Cambridge IGCSE Physics Mastery Notes

Units and Physical Quantities

  • Measurement and Units: A standard or unit must be chosen before a measurement. Instruments have scales marked in these units.

  • SI System (Système International d’Unités): A decimal system where units are multiplied or divided by 10.

  • Basic Quantities:
        - Length: Measured in metres (mm).
        - Mass: Measured in kilograms (kgkg).
        - Time: Measured in seconds (ss).

  • Powers of Ten Shorthand (Standard Notation): Used for very large or small numbers.
        - 4000=4×1034000 = 4 \times 10^3
        - 0.004=4×10−30.004 = 4 \times 10^{-3}

  • Significant Figures: The number of figures indicates the accuracy of a measurement.
        - Rule: In calculations, the answer should have the same number of significant figures as the measurements used.
        - Rounding: If the next digit to the right is ≥5\ge 5, round up; if <5< 5, leave it.

Measurement of Length, Area, and Volume

  • Length:
        - Definition: The distance travelled by light in a vacuum during a specific time interval.
        - Submultiples: 1 dm=10−1 m1\,dm = 10^{-1}\,m, 1 cm=10−2 m1\,cm = 10^{-2}\,m, 1 mm=10−3 m1\,mm = 10^{-3}\,m, 1 μm=10−6 m1\,\mu m = 10^{-6}\,m, 1 nm=10−9 m1\,nm = 10^{-9}\,m.
        - Multiples: 1 km=103 m1\,km = 10^3\,m, 1 Gm=109 m1\,Gm = 10^9\,m.
        - Correct Reading: Eyes must be vertically over the scale mark to avoid parallax error.
        - Average Values: To measure small lengths (e.g., thickness of paper), measure multiples and divide (e.g., measure 100 sheets and divide by 100).

  • Area:
        - Formula: length×breadth\text{length} \times \text{breadth}.
        - Triangles: 12×base×height\frac{1}{2} \times \text{base} \times \text{height}.
        - Circles: Area=πr2\text{Area} = \pi r^2; Circumference=2πr\text{Circumference} = 2\pi r.
        - Unit: Square metre (m2m^2).

  • Volume:
        - Formula (Rectangular block): length×breadth×height\text{length} \times \text{breadth} \times \text{height}.
        - Cylinder: πr2h\pi r^2h.
        - Liquid Measurement: Use a measuring cylinder. Read at the bottom of the meniscus (except for mercury, read the top).
        - Displacement Method (Irregular Solids): Submerge the object in a measuring cylinder or displacement can; the increase in volume equals the solid's volume.

Measurement of Time and Errors

  • Time:
        - Unit: Second (ss). Defined by energy changes in the caesium atom.
        - Devices: Traditional (balance wheel), Digital (quartz crystal), Pendulum (swinging bob).
        - Period of a Pendulum (TT): The time for one complete oscillation. To improve accuracy, time many oscillations and calculate the average (T=total timenumber of oscillationsT = \frac{\text{total time}}{\text{number of oscillations}}).
        - Frequency (ff): f=1Tf = \frac{1}{T}.

  • Systematic Errors: Errors introduced by the system/apparatus (e.g., a ruler with a space before the zero mark). These must be added/subtracted for accuracy.

  • Precision Tools:
        - Vernier Calipers: Measure to 0.01 cm0.01\,cm. Uses a small sliding scale.
        - Micrometer Screw Gauge: Measures to 0.001 cm0.001\,cm. Rotation of the drum opens jaws. Includes a friction clutch to apply uniform pressure.

Scalars and Vectors

  • Scalar: Has magnitude (size) only. Examples: distance, speed, time, mass, energy, temperature, pressure.

  • Vector: Has both magnitude and direction. Examples: displacement, velocity, acceleration, force, weight, momentum.

  • Resultant of Perpendicular Vectors:
        - For two vectors FXF_X and FYF_Y at right angles:
        - Magnitude: F=FX2+FY2F = \sqrt{F_X^2 + F_Y^2}
        - Direction: tan⁡(θ)=FYFX\tan(\theta) = \frac{F_Y}{F_X}
        - Graphical Method: Draw a rectangle using vectors as sides; the diagonal from the origin is the resultant.

Motion

  • Speed: speed=distancetime taken\text{speed} = \frac{\text{distance}}{\text{time taken}}. Average speed = total distancetotal time\frac{\text{total distance}}{\text{total time}}.

  • Velocity: Velocity is speed in a given direction (velocity=displacementtime taken\text{velocity} = \frac{\text{displacement}}{\text{time taken}}).

  • Acceleration (aa): The change in velocity per unit time.
        - a=Δvt=v−uta = \frac{\Delta v}{t} = \frac{v - u}{t}
        - Units: m/s2m/s^2.
        - Deceleration: Negative acceleration (speeding down).

  • Graphs of Motion:
        - Distance–time graph: Gradient = Speed.
        - Speed–time graph: Gradient = Acceleration. Area under the curve = Distance travelled.

  • Equations of Motion (Constant Acceleration):
        - v=u+atv = u + at
        - s=(u+v2)ts = \left(\frac{u + v}{2}\right)t
        - s=ut+12at2s = ut + \frac{1}{2}at^2
        - v2=u2+2asv^2 = u^2 + 2as (Extended syllabus)

Falling Bodies and Gravity

  • Free Fall: All objects fall with uniform acceleration if air resistance is negligible.

  • Acceleration of free fall (gg): Approximately 9.8 m/s29.8\,m/s^2 (often taken as 10 m/s210\,m/s^2) near Earth's surface.

  • Terminal Velocity: As an object falls, air resistance increases with speed. When upward air resistance equals downward weight, the resultant force is zero, and the object falls at a constant terminal velocity.

  • Projectiles: Horizontal and vertical motions are independent. Vertical motion is accelerated by gravity (gg); horizontal motion has constant velocity (ignoring air resistance).

Mass, Weight, and Density

  • Mass (mm): Quantity of matter in an object at rest relative to an observer. Measured in kilograms (kgkg).

  • Weight (WW): The gravitational force on an object. Measured in newtons (NN).
        - W=mgW = mg

  • Gravitational Field Strength (gg): Force per unit mass.
        - g=Wmg = \frac{W}{m}
        - On Earth, g≈9.8 N/kgg \approx 9.8\,N/kg. On the Moon, g≈1.6 N/kgg \approx 1.6\,N/kg.

  • Density (ρ\rho): Mass per unit volume.
        - ρ=mV\rho = \frac{m}{V}
        - SI Unit: kg/m3kg/m^3. Common unit: g/cm3g/cm^3 (1 g/cm3=1000 kg/m31\,g/cm^3 = 1000\,kg/m^3).

  • Floating and Sinking: An object sinks if its density is greater than the liquid's density. A less dense liquid will float on a denser liquid if they do not mix.

Forces and Effects

  • Effects of Force: A force (push/pull) can change an object's speed, direction of motion, size, or shape.

  • Hooke’s Law: For a spring, extension is proportional to the stretching force, provided the limit of proportionality is not exceeded.
        - Spring Constant (kk): Force per unit extension.
        - F=kxF = kx

  • Newton’s First Law: An object stays at rest or moves in a straight line at constant speed unless acted on by a resultant force.

  • Newton’s Second Law: Force equals mass times acceleration.
        - F=maF = ma

  • Newton’s Third Law: If body A exerts a force on body B, body B exerts an equal but opposite force on body A.

  • Friction: A force that opposes motion.
        - Solid Friction: Impedes motion between surfaces and produces heat.
        - Drag/Air Resistance: Opposes motion through fluids (gas/liquid); increases with speed.

  • Circular Motion: Motion in a circular path requires a perpendicular centripetal force acting towards the center.
        - Force increases if speed or mass increases, or if radius decreases.

Turning Effects and Equilibrium

  • Moment of a Force: The turning effect.
        - Moment=force×perpendicular distance from pivot\text{Moment} = \text{force} \times \text{perpendicular distance from pivot}.

  • Principle of Moments: For an object in equilibrium, total clockwise moments = total anticlockwise moments.

  • Equilibrium Conditions: (1) No resultant force. (2) No resultant moment.

  • Centre of Gravity: The point through which all of an object’s weight acts.

  • Stability: A body is more stable if its centre of gravity is low and its base is wide. An object topples if its weight's line of action falls outside its base.

Momentum

  • Definition: Mass multiplied by velocity.
        - p=mvp = mv
        - Units: kg m/skg\,m/s or NsNs.

  • Conservation of Momentum: Total momentum remains constant in a collision if no external forces act.

  • Impulse: Force multiplied by time.
        - Impulse=FΔt=Δ(mv)\text{Impulse} = F\Delta t = \Delta(mv).

  • Resultant Force: The rate of change of momentum.
        - F=ΔptF = \frac{\Delta p}{t}

Energy, Work, and Power

  • Energy Stores: Kinetic, gravitational potential, chemical, elastic (strain), nuclear, electrostatic, internal (thermal).

  • Energy Transfers: Mechanical working, electrical working, waves (light/sound), heating.

  • Conservation of Energy: Energy cannot be created or destroyed, only transferred.

  • Kinetic Energy (EkE_k): Ek=12mv2E_k = \frac{1}{2}mv^2.

  • Gravitational Potential Energy (EpE_p): ΔEp=mgh\Delta E_p = mgh.

  • Work Done (WW): Energy transferred by a force.
        - W=F×d=ΔEW = F \times d = \Delta E
        - Unit: Joule (JJ).

  • Power (PP): Work done per unit time.
        - P=Wt=ΔEtP = \frac{W}{t} = \frac{\Delta E}{t}
        - Unit: Watt (WW) (1 W=1 J/s1\,W = 1\,J/s).

  • Efficiency:
        - Efficiency=useful energy outputtotal energy input×100%\text{Efficiency} = \frac{\text{useful energy output}}{\text{total energy input}} \times 100\%
        - Efficiency=useful power outputtotal power input×100%\text{Efficiency} = \frac{\text{useful power output}}{\text{total power input}} \times 100\%

Pressure

  • Definition: Force per unit area.
        - p=FAp = \frac{F}{A}
        - Unit: Pascal (PaPa).

  • Liquid Pressure: Increases with depth and density.
        - Δp=ρgΔh\Delta p = \rho g \Delta h

  • Hydraulic Machines: Rely on the fact that liquids are incompressible and transmit pressure equally.
        - Force Multiplier: F=f×AaF = f \times \frac{A}{a}