Detailed Notes on Pulling Motions in Weightlifting

Pulling Motion in Weightlifting

Introduction to Pulling Motions

  • Pulling motions, including snatch pulls and clean pulls, are crucial for translating weightlifting to sports performance.
  • These are referred to as "weightlifting derivatives" by Professor Tim Suchomel.
  • Understanding these motions within the context of weightlifting movements is key.

Foundational Research by Professor Kale Hakonen

  • Professor Kale Hakonen's 1984 research is highly regarded in sports science.
  • His work uses European terminology: "pole, pole, pole" which translates to "pull, transition, pull".
  • In clean and jerk or snatch, phases include a concentric phase (lifting the bar), an unweighting phase (knee reorientation in the double knee bend), and an eccentric load phase (slowing the bar down).
  • The final phase involves a high rate of force development as the lifter extends.

Comparison to Vertical Jump

  • The jerk motion shares similarities with a vertical jump trajectory, including a countermovement, braking phase, drive, and flight time.

Full Snatch vs. Power Snatch

  • Full Snatch: Barbell received below parallel (top of the thigh below parallel).
  • Power Snatch: Barbell received above parallel (top of the thigh above parallel).
  • Power snatch involves a faster pull, faster rate of force development, and faster eccentric load due to quicker bracing.
  • More force is required in a power snatch to elevate the barbell higher compared to a full snatch.
  • Interesting data indicates distinct benefits for both lifts.

Knee Angle and Performance

  • Professor Roger Anoka's work emphasizes the changing knee angle and its impact on performance.
  • The lifter extends from the trunk, straightening the knee.
  • The knee bend or double knee bend is crucial for barbell elevation.

Barbell Position, Velocity, and Acceleration

  • Three key factors: barbell position, velocity, and acceleration.
  • Acceleration occurs off the floor, followed by deceleration during the transition, and re-acceleration to get the barbell overhead.
  • This pattern of acceleration-deceleration-re-acceleration is significant.
  • The pulling motion involves three acceleration points: after the pull, during the shift to the top of the thigh, and to finish the pull.
  • Lifters generally move backward to receive the bar; jumping forward indicates excessive pressure on the front of the foot.

Center of Pressure and Barbell Trajectory

  • As the barbell breaks the floor, the lifter moves backward, maintaining a zero position for the center of pressure.
  • At the end of the pull, the lifter shifts forward to the forefoot.
  • Barbell velocity increases through the pull, slowing slightly in the transition before re-accelerating.
  • Better lifters slow down less during the transition.

Barbell Trajectory and Efficiency

  • Mike Stone and Jason Winchester's research shows the barbell trajectory reflects the efficiency of the pulling motion.
  • If the barbell is pulled forward, the lift is more likely to fail from the floor.
  • A smaller DXV (displacement) indicates greater success.
  • A wider DXT (start to catch position) indicates a greater chance of missing the lift.
  • The goal is to keep the bar close to the body with minimal looping, moving vertically.

Types of Barbell Trajectories

  • Three types of curves, as defined by Vorboyev:
    • Type C: Most efficient trajectory.
    • Type B: Inefficient; involves jumping forward.
    • Type A.
  • Successful lifts have less looping and higher peak force.
  • A slight pole position or C curve is preferred; jumping forward (B curve) increases the chance of missing the lift.
  • Jumping more than 2020 cm behind the start position results in failure.
  • The mean loop for successful attempts is around 1111 cm.
  • Excessive arm usage and "hipping" the bar, often seen in CrossFit, are problematic.

Coaching Implications

  • Effectively coaching weightlifting requires understanding the point motion and barbell position relative to the body.
  • This understanding enables the effective implementation of pulling motions for developing weightlifting-based exercises.