Laboratory Experiment: Interference and Diffraction

Objectives and Overview

  • Experimental Goals:
    • Examine the physical phenomena of optical interference and diffraction.
    • Gain practical familiarity with single-slit diffraction and double-slit interference.
    • Develop advanced technical competence in writing formal laboratory reports.

Part I: Visualizing Diffraction Patterns and Measuring Key Locations

  • Single-Slit Diffraction Procedure & Data Collection:

    • Attach a blank sheet of paper to the viewing screen.
    • Mark the exact physical locations of the dark minima on the paper.
    • Draw an arrow to mark the precise location of the central maximum.
    • Measure the distance from the single slit to the screen.
    • Remove the paper from the screen to proceed with data analysis.
  • Single-Slit Data Analysis Protocol:

    • Measure and record the separation distance between symmetric pairs of minima moving outward from the central maximum (1st pair, 2nd pair, 3rd pair, etc.) into a spreadsheet.
    • Divide each measured separation distance by 22 to calculate the position distance from the central maximum to a given minimum (denoted as y1ny_{1n} for the first minimum, y2ny_{2n} for the second minimum, and so forth).
    • Calculate the angle θn\theta_n corresponding to each minimum using basic trigonometry.
    • Apply the single-slit diffraction equation:

sin⁡(θn)=nλa\sin(\theta_n) = \frac{n \lambda}{a}

*   Calculate the slit width aa and estimate the associated measurement uncertainty.
*   Light source parameters: A diode laser with a wavelength of λ=650 nm\lambda = 650\,nm is used. Note that nn represents an integer index.
  • Two-Slit Interference Procedure & Data Collection:

    • Attach a sheet of paper to the screen.
    • Mark the locations of the individual interference maxima on the paper.
    • Draw an arrow to mark the location of the central maximum (the center of the central bright spot).
    • Place "x" marks at the locations of the first few single-slit diffraction envelope minima.
    • Measure the distance from the double slit to the screen.
    • Remove the paper from the screen for analysis.
  • Two-Slit Data Analysis Protocol:

    • Measure and record the distance between pairs of single-slit minima moving outward from the central maximum. Use these measurements to calculate the single-slit width aa as done previously.
    • Measure and record the separation distance between pairs of interference maxima moving outward from the central maximum.
    • Divide each separation distance by 22 to obtain the distance from the central maximum to a given maximum or minimum (denoted as y1sy_{1s} for the first maximum, y2sy_{2s} for the second maximum, etc.).
    • Calculate the corresponding angles θm\theta_m using trigonometry.
    • Apply the slit interference formula:

sin⁡(θs)=mλd\sin(\theta_s) = \frac{m \lambda}{d}

*   Calculate the slit separation distance dd and estimate the experimental uncertainty.

Part II: Measuring and Comparing Intensity Distributions

  • Experimental Apparatus & Setup:

    • Combines a light sensor with a linear travel sensor to record light intensity continuous as a function of position using Logger Pro software.
    • Record all experimental parameters: slit width (aa), slit separation (dd), light wavelength (λ\lambda), slit-to-detector distance (LL), and any other relevant setup parameters.
    • Sensor Saturation Warning: If recorded intensity peaks display flat tops, the light sensor is saturated. Adjust the light sensor sensitivity setting and repeat the data acquisition.
  • Data Processing & Normalization:

    • To normalize data for comparison with theory, determine the maximum intensity I0I_0 and divide all intensity values by I0I_0, yielding normalized intensity II0\frac{I}{I_0}.
    • Shift the peak position to zero by subtracting the offset position value from all recorded position coordinates.
  • Spreadsheet Theoretical Model Setup:

    • Column 1: Create a series of position values incremented by a small step size, covering the full experimental range, centered with the peak at zero position.
    • Column 2: Calculate single-slit diffraction intensity at each position using Equation 1.33.
    • Column 3: Calculate double-slit interference intensity at each position using Equation 1.34.
    • Column 4: Calculate the composite double-slit diffraction pattern at each position using Equation 1.35 (or by multiplying Column 2 by Column 3).
  • Plotting and Comparison Requirements:

    • Plot single-slit intensity (alone), double-slit intensity (alone), and composite double-slit diffraction intensity as functions of position.
    • Compare theoretical plots against experimental measurements. Proper unit conversions will yield quantitative agreement with Equation 1.35.
  • Formal Lab Report Specifications:

    • Part I Requirements: Verify manufacturer specifications for slit width aa and slit separation dd. Present data in tabular form, detail uncertainty estimates, and discuss agreement or discrepancy between listed and calculated values.
    • Part II Requirements: Include a concise summary of the theoretical derivation. Show explicitly that positions where single-slit intensity equals zero correspond to the single-slit minima equation asin⁡(θ)=nλa \sin(\theta) = n \lambda. Show that double-slit intensity maxima correspond to dsin⁡(θ)=mλd \sin(\theta) = m \lambda. Analyze and discuss any observed differences between theoretical predictions and measured experimental data.

Theoretical Derivation of Single-Slit Diffraction Intensity

  • Electromagnetic Field and Intensity Relationship:
    • Light intensity II is proportional to the time average of the Poynting vector magnitude SS, which is proportional to the square of the electric field EE:

I∝⟨S⟩∝⟨E2⟩I \propto \langle S \rangle \propto \langle E^2 \rangle

  • Huygens' Principle Sub-Division:
    • A single slit of width aa is divided into NN small discrete zones, each having a width:

Δy=aN\Delta y = \frac{a}{N}

*   Assuming Δy≪λ\Delta y \ll \lambda, light across each individual zone remains in phase.
*   The path difference Δ\Delta between adjacent zones at angle θ\theta is:

Δ=Δysin⁡(θ)\Delta = \Delta y \sin(\theta)

*   The relative phase shift Δβ\Delta \beta between adjacent zones is given by:

Δβ=2πλΔ=2πλΔysin⁡(θ)\Delta \beta = \frac{2 \pi}{\lambda} \Delta = \frac{2 \pi}{\lambda} \Delta y \sin(\theta)

  • Electric Field Vector Summation:
    • Let the electric field from the first zone at screen point PP be:

E1=E10sin⁡(ωt)E_1 = E_{10} \sin(\omega t)

*   The electric field contribution from the second zone is:

E2=E10sin⁡(ωt+Δβ)E_2 = E_{10} \sin(\omega t + \Delta \beta)

*   The electric field from the NNth zone is:

EN=E10sin⁡(ωt+(N−1)Δβ)E_N = E_{10} \sin(\omega t + (N - 1) \Delta \beta)

*   The complete electric field at point PP is the superposition sum:

E=E1+E2+⋯+EN=E10[sin⁡(ωt)+sin⁡(ωt+Δβ)+⋯+sin⁡(ωt+(N−1)Δβ)]E = E_1 + E_2 + \dots + E_N = E_{10} \left[ \sin(\omega t) + \sin(\omega t + \Delta \beta) + \dots + \sin(\omega t + (N - 1) \Delta \beta) \right]

*   The total phase shift β\beta across the entire slit from zone 1 to zone NN is:

β=NΔβ=2πλNΔysin⁡(θ)=2πλasin⁡(θ)\beta = N \Delta \beta = \frac{2 \pi}{\lambda} N \Delta y \sin(\theta) = \frac{2 \pi}{\lambda} a \sin(\theta)

  • Trigonometric Reduction Sequence:
    • Using the trigonometric product identity:

cos⁡(α−β)−cos⁡(α+β)=2sin⁡(α)sin⁡(β)\cos(\alpha - \beta) - \cos(\alpha + \beta) = 2 \sin(\alpha) \sin(\beta)

*   Apply the identity sequentially across terms:

cos⁡(ωt−Δβ2)−cos⁡(ωt+Δβ2)=2sin⁡(ωt)sin⁡(Δβ2)\cos\left(\omega t - \frac{\Delta \beta}{2}\right) - \cos\left(\omega t + \frac{\Delta \beta}{2}\right) = 2 \sin(\omega t) \sin\left(\frac{\Delta \beta}{2}\right)

cos⁡(ωt+Δβ2)−cos⁡(ωt+3Δβ2)=2sin⁡(ωt+Δβ)sin⁡(Δβ2)\cos\left(\omega t + \frac{\Delta \beta}{2}\right) - \cos\left(\omega t + \frac{3 \Delta \beta}{2}\right) = 2 \sin(\omega t + \Delta \beta) \sin\left(\frac{\Delta \beta}{2}\right)

cos⁡(ωt+3Δβ2)−cos⁡(ωt+5Δβ2)=2sin⁡(ωt+2Δβ)sin⁡(Δβ2)\cos\left(\omega t + \frac{3 \Delta \beta}{2}\right) - \cos\left(\omega t + \frac{5 \Delta \beta}{2}\right) = 2 \sin(\omega t + 2 \Delta \beta) \sin\left(\frac{\Delta \beta}{2}\right)

cos⁡(ωt+(N−32)Δβ)−cos⁡(ωt+(N−12)Δβ)=2sin⁡(ωt+(N−1)Δβ)sin⁡(Δβ2)\cos\left(\omega t + \left(N - \frac{3}{2}\right) \Delta \beta\right) - \cos\left(\omega t + \left(N - \frac{1}{2}\right) \Delta \beta\right) = 2 \sin(\omega t + (N - 1) \Delta \beta) \sin\left(\frac{\Delta \beta}{2}\right)

*   Summing all equations results in a telescoping cancellation where only the very first and very last cosine terms survive:

cos⁡(ωt−Δβ2)−cos⁡(ωt+(N−12)Δβ)=2sin⁡(Δβ2)[sin⁡(ωt)+sin⁡(ωt+Δβ)+⋯+sin⁡(ωt+(N−1)Δβ)]\cos\left(\omega t - \frac{\Delta \beta}{2}\right) - \cos\left(\omega t + \left(N - \frac{1}{2}\right) \Delta \beta\right) = 2 \sin\left(\frac{\Delta \beta}{2}\right) \left[ \sin(\omega t) + \sin(\omega t + \Delta \beta) + \dots + \sin(\omega t + (N - 1) \Delta \beta) \right]

*   Applying the sum-to-product rule:

cos⁡(α)−cos⁡(β)=−2sin⁡(α+β2)sin⁡(α−β2)\cos(\alpha) - \cos(\beta) = -2 \sin\left(\frac{\alpha + \beta}{2}\right) \sin\left(\frac{\alpha - \beta}{2}\right)

*   Recasting the left-hand side yields (noting that sine is an odd function, sin⁡(−x)=−sin⁡(x)\sin(-x) = -\sin(x)):

cos⁡(ωt−Δβ2)−cos⁡(ωt+(N−12)Δβ)=2sin⁡(NΔβ2)sin⁡(ωt+(N−1)Δβ2)\cos\left(\omega t - \frac{\Delta \beta}{2}\right) - \cos\left(\omega t + \left(N - \frac{1}{2}\right) \Delta \beta\right) = 2 \sin\left(\frac{N \Delta \beta}{2}\right) \sin\left(\omega t + \frac{(N - 1) \Delta \beta}{2}\right)

*   Equating the expressions yields the simplified sum:

sin⁡(ωt)+sin⁡(ωt+Δβ)+⋯+sin⁡(ωt+(N−1)Δβ)=sin⁡(NΔβ2)sin⁡(Δβ2)sin⁡(ωt+(N−1)Δβ2)\sin(\omega t) + \sin(\omega t + \Delta \beta) + \dots + \sin(\omega t + (N - 1) \Delta \beta) = \frac{\sin\left(\frac{N \Delta \beta}{2}\right)}{\sin\left(\frac{\Delta \beta}{2}\right)} \sin\left(\omega t + \frac{(N - 1) \Delta \beta}{2}\right)

*   Thus, the total instantaneous electric field equation is:

E=E10[sin⁡(NΔβ2)sin⁡(Δβ2)]sin⁡(ωt+(N−1)Δβ2)E = E_{10} \left[ \frac{\sin\left(\frac{N \Delta \beta}{2}\right)}{\sin\left(\frac{\Delta \beta}{2}\right)} \right] \sin\left(\omega t + \frac{(N - 1) \Delta \beta}{2}\right)

  • Time Integration and Final Intensity Formulation:
    • The time average of a function f(t)f(t) over period TT is defined as:

⟨f(t)⟩=1T∫0Tf(t) dt\langle f(t) \rangle = \frac{1}{T} \int_0^T f(t)\,dt

*   For a harmonic wave with period T=2πωT = \frac{2 \pi}{\omega}:

1T∫0Tsin⁡2(ωt+ϕ) dt=1T∫0T1−cos⁡(2ωt+2ϕ)2 dt=12\frac{1}{T} \int_0^T \sin^2(\omega t + \phi)\,dt = \frac{1}{T} \int_0^T \frac{1 - \cos(2 \omega t + 2 \phi)}{2}\,dt = \frac{1}{2}

*   This follows because cos⁡(2ωt+2ϕ)\cos(2 \omega t + 2 \phi) oscillates symmetrically about zero over a full period.
*   Applying time averaging to the squared electric field gives:

I∝⟨E2⟩=12E102[sin⁡(NΔβ2)sin⁡(Δβ2)]2I \propto \langle E^2 \rangle = \frac{1}{2} E_{10}^2 \left[ \frac{\sin\left(\frac{N \Delta \beta}{2}\right)}{\sin\left(\frac{\Delta \beta}{2}\right)} \right]^2

*   Defining the peak central bright spot intensity as I0=12N2E102I_0 = \frac{1}{2} N^2 E_{10}^2:

I=I0[sin⁡(NΔβ2)Nsin⁡(Δβ2)]2I = I_0 \left[ \frac{\sin\left(\frac{N \Delta \beta}{2}\right)}{N \sin\left(\frac{\Delta \beta}{2}\right)} \right]^2

*   In the continuum limit where source points become infinitely close (Δβ→0\Delta \beta \rightarrow 0), apply the small-angle approximation sin⁡(Δβ2)≈Δβ2\sin\left(\frac{\Delta \beta}{2}\right) \approx \frac{\Delta \beta}{2}:

Nsin⁡(Δβ2)≈N(Δβ2)=β2N \sin\left(\frac{\Delta \beta}{2}\right) \approx N \left(\frac{\Delta \beta}{2}\right) = \frac{\beta}{2}

*   Substituting β2=πasin⁡(θ)λ\frac{\beta}{2} = \frac{\pi a \sin(\theta)}{\lambda} yields the single-slit intensity distribution:

I=I0[sin⁡(β2)β2]2=I0[sin⁡(πasin⁡(θ)λ)πasin⁡(θ)λ]2I = I_0 \left[ \frac{\sin\left(\frac{\beta}{2}\right)}{\frac{\beta}{2}} \right]^2 = I_0 \left[ \frac{\sin\left(\frac{\pi a \sin(\theta)}{\lambda}\right)}{\frac{\pi a \sin(\theta)}{\lambda}} \right]^2

*   *Sinc Function Definition:* In optics and engineering literature, the function sin⁡(x)x\frac{\sin(x)}{x} is referred to as the "sinc" function.

Theoretical Derivation of Double-Slit Interference Intensity

  • Superposition and Interference Dynamics:
    • The total instantaneous electric field from two slits is:

E=E1+E2\mathbf{E} = \mathbf{E}_1 + \mathbf{E}_2

*   The Poynting vector magnitude SS is proportional to field squared:

S∝E2=E12+E22+2E1⋅E2S \propto \mathbf{E}^2 = E_1^2 + E_2^2 + 2 \mathbf{E}_1 \cdot \mathbf{E}_2

*   Taking the time average yields intensity:

I=⟨S⟩∝⟨E12⟩+⟨E22⟩+2⟨E1⋅E2⟩I = \langle S \rangle \propto \langle E_1^2 \rangle + \langle E_2^2 \rangle + 2 \langle \mathbf{E}_1 \cdot \mathbf{E}_2 \rangle

*   The cross term 2⟨E1⋅E2⟩2 \langle \mathbf{E}_1 \cdot \mathbf{E}_2 \rangle represents the phase correlation between waves.
*   *Incoherent Sources:* Cross term vanishes due to random phase variations, yielding Iincoherent=I1+I2I_{\text{incoherent}} = I_1 + I_2
*   *Coherent Constructive Interference:* When E1=E2\mathbf{E}_1 = \mathbf{E}_2, intensity quadruples:

I=4I1I = 4 I_1

*   *Coherent Destructive Interference:* When E1=−E2\mathbf{E}_1 = -\mathbf{E}_2, intensity drops to zero:

I=0I = 0

  • Derivation for Coherent Sinusoidal Plane Waves:
    • Let the equal-amplitude electric field components from slit 1 and slit 2 at origin point PP be:

E1=E0sin⁡(ωt)E_1 = E_0 \sin(\omega t)

E2=E0sin⁡(ωt+ϕ)E_2 = E_0 \sin(\omega t + \phi)

*   Using the sum identity sin⁡(α)+sin⁡(β)=2sin⁡(α+β2)cos⁡(α−β2)\sin(\alpha) + \sin(\beta) = 2 \sin\left(\frac{\alpha + \beta}{2}\right) \cos\left(\frac{\alpha - \beta}{2}\right), superposition yields:

E=E1+E2=2E0cos⁡(ϕ2)sin⁡(ωt+ϕ2)E = E_1 + E_2 = 2 E_0 \cos\left(\frac{\phi}{2}\right) \sin\left(\omega t + \frac{\phi}{2}\right)

*   Calculating time-averaged intensity:

I∝⟨E2⟩=4E02cos⁡2(ϕ2)⟨sin⁡2(ωt+ϕ2)⟩=2E02cos⁡2(ϕ2)I \propto \langle E^2 \rangle = 4 E_0^2 \cos^2\left(\frac{\phi}{2}\right) \left\langle \sin^2\left(\omega t + \frac{\phi}{2}\right) \right\rangle = 2 E_0^2 \cos^2\left(\frac{\phi}{2}\right)

*   Expressed in terms of peak intensity I0I_0:

I=I0cos⁡2(ϕ2)I = I_0 \cos^2\left(\frac{\phi}{2}\right)

  • Phase Difference and Geometry Conversion:
    • Path difference δ=dsin⁡(θ)\delta = d \sin(\theta) relates to phase shift ϕ\phi via:

δλ=ϕ2π  ⟹  ϕ=2πδλ=2πdsin⁡(θ)λ\frac{\delta}{\lambda} = \frac{\phi}{2 \pi} \implies \phi = \frac{2 \pi \delta}{\lambda} = \frac{2 \pi d \sin(\theta)}{\lambda}

*   Substituting ϕ\phi yields the double-slit interference intensity equation:

I=I0cos⁡2(πdsin⁡(θ)λ)I = I_0 \cos^2\left(\frac{\pi d \sin(\theta)}{\lambda}\right)

*   Using small-angle approximation sin⁡(θ)≈tan⁡(θ)=yL\sin(\theta) \approx \tan(\theta) = \frac{y}{L}:

I=I0cos⁡2(πdyλL)I = I_0 \cos^2\left(\frac{\pi d y}{\lambda L}\right)

Total Composite Double-Slit Diffraction and Interference Pattern

  • Combined Function Equation:
    • For slits of finite width aa separated by center-to-center distance dd, the total intensity pattern is the product of single-slit diffraction and double-slit interference factors.
    • Single-slit diffraction factor:

Isingle=I0[sin⁡(πasin⁡(θ)λ)πasin⁡(θ)λ]2I_{\text{single}} = I_0 \left[ \frac{\sin\left(\frac{\pi a \sin(\theta)}{\lambda}\right)}{\frac{\pi a \sin(\theta)}{\lambda}} \right]^2

*   Double-slit interference factor:

Idouble=I0cos⁡2(πdsin⁡(θ)λ)I_{\text{double}} = I_0 \cos^2\left(\frac{\pi d \sin(\theta)}{\lambda}\right)

*   Total composite double-slit intensity distribution equation:

I=I0cos⁡2(πdsin⁡(θ)λ)[sin⁡(πasin⁡(θ)λ)πasin⁡(θ)λ]2I = I_0 \cos^2\left(\frac{\pi d \sin(\theta)}{\lambda}\right) \left[ \frac{\sin\left(\frac{\pi a \sin(\theta)}{\lambda}\right)}{\frac{\pi a \sin(\theta)}{\lambda}} \right]^2

  • Physical Roles of Terms:
    • Interference Factor cos⁡2(πdsin⁡(θ)λ)\cos^2\left(\frac{\pi d \sin(\theta)}{\lambda}\right): Produces the closely spaced interference fringes/substructure.
    • Diffraction Factor [sin⁡(πasin⁡(θ)λ)πasin⁡(θ)λ]2\left[ \frac{\sin\left(\frac{\pi a \sin(\theta)}{\lambda}\right)}{\frac{\pi a \sin(\theta)}{\lambda}} \right]^2: Acts as a broad overarching envelope that bounds and modulates the maximum amplitude and number of observable interference peaks.