7\,\text{k}\Omega = 7700\,\Omega.\n - Calculation:\n I_2 = I \frac{R_2^{-1}}{R_1^{-1} + R_2^{-1}} = 0.35 \times \frac{7700^{-1}}{3300^{-1} + 7700^{-1}} = 0.35 \times \frac{3300}{3300 + 7700} = 0.105\,\text{A} = 105\,\text{mA}\n\n# Battery Modeling, Energy Storage, and Non-Idealities\n\n- Battery Physical Characteristics:\n - Chemical energy storage cells exhibit distinct terminal voltage behavior under current loading.\n - Non-ideal behavior: Terminal voltage drops as output current increases.\n\n- Charge Storage Capacity:\n - Stored charge capacity is quantified in ampere-hours (\text{A}\cdot\text{h}).\n - Conversion to standard SI Coulombs (\text{C}):\n 1\,\text{A}\cdot\text{h} = (1\,\text{C}\cdot\text{s}^{-1}) \times (1\,\text{h}) \times (3600\,\text{s/h}) = 3600\,\text{C}\n - Discharge rate examples for a 1\,\text{A}\cdot\text{h} battery:\n - Supplies 1\,\text{A}1.0\,\text{hour}\n - Supplies 2\,\text{A}0.5\,\text{hours}\n - Supplies 0.1\,\text{A}10.0\,\text{hours}\n\n- Stored Energy Calculations:\n - Energy (WQV):\n W = Q V\n - Example 1: 6\,\text{V}2\,\text{A}\cdot\text{h} battery:\n W = 6\,\text{V} \times 2\,\text{A}\cdot\text{h} = (6\,\text{J/C}) \times (2\,\text{C/s}) \times (3600\,\text{s}) = 43200\,\text{J}\n - Example 2: 1.5\,\text{V}0.5\,\text{A}\cdot\text{h} battery:\n W = 1.5\,\text{V} \times 0.5\,\text{A}\cdot\text{h} = (1.5\,\text{J/C}) \times (0.5\,\text{C/s}) \times (3600\,\text{s}) = 2700\,\text{J}\n\n- Internal Resistance (R_S) Circuit Model:\n - A real battery is modeled as an ideal voltage source (V_SR_S).\n - Terminal voltage (V_tIR_L):\n V_t = V_S - I R_S = V_S \frac{R_L}{R_S + R_L}\n - Physical trend: Larger physical batteries exhibit smaller internal resistances (R_S), causing smaller voltage drops under high load currents.\n - Example calculation: Battery with V_S = 1.5\,\text{V}R_S = 3\,\OmegaR_L = 20\,\Omega:\n V_t = 1.5 \times \frac{20}{20 + 3} = 1.30\,\text{V}\n\n- Parameter Measurement Procedures:\n - Measuring Source Voltage (V_S):\n - Measure battery open-circuit terminal voltage using a high-impedance multimeter (I = 0).\n - Proof: When I = 0V_i = I R_S = 0\,\text{V}V_S = V_t + V_i = V_t.\n - Measuring Internal Resistance (R_S):\n - Connect a known fixed load resistor (R_LV_t).\n - Express R_S by rearranging the voltage divider:\n V_t = V_S \frac{R_L}{R_S + R_L} \implies R_S = R_L \frac{V_S - V_t}{V_t}\n\n# Power Transfer and Efficiency Optimization\n\n- Energy Loss and System Efficiency:\n - Efficiency (\eta) ratio formula:\n \eta = \frac{P_{out}}{P_{in}} = \frac{V_L I}{V_S I} = \frac{V_L}{V_S} = \frac{R_L}{R_S + R_L}\n - In efficiency terms, power loss across internal or line resistance R_SI^2 R_S.\n - Maximizing Efficiency: Requires minimizing source resistance (R_SR_L).\n\n\n\n- Maximum Power Transfer Theorem:\n - Load power dissipation equation:\n P_L = V_L I = I^2 R_L = \left(\frac{V_S}{R_S + R_L}\right)^2 R_L\n - Finding peak power: Differentiate P_LR_L\frac{d P_L}{d R_L} = 0).\n - Resulting Condition: Load resistance must equal internal source resistance (R_L = R_S). This state is defined as load matching.\n - Maximum load power delivered at match:\n P_{L,max} = \frac{V_S^2}{4 R_S}\n - Efficiency at Maximum Power Transfer:\n \eta = \frac{R_S}{R_S + R_S} = 0.50 = 50\%\n - Engineering Tradeoff: Matching load for maximum power transfer inherently wastes 50\% of input energy inside the source resistance.\n\n\n\n- High-Voltage Direct Current (HVDC) Transmission Case Study:\n - System Specifications: Voltage source V_S = 10\,\text{kV} = 10000\,\text{V}R_S = 30\,\OmegaR_L\n - Part a: Load resistance for maximum power transfer:\n R_L = R_S = 30\,\Omega\n - Part b: Maximum power delivered to load:\n P_L = \frac{V_S^2}{4 R_S} = \frac{(10000)^2}{4 \times 30} = \frac{10^8}{120} = 833.33\,\text{kW} \approx 833\,\text{kW}\n - Part c: Total power output supplied by source at peak transfer:\n P_{total} = \frac{V_S^2}{R_S + R_L} = \frac{(10000)^2}{30 + 30} = 1.667\,\text{MW} \approx 1.67\,\text{MW}\n - Part d: Minimum R_L\ge 90\% system efficiency:\n \eta = \frac{R_L}{R_S + R_L} \ge 0.90 \implies R_L \ge 0.90 R_S + 0.90 R_L \implies 0.10 R_L \ge 0.90 R_S\n R_L \ge 9 R_S = 9 \times 30\,\Omega = 270\,\Omega\n - Part e: Line current supplied at 90\%R_L = 270\,\Omega):\n I = \frac{V_S}{R_S + R_L} = \frac{10000}{30 + 270} = \frac{10000}{300} = 33.33\,\text{A} \approx 33.3\,\text{A}\n - Part f: Power delivered to load at 90\% efficiency:\n P_L = I^2 R_L = (33.33)^2 \times 270 = 300000\,\text{W} = 300\,\text{kW}\n\n# Solar-Powered Path Light Design Case Study\n\n- Design Requirements and Constraints:\n - Light source: High-brightness LED requiring continuous current I_{LED} = 30\,\text{mA}.\n - Operational hours: Summer night operational time = 8\,\text{hours/day}14\,\text{hours/day}.\n - Solar panel supply: Maximum charging current I_{solar} = 50\,\text{mA}.\n - Minimum required operating battery voltage > 3.2\,\text{V}.\n\n- Parameter Calculations and Engineering Decisions:\n - Part a: Minimum battery capacity calculation (must meet worst-case winter requirement):\n \text{Capacity}{min} = I{LED} \times t_{winter} = 30\,\text{mA} \times 14\,\text{h} = 420\,\text{mA}\cdot\text{h} = 0.420\,\text{A}\cdot\text{h}\n - Part b: Engineering justification for selecting larger practical battery capacities:\n - Chemical capacity degradation over extended charge/discharge cycling.\n - Protection against multiple consecutive cloudy or overcast winter days.\n - Preventing deep battery discharge states, which degrade cell lifespan.\n - Sub-zero ambient winter temperatures reducing effective electrochemical output capacity.\n - Part c: Rechargeable Battery Selection:\n - Battery choice: Lithium-Ion (Li-ion) rechargeable button/cylindrical cell (e.g., LIR2450 at 3.6\,\text{V}> 3.2\,\text{V} output cost-effectively.\n - Part d: Full depletion recharge time under maximum solar output current:\n t_{recharge} = \frac{\text{Capacity}}{I_{solar}} = \frac{420\,\text{mA}\cdot\text{h}}{50\,\text{mA}} = 8.4\,\text{hours}\n\n# Circuit Analysis Theory Problems and Solutions\n\n- Problem 1: Incandescent Light Globe Network Analysis\n - Part a: Single globe connected across 3\,\text{V}0.2\,\text{A}:\n R_{globe} = \frac{V}{I} = \frac{3.0\,\text{V}}{0.2\,\text{A}} = 15.0\,\Omega\n - Part b: Three identical globes (15.0\,\Omega each) configured with Globe 1 in series with parallel pair (Globe 2 and Globe 3):\n - i. Equivalent total network resistance:\n R_{eq} = R_1 + (R_2 \parallel R_3) = 15.0 + \left(\frac{15.0 \times 15.0}{15.0 + 15.0}\right) = 15.0 + 7.5 = 22.5\,\Omega\n - ii. Total current drawn from 3\,\text{V} source:\n I_{total} = \frac{V}{R_{eq}} = \frac{3.0\,\text{V}}{22.5\,\Omega} = 0.1333\,\text{A} = 133.3\,\text{mA}\n - iii. Voltage drop across each globe:\n V_1 = I_{total} R_1 = 0.1333 \times 15.0 = 2.00\,\text{V}\n V_2 = V_3 = V - V_1 = 3.00 - 2.00 = 1.00\,\text{V}\n - iv. Individual current through each globe:\n I_1 = I_{total} = 133.3\,\text{mA}\n I_2 = I_3 = \frac{V_2}{R_2} = \frac{1.00\,\text{V}}{15.0\,\Omega} = 0.0667\,\text{A} = 66.7\,\text{mA}\n - v. Total power dissipated across all three globes:\n P_{total} = V I_{total} = 3.0\,\text{V} \times 0.1333\,\text{A} = 0.400\,\text{W} = 400\,\text{mW}\n\n- Problem 2: Single-Loop Circuit with Independent Voltage and Current Sources\n - Loop Components: 1.5\,\text{V}12\,\OmegaV_20.9\,\text{A}V_320\,\OmegaV_4).\n - Analysis:\n - Increasing 1.5\,\text{V}10\,\text{V}0.9\,\text{A} because the ideal current source dictates loop current.\n - Increasing current source setting: Voltage drop across current source (V_3) changes dynamically to satisfy KVL.\n - Voltage V_212\,\Omega0.9\,\text{A}V_2 = I R = 0.9 \times 12 = +10.8\,\text{V}.\n - Voltage V_420\,\Omega0.9\,\text{A}V_4 = I R = 0.9 \times 20 = +18.0\,\text{V}.\n - Setting current source to 0\,\text{A}I = 0V_2 = 0\,\text{V}V_4 = 0\,\text{V}V_3 = 1.5\,\text{V}.\n\n- Problem 3: Parallel Resistor Network with Multiple Current Sources\n - Circuit Topography: 0.3\,\text{A}0.1\,\text{A}12\,\Omega10\,\Omega20\,\Omega).\n - Systematic Nodal Derivation:\n 1. Express resistor current I_112\,\OmegaI_1 = \frac{V_1}{12}\n 2. Express other branch currents: I_{10} = \frac{V_1}{10}I_{20} = \frac{V_1}{20}\n 3. Formulate KCL equation at top node:\n 0.3 - 0.1 = I_1 + I_{10} + I_{20} \implies 0.2 = V_1 \left(\frac{1}{12} + \frac{1}{10} + \frac{1}{20}\right)\n 4. Solve for nodal voltage V_1:\n \frac{1}{12} + \frac{1}{10} + \frac{1}{20} = \frac{5 + 6 + 3}{60} = \frac{14}{60} = \frac{7}{30}\,\Omega^{-1}\n V_1 = 0.2 \times \frac{30}{7} = \frac{6}{7}\,\text{V} \approx 0.8571\,\text{V} = 0.857\,\text{V}\n 5. Calculate branch current I_1:\n I_1 = \frac{V_1}{12} = \frac{6/7}{12} = \frac{1}{14}\,\text{A} \approx 0.0714\,\text{A} = 71.4\,\text{mA}\n - Current Divider Shortcut Solution:\n - Combine parallel sources: I_X = 0.3 - 0.1 = 0.2\,\text{A}\n - Calculate branch current via conductances:\n I_1 = I_X \frac{12^{-1}}{12^{-1} + 10^{-1} + 20^{-1}} = 0.2 \times \frac{1/12}{7/30} = 0.0714\,\text{A} = 71.4\,\text{mA}\n\n- Problem 4: Parallel Combination in Series with Source\n - Circuit Topology: 12\,\text{V}1\,\text{k}\Omega1000\,\Omega470\,\Omega520\,\Omega resistors.\n - Step 1: Calculate equivalent parallel resistance (R_P):\n R_P = 470 \parallel 520 = \frac{470 \times 520}{470 + 520} = \frac{244400}{990} \approx 246.87\,\Omega\n - Step 2: Apply voltage divider equation to find V_1 across parallel pair:\n V_1 = 12 \times \frac{246.87}{1000 + 246.87} = 12 \times \frac{246.87}{1246.87} = 2.376\,\text{V}\n\n- Problem 5: Single-Loop KVL Equation Analysis\n - Loop Components: 6\,\text{V}12\,\Omega1.5\,\text{V}20\,\Omega10\,\Omega9\,\text{V}I_1\n - Apply KVL clockwise around loop:\n \sum V = 0 \implies (12 + 20 + 10) I_1 + (-9 + 1.5 + 6) = 0\n 42 I_1 - 1.5 = 0 \implies I_1 = \frac{1.5}{42} = 0.107\,\text{A} = 107\,\text{mA}\n\n- Problem 6: Two-Loop Circuit KCL and KVL Analysis\n - Topology: Left loop contains 2\,\text{V}15\,\OmegaI_110\,\OmegaI_325\,\OmegaI_26\,\text{V} source.\n - Node Equation: I_3 = I_1 - I_2\n - Simultaneous KVL Equations:\n - Left Loop: 2 - 15 I_1 - 10(I_1 - I_2) = 0 \implies 25 I_1 - 10 I_2 = 2\n - Right Loop: 10(I_1 - I_2) + 25 I_2 + 6 = 0 \implies 10 I_1 + 15 I_2 = -6\n - Simultaneous Solution Results:\n - Loop 1 current: I_1 = 12.9\,\text{mA}\n - Loop 2 current: I_2 = -168\,\text{mA}\n - Shared central branch current: I_3 = I_1 - I_2 = 12.9 - (-168) = 181\,\text{mA}$$