Propeller Principles and Operation

Propeller Basics

  • A propeller absorbs engine power and converts it into thrust.
  • Early propellers were simple, fabric-covered sticks.
  • Modern propellers are complex systems, especially in turboprop aircraft.
  • Variable-pitch, constant-speed, feathering, and reversing propeller systems have been developed to increase flying efficiency.
  • Constant-speed systems use a flyweight-equipped governor to control blade pitch angle, maintaining constant engine speed.
  • Low-pitch, high-rpm settings are used for takeoff, while higher pitch and lower rpm settings are used after takeoff.
  • Propeller efficiency is affected by "slip," the difference between geometric and effective pitch.

Propeller Components and Nomenclature

  • Leading edge: The front edge of the propeller blade that meets the air.
  • Trailing edge: The rear edge of the propeller blade.
  • Blade tip: The farthest point from the hub.
  • Hub: The central part to which the blades are attached.
  • Blade back: The curved side of the blade, similar to the upper surface of a wing.
  • Blade face: The flat side of the propeller blade.
  • Angle of attack: The angle between the relative wind and the chord line of the blade.
  • Chord line: An imaginary line from the leading edge to the trailing edge of the blade.

Propeller Limitations and Evolution

  • Propeller-driven aircraft are limited in speed to approximately 400 mph due to propeller tip speed limitations.
  • Turbofan engines are used for higher speed aircraft.
  • New materials and manufacturing techniques have increased propeller efficiency.
  • A constant-speed system maintains near constant engine RPM by adjusting the blade pitch.
  • The pilot can control the blade angle and engine operating speed from the flight deck.

Propeller Range Positions

  • Feather: 85 to 90 degrees, used to reduce drag when an engine quits.
  • High Pitch: 20 to 35 degrees
  • Low Pitch: 10 to 12 degrees
  • Locks/Ground Idle: 1 to 2 degrees
  • Ground Idle: 0 degrees
  • Reverse: -2 to -8 degrees, used for braking after landing.

Aerodynamic Principles

  • Propeller blades are rotating wings that produce thrust.
  • Thrust is the force that propels the aircraft forward and must equal drag for level flight.
  • Work=Thrust×DistanceWork = Thrust \times Distance
  • Power=Thrust×VelocityPower = Thrust \times Velocity
  • Thrust horsepower is the power expended by the thrust.
  • Propeller efficiency (η) is the ratio of thrust horsepower to brake horsepower, ranging from 50% to 87%.

Propeller Pitch and Blade Angle

  • Geometric pitch is the distance a propeller should advance in one revolution with no slippage.
  • Effective pitch is the distance it actually advances, accounting for slippage.
  • Geometric pitch−Effective pitch=slipGeometric\ pitch - Effective\ pitch = slip
  • GP=2×π×R×tangent of blade angle at 75 percent stationGP = 2 \times π \times R \times tangent\ of\ blade\ angle\ at\ 75\ percent\ station
    • GP = Geometric Pitch
    • π=3.14π = 3.14
    • R = Radius at 75% blade station
  • Blade angle is the angle between the chord of a blade section and the plane of rotation.

Propeller Blade Elements

  • Propeller blades can be divided into segments for analysis, located by station numbers in inches from the hub center.
  • The blade shank is the thick, rounded portion near the hub for strength.
  • The blade butt is the end of the blade that fits into the propeller hub.
  • The blade tip is the farthest part from the hub, generally the last 6 inches.

Forces Acting on a Rotating Propeller

  • Centrifugal Force: Tends to pull the blades out of the hub (dominant force).
  • Torque Bending Force: Air resistance bends the blades opposite the direction of rotation.
  • Thrust Bending Force: Thrust load bends the blades forward.
  • Aerodynamic Twisting Force: Turns the blades to a high blade angle.
  • Centrifugal Twisting Force: Forces the blades toward a low blade angle.

Propeller Stresses and Rigidity

  • Propellers must withstand severe stresses from centrifugal force and thrust, especially near the hub.
  • Nicks or scratches can lead to cracks and blade failure.
  • Propellers must be rigid enough to prevent fluttering, a high-frequency vibration that can cause failure.

Aerodynamic Factors and Angle of Attack (AOA)

  • The relative wind strikes the propeller blade at the angle of attack (AOA).
  • Air deflection creates dynamic pressure, generating thrust.
  • Thrust is also produced by the propeller shape, similar to a wing, creating lift in a forward direction.
  • Thrust is equal to the mass of air handled multiplied by the slipstream velocity minus the aircraft velocity.
  • Approximately 80% of the torque is converted to thrust, with 20% lost to friction and slippage.

Blade Angle and Engine RPM Control

  • Blade angle adjusts the load on the propeller to control engine rpm.
  • Increasing blade angle increases AOA, lift, and drag, slowing the engine unless more power is applied.
  • Decreasing blade angle speeds up the propeller.

Constant-Speed Propellers and AOA

  • Constant-speed propellers adjust blade angle for maximum efficiency at all engine and aircraft speeds.
  • The most efficient AOA is a small one, varying from 2° to 4° positive.
  • Fixed-pitch propellers are designed for best efficiency at one rotation and forward speed.

Constant-Speed Propeller Operation

  • During takeoff, a low blade angle keeps AOA small, allowing high rpm and maximum thrust.
  • After liftoff, blade angle increases to maintain efficient AOA, reducing fuel consumption and engine wear.
  • For climb, manifold pressure is reduced, and blade angle is increased to lower rpm.
  • At cruising altitude, manifold pressure is reduced further, and blade angle increases to decrease rpm.

Pitch Distribution

  • Pitch distribution is the twist in the blade from shank to tip, accommodating the varying speeds of each section.

Propeller Controls and Instruments

  • Fixed-pitch propellers have no controls.
  • Constant-speed propellers have a control to increase or decrease rpm, connected to the propeller governor.
  • Engine tachometer measures RPM.
  • Manifold pressure gauge indicates manifold pressure, which is adjusted by the throttle.

Propeller Location

  • Tractor Propellers: Mounted on the upstream end of a drive shaft, in front of the supporting structure. Lower stresses are induced on the propeller.
  • Pusher Propellers: Mounted on the downstream end of the drive shaft, behind supporting structure. More prone to damage.

Types of Propellers

  • Fixed-Pitch: Blade angle cannot be changed.
  • Test Club: Used for engine testing and break-in.
  • Ground-Adjustable: Pitch can be changed only when the propeller is not turning.
  • Controllable-Pitch: Blade pitch can be changed while rotating.
  • Constant-Speed: Uses a governor to automatically adjust blade pitch to maintain constant engine RPM.

Constant-Speed Propellers

  • The propeller has a natural tendency to slow down as the aircraft climbs.
  • Propeller governors are used to increase or decrease propeller pitch, the engine speed is held constant.
  • The governor-controlled, constant-speed propeller changes the blade angle automatically, keeping engine rpm constant.
  • One type of pitch-changing mechanism is operated by oil pressure (hydraulically) and uses a piston-and-cylinder arrangement.

Constant-Speed Propeller Systems - Operation

  • Maintain constant engine rpm.
  • If engine speed increases (overspeed condition), the controls automatically increase the blade angle until desired rpm is reestablished.
  • Each constant-speed propeller has an opposing force that operates against the oil pressure from the governor.

Feathering Propellers

  • Used on multi-engine aircraft to minimize drag after engine failure rotate the propeller blade angle parallel to the line of flight.
  • Almost all small feathering propellers use oil pressure to take the propeller to low pitch, and blade flyweights, springs, and compressed air to take the blades to high pitch.
  • Latches lock the propeller in the low pitch position as the propeller slows down at shutdown.

Reverse-Pitch Propellers

  • Included in some propellers to improve their operational characteristics (mainly used on turbo props).
  • Almost all reverse-pitch propellers are of the feathering type.
  • Produce a negative blade angle that creates thrust opposite the normal forward direction.
  • Aerodynamically brakes the aircraft and reduces ground roll after landing and also minimizes aircraft brake wear.

Propeller Governor

  • A governor is an engine rpm-sensing device and high-pressure oil pump.
  • Senses propeller and engine speed.
  • The governor is set for a specific rpm via the flight deck propeller control, which compresses or releases the governor speeder spring.

Forces Controlling Blade Angle Variations

  1. Centrifugal twisting moment:
    Tends to move the blade into low pitch.
  2. Propeller-governor oil on the propeller piston side:
    Balances the propeller blade flyweights, which moves the blades toward high pitch.
  3. Propeller blade flyweights:
    Always move the blades toward high pitch.
  4. Air pressure against the propeller piston:
    Pushes toward high pitch.
  5. Large springs:
    Push in the direction of high pitch and feather.
  6. Centrifugal twisting force:
    Moves the blades toward low pitch.
  7. Aerodynamic twisting force:
    Moves the blades toward high pitch.

Governor Mechanism

  • The engine-driven single-acting propeller governor increases the pressure of the engine oil.
  • Speeder spring opposes the governor flyweight’s ability to fly outward when turning.
  • The tension of the speeder spring sets the maximum rpm of the engine in the governor mode.

Underspeed Condition

  • The engine is operating below the rpm set with the flight control.
  • Not enough centrifugal force on the flyweights to overcome the force of the speeder spring.
  • Meters oil flow to decrease propeller pitch and raise engine rpm.

Overspeed Condition

  • The engine is operating above the rpm set with the flight control.
  • The centrifugal force acting on the flyweights is greater than the speeder spring force.
  • Meters oil flow to increase propeller pitch and lower engine rpm.

On-Speed Condition

  • The engine is operating at the rpm set by the pilot using the flight deck control.
  • In an on-speed condition, the centrifugal force acting on the flyweights is balanced by the speeder spring.
  • The propeller blades are not moving or changing pitch.

Fixed-Pitch Wooden Propellers

  • Blade pitch cannot be changed after manufacture.
  • Restricts its use to small aircraft with low horsepower engines.
  • Light weight, rigidity, economy of production, simplicity of construction, and ease of replacement.
  • Constructed from a number of separate layers of carefully selected and well-seasoned hardwoods glued together with a waterproof, resinous glue.

Metal Fixed-Pitch Propellers

  • Thinner than wooden propellers.
  • Lighter in weight. Lower maintenance cost.
  • More efficient cooling.
  • Propeller pitch could be changed, within limits, by twisting the blade slightly by a propeller repair station manufactured as one-piece anodized aluminum alloy.

Constant-Speed Propellers

  • Hartzell Constant-Speed, Nonfeathering propellers combine low weight and simplicity in design and rugged construction.
  • One model of nonfeathering aluminum hub constant-speed propeller utilizes oil pressure from a governor to move the blades into high pitch (reduced rpm).
  • Many types of light aircraft use governor-regulated, constant-speed propellers in two-bladed and up to six-bladed versions.

Constant-Speed Feathering Propellers

  • The feathering propeller utilizes a single oil supply from a governing device to hydraulically actuate a change in blade angle.
  • Hydraulically actuated piston transmits linear motion through a pitch change rod and fork to each blade to result in blade angle change.
  • Spring and flyweight forces attempt to rotate the blades to higher blade angle, while the centrifugal twisting moment of each blade is generally toward lower blade angle.
  • Feathering occurs because the summation of internal propeller forces causes the oil to drain out of the propeller until the feather stop position is reached

Unfeathering

  • Start the engine, so the governor can pump oil back into the propeller to reduce pitch.
  • Provide an accumulator connected to the governor with a valve.
  • Provide an unfeathering pump that provides pressure to force the propeller back to low pitch quickly using engine oil.

Ice Control Systems

  • Ice formation on a propeller blade, in effect, produces a distorted blade airfoil section that causes a loss in propeller efficiency.
  • Anti-Icing Systems
    A typical fluid system.
  • Deicing Systems
    An electric propeller-icing control system.

Propeller Synchronization & Synchrophasing

  • Synchronization systems provide a means of controlling and synchronizing engine rpm.
  • Synchrophasing system is designed to maintain a preset angular relationship between the designated master propeller and the slave propellers.

Autofeathering System

  • Used normally only during takeoff, approach, and landing.
  • Used to feather the propeller automatically if power is lost from either engine.

Propeller Inspection & Maintenance

  • Propellers must be inspected regularly. The exact time interval for particular propeller inspections is usually specified by the propeller manufacturer.
  • The propeller should be disassembled and inspected.
  • It is also vitally important to keep up-to-date airworthiness directives (ADs) or service bulletins (SBs) for a propeller.

Wood Propeller Inspection

  • Wood propellers should be inspected frequently to ensure airworthiness.
  • Inspect for defects, such as cracks, dents, warpage, glue failure, delamination defects in the finish, and charring of the wood between the propeller and the flange due to loose propeller mounting bolts.

Metal Propeller Inspection

  • Metal propellers and blades are generally susceptible to fatigue failure resulting from the concentration of stresses at the bottoms of sharp nicks, cuts, and scratches. It is necessary, therefore, to frequently and carefully inspect them for such defects and make repairs promptly.

Aluminum Propeller Inspection

  • Transverse crack or flaw of any size is cause for rejection. Multiple deep nicks and gouges on the leading edge and face of the blade is cause for rejection.

Composite Propeller Inspection

  • Composite blades need to be visually inspected for nicks, gouges, loose material, erosion, cracks and debonds, and lightning strike.

Propeller Vibration

  • Vibration can be caused by the propeller, but there are numerous other possible sources of vibration that can make troubleshooting difficult.
  • The ideal troubleshooting method is to temporarily replace the propeller with one known to be airworthy and then test fly the aircraft if possible.

Blade Tracking

  • The process of determining the positions of the tips of the propeller blades relative to each other (blades rotating in the same plane of rotation).
  • Verify the propeller blade tracking at installation.
  • Each blade track should be within 1⁄16 inch.

Universal Propeller Protractor

  • The universal propeller protractor can be used to check propeller blade angles when the propeller is on a balancing stand or installed on the aircraft engine.
  • Keep the protractor vertical by the corner spirit level and turn the disc adjuster until the center spirit level is horizontal.

Static Balancing

  • Knife-edge test stand has two hardened steel edges mounted to allow the free rotation of an assembled propeller between them.

Dynamic Balancing

  • Propellers can also be dynamically balanced (spin balanced) with an analyzer kit to reduce the vibration levels of the propeller and spinner assembly.
  • Face the aircraft directly into the wind (maximum 20 knots) and place chocks at the wheels.
  • Always refer to the aircraft and propeller manuals.

Propeller Removal & Installation

  • Always use the current manufacturer’s information.
  • Support the propeller assembly with a sling.
  • Using the support sling, remove the propeller from the mounting flange.

Servicing Propellers

  • Propeller servicing includes cleaning, lubricating, and replenishing operating lubrication supplies.
  • Aluminum and steel propeller blades and hubs are usually cleaned by washing the blades with a suitable cleaning solvent.

Propeller Lubrication

  • Hydromatic propellers operated with engine oil and some sealed propellers do not require lubrication. Electric propellers require oils and greases for hub lubricants and pitch change drive mechanisms.

Propeller Overhaul

  • Overhaul the propellers at the correct time intervals.
  • Components that are subject to wear must be inspected, dimensionally.

Troubleshooting Propellers

  • Always refer to the correct manual for actual information on troubleshooting propellers.
  • Hunting & Surging, characterized by a cyclic variation in engine speed above and below desired speed. Surging is characterized by a large increase/decrease in engine speed
  • Failure to Feather or Feathers Slowly

Turboprop Engines & Propeller Control Systems

  • Most turboprop engines is the that turbine inlet temperature determines power, which maintains a constant engine speed.
  • Turboprop fuel control and the propeller governor are connected and operate in coordination with each other.

Turboprop Assembly

  • The turbo-propeller provides an efficient and flexible means of using the power of the engine at any condition in flight (alpha range).

Hamilton Standard Hydromatic Propellers

  • A hydromatic propeller has a double-acting governor that uses oil pressure on both sides of the propeller piston.
  • Double-acting hydraulic propeller system in which the hydraulic pressure (engine oil pressure) on one piston dome is used against governor oil pressure on the other side of the piston.

Turboprop Commuter Operations

  • Hydromatic propeller. For single acting propeller or double acting propeller.
  • The same conditions described for underspeed operation exist in the distributor valve, except that oil at auxiliary pressure replaces drain oil at the inboard end of the land and between lands.