Sinusoidal Inputs and Half-Wave Rectification Study Guide

Fundamental Principles of Half-Wave Rectification and Diode Models

  • Half-Wave Rectification Definition and Purpose:

    • Rectification is the process of converting an alternating current (AC) voltage or current, which periodically reverses direction, into a unidirectional direct current (DC) signal.
    • A half-wave rectifier utilizes the unidirectional conduction property of a diode to permit current flow during only one half-cycle of the input sinusoid, blocking or clipping the alternate half-cycle.
  • Mathematical Characterization of AC and DC Values:

    • Sinusoidal AC Input:
    • vi(t)=Vmsin⁡(ωt)=Vmsin⁡(2πft)v_i(t) = V_m \sin(\omega t) = V_m \sin(2\pi f t)
    • Peak amplitude is denoted by VmV_m.
    • Angular frequency is ω=2πf\omega = 2\pi f, where ff is the frequency in Hertz (Hz\text{Hz}).
    • Period of oscillation: T=1fT = \frac{1}{f}.
    • DC (Average) Value of a Rectified Waveform:
    • The general definition of the DC or average value of any periodic waveform v(t)v(t) with period TT is:       Vdc=1T∫0Tv(t) dtV_{\text{dc}} = \frac{1}{T} \int_{0}^{T} v(t)\,dt
    • For an ideal half-wave rectifier conducting over the interval 0≤t≤T20 \le t \le \frac{T}{2} with peak value VmV_m:       Vdc=1T∫0T/2Vmsin⁡(ωt) dt=Vmπ≈0.318×VmV_{\text{dc}} = \frac{1}{T} \int_{0}^{T/2} V_m \sin(\omega t)\,dt = \frac{V_m}{\pi} \approx 0.318 \times V_m
    • When accounting for diode knee/offset voltage (VKV_K or VTV_T):       Vdc≈0.318×(Vm−VK)V_{\text{dc}} \approx 0.318 \times (V_m - V_K)
  • Diode Equivalent Models:

    • Ideal Diode Model:
    • Forward-biased state (vD≥0v_D \ge 0\,V\text{V}): acts as a closed switch or short circuit with zero forward voltage drop (VD=0V_D = 0\,V\text{V}) and zero forward resistance (ron=0r_{\text{on}} = 0\,Ω\Omega).
    • Reverse-biased state (vD<0v_D < 0\,V\text{V}): acts as an open switch or open circuit (iD=0i_D = 0\,A\text{A}).
    • Approximate Equivalent Model (Silicon Diode):
    • Forward conduction occurs once the anode-to-cathode voltage overcomes the barrier potential (firing knee voltage VK=0.7V_K = 0.7\,V\text{V}).
    • Modeled during conduction as a constant DC voltage drop: VD=0.7V_D = 0.7\,V\text{V}.
    • Reverse-biased state remains an open circuit (iD=0i_D = 0\,A\text{A}) until the breakdown limit is reached.
  • Maximum Power and Current Ratings:

    • The power dissipated by a semiconductor diode during conduction under the approximate model is defined by:     PD=VD×IDP_D = V_D \times I_D
    • Given a maximum rated power dissipation PmaxP_{\text{max}}, the maximum allowable continuous forward current is:     Imax=PmaxVDI_{\text{max}} = \frac{P_{\text{max}}}{V_D}

Schematic diagrams for half-wave rectifier and diode networks (Figs. 2.168 - 2.172)

Problem 22: Ideal Diode Half-Wave Rectifier Analysis

  • Circuit Topology and Parameters (Fig. 2.168):

    • Input voltage: Sinusoidal waveform viv_i with frequency f=60f = 60\,Hz\text{Hz}.
    • Diode: Ideal (VK=0V_K = 0\,V\text{V}), oriented with anode connected to the input source viv_i and cathode connected to the load.
    • Load resistance: R=2R = 2\,kΩ\text{k}\Omega.
    • Measured average output level: Vdc=2V_{\text{dc}} = 2\,V\text{V}.
  • Derivation of the Peak Input Voltage (VmV_m):

    • For an ideal half-wave rectifier:     Vdc=Vmπ=0.318×VmV_{\text{dc}} = \frac{V_m}{\pi} = 0.318 \times V_m
    • Rearranging for VmV_m:     Vm=Vdc0.318=2 V0.318≈6.28 VV_m = \frac{V_{\text{dc}}}{0.318} = \frac{2\,\text{V}}{0.318} \approx 6.28\,\text{V}
    • Using the exact fractional formulation:     Vm=2 V×π≈6.283 VV_m = 2\,\text{V} \times \pi \approx 6.283\,\text{V}
  • Waveform Behavioral Characteristics:

    • Period of the Signal:T=1f=160 Hz≈16.67 msT = \frac{1}{f} = \frac{1}{60\,\text{Hz}} \approx 16.67\,\text{ms}
    • Positive half-cycle interval: 0≤t≤T2=8.330 \le t \le \frac{T}{2} = 8.33\,ms\text{ms}.
    • Negative half-cycle interval: T2≤t≤T=16.67\frac{T}{2} \le t \le T = 16.67\,ms\text{ms}.
    • Input Voltage (viv_i):
    • Alternates continuously between a positive peak of +6.28+6.28\,V\text{V} and a negative peak of −6.28-6.28\,V\text{V}.
    • Diode Voltage (vdv_d):
    • During the positive half-cycle (vi>0v_i > 0\,V\text{V}), the diode is forward-biased and acts as a short circuit: vd=0v_d = 0\,V\text{V}.
    • During the negative half-cycle (vi<0v_i < 0\,V\text{V}), the diode is reverse-biased (open circuit), carrying zero current. By Kirchhoff's Voltage Law (KVL), the entire negative input voltage drops across the open diode: vd=viv_d = v_i.
    • Peak inverse voltage across the diode: PIV=Vm=6.28\text{PIV} = V_m = 6.28\,V\text{V}.
    • Diode Current (idi_d):
    • Conduction occurs during the positive half-cycle:       id(t)=vi(t)R=vi(t)2 kΩi_d(t) = \frac{v_i(t)}{R} = \frac{v_i(t)}{2\,\text{k}\Omega}
    • Peak diode current:       Id,peak=VmR=6.28 V2 kΩ=3.14 mAI_{d,\text{peak}} = \frac{V_m}{R} = \frac{6.28\,\text{V}}{2\,\text{k}\Omega} = 3.14\,\text{mA}
    • During the negative half-cycle (T2≤t≤T\frac{T}{2} \le t \le T):       id(t)=0 mAi_d(t) = 0\,\text{mA}

Problem 23: Half-Wave Rectifier with Silicon Diode Model

  • Circuit Topology and Parameters:

    • The configuration of Fig. 2.168 is analyzed with a practical silicon diode replacement.
    • Knee/firing threshold voltage: VK=0.7V_K = 0.7\,V\text{V}.
    • Load resistance: R=2R = 2\,kΩ\text{k}\Omega.
    • Frequency: f=60f = 60\,Hz\text{Hz}.
    • Given output DC level: Vdc=2V_{\text{dc}} = 2\,V\text{V}.
  • Determination of Required Input Peak Voltage (VmV_m):

    • For a silicon diode, output voltage conduction begins only after vi(t)v_i(t) exceeds 0.70.7\,V\text{V}.
    • Peak output voltage across the load resistor is:     Vo,peak=Vm−VK=Vm−0.7 VV_{o,\text{peak}} = V_m - V_K = V_m - 0.7\,\text{V}
    • Average DC output equation:     Vdc=0.318×(Vm−0.7 V)V_{\text{dc}} = 0.318 \times (V_m - 0.7\,\text{V})
    • Substituting Vdc=2V_{\text{dc}} = 2\,V\text{V}:     2 V=0.318×(Vm−0.7 V)2\,\text{V} = 0.318 \times (V_m - 0.7\,\text{V})Vm−0.7 V=2 V0.318≈6.28 VV_m - 0.7\,\text{V} = \frac{2\,\text{V}}{0.318} \approx 6.28\,\text{V}Vm=6.28 V+0.7 V=6.98 VV_m = 6.28\,\text{V} + 0.7\,\text{V} = 6.98\,\text{V}
  • Waveform Behavioral Characteristics:

    • Input Voltage (viv_i):
    • Sinusoidal waveform having a peak amplitude of Vm=6.98V_m = 6.98\,V\text{V} and minimum peak of −6.98-6.98\,V\text{V}.
    • Diode Voltage (vdv_d):
    • When vi≥0.7v_i \ge 0.7\,V\text{V}, the diode is conducting in the forward active region: vd=0.7v_d = 0.7\,V\text{V}.
    • When vi<0.7v_i < 0.7\,V\text{V}, the diode is OFF (non-conducting), so id=0i_d = 0\,A\text{A}, and the load voltage is zero. Thus, by KVL: vd=viv_d = v_i.
    • Extreme negative value: vd=−6.98v_d = -6.98\,V\text{V} at the negative peak of the AC input.
    • Diode Current (idi_d):
    • Forward conduction occurs over the interval where vi(t)>0.7v_i(t) > 0.7\,V\text{V}.
    • Conduction angle is slightly less than 180∘180^{\circ} due to the threshold delay.
    • Maximum peak diode current:       Id,peak=Vm−0.7 VR=6.98 V−0.7 V2 kΩ=6.28 V2 kΩ=3.14 mAI_{d,\text{peak}} = \frac{V_m - 0.7\,\text{V}}{R} = \frac{6.98\,\text{V} - 0.7\,\text{V}}{2\,\text{k}\Omega} = \frac{6.28\,\text{V}}{2\,\text{k}\Omega} = 3.14\,\text{mA}

Problem 24: Half-Wave Rectifier Loaded with an Additional Parallel Branch

  • Circuit Topology and Parameters (Fig. 2.169):

    • AC source with ideal diode connected in series.
    • Original resistor: R1=2R_1 = 2\,kΩ\text{k}\Omega.
    • Added parallel load resistor: RL=10R_L = 10\,kΩ\text{k}\Omega.
    • Frequency: f=60f = 60\,Hz\text{Hz}.
    • Peak input voltage: Vm=6.28V_m = 6.28\,V\text{V} (derived from Problem 22 where Vdc=2V_{\text{dc}} = 2\,V\text{V}).
  • Equivalent Resistance and Output Voltage Analysis:

    • The total load seen by the diode during conduction is the parallel combination of the two resistive branches:     Req=R1∥RL=R1×RLR1+RLR_{\text{eq}} = R_1 \parallel R_L = \frac{R_1 \times R_L}{R_1 + R_L}Req=2 kΩ×10 kΩ2 kΩ+10 kΩ=2012 kΩ=53 kΩ≈1.67 kΩR_{\text{eq}} = \frac{2\,\text{k}\Omega \times 10\,\text{k}\Omega}{2\,\text{k}\Omega + 10\,\text{k}\Omega} = \frac{20}{12}\,\text{k}\Omega = \frac{5}{3}\,\text{k}\Omega \approx 1.67\,\text{k}\Omega
    • Because an ideal diode has zero internal source impedance when forward biased, the load voltage vLv_L is connected directly across viv_i during the positive half-cycle:     vL(t)=vi(t)for vi(t)>0v_L(t) = v_i(t) \quad \text{for } v_i(t) > 0vL(t)=0 Vfor vi(t)≤0v_L(t) = 0\,\text{V} \quad \text{for } v_i(t) \le 0
    • Peak load voltage remains unchanged:     VL,peak=Vm=6.28 VV_{L,\text{peak}} = V_m = 6.28\,\text{V}
    • Average DC load voltage remains:     Vdc=0.318×6.28 V=2.0 VV_{\text{dc}} = 0.318 \times 6.28\,\text{V} = 2.0\,\text{V}
  • Load Current (iLi_L) and Diode Current (idi_d):

    • Load current through the 1010\,kΩ\text{k}\Omega resistor during positive half-cycle conduction:     iL(t)=vL(t)RL=vi(t)10 kΩi_L(t) = \frac{v_L(t)}{R_L} = \frac{v_i(t)}{10\,\text{k}\Omega}
    • Peak load current:     IL,peak=VL,peakRL=6.28 V10 kΩ=0.628 mAI_{L,\text{peak}} = \frac{V_{L,\text{peak}}}{R_L} = \frac{6.28\,\text{V}}{10\,\text{k}\Omega} = 0.628\,\text{mA}
    • Peak current through the parallel 22\,kΩ\text{k}\Omega resistor branch:     I1,peak=6.28 V2 kΩ=3.14 mAI_{1,\text{peak}} = \frac{6.28\,\text{V}}{2\,\text{k}\Omega} = 3.14\,\text{mA}
    • Total peak diode current delivering charge to both branches:     Id,peak=I1,peak+IL,peak=3.14 mA+0.628 mA=3.768 mAI_{d,\text{peak}} = I_{1,\text{peak}} + I_{L,\text{peak}} = 3.14\,\text{mA} + 0.628\,\text{mA} = 3.768\,\text{mA}
    • Cross-verification via equivalent resistance:       Id,peak=VmReq=6.28 V1.667 kΩ≈3.768 mAI_{d,\text{peak}} = \frac{V_m}{R_{\text{eq}}} = \frac{6.28\,\text{V}}{1.667\,\text{k}\Omega} \approx 3.768\,\text{mA}

Problem 25: Shunt Half-Wave Rectifier / Clipper Circuit

  • Circuit Topology and Parameters (Fig. 2.170):

    • Input voltage rating: Vi=120V_i = 120\,V (rms)\text{V (rms)}.
    • Series resistor: R=2R = 2\,kΩ\text{k}\Omega.
    • Diode: Ideal diode connected in shunt across the output terminals, oriented with its cathode pointing upward toward the top terminal and anode connected to ground.
    • Output: Taken directly across the parallel diode branch (vov_o).
  • Input Amplitude Calculations:

    • Peak voltage from RMS specification:     Vm=2×Vrms=2×120 V≈1.4142×120 V≈169.7 VV_m = \sqrt{2} \times V_{\text{rms}} = \sqrt{2} \times 120\,\text{V} \approx 1.4142 \times 120\,\text{V} \approx 169.7\,\text{V}
  • Circuit State Analysis and Output Waveform (vov_o):

    • Positive Half-Cycle (vi>0v_i > 0\,V\text{V}):
    • The positive input potential makes the cathode positive relative to the anode (ground).
    • The ideal diode is reverse-biased, presenting an open circuit.
    • With no external load connected across the output terminals, the output current is zero (io=0i_o = 0\,A\text{A}).
    • Voltage drop across the series 22\,kΩ\text{k}\Omega resistor is VR=0V_R = 0\,V\text{V}.
    • Therefore, the output tracks the input voltage perfectly:       vo(t)=vi(t)v_o(t) = v_i(t)
    • Peak output voltage during this interval:       Vo,peak=+169.7 VV_{o,\text{peak}} = +169.7\,\text{V}
    • Negative Half-Cycle (vi<0v_i < 0\,V\text{V}):
    • The negative potential at the top rail places the cathode at a negative potential relative to the anode (ground).
    • The diode is forward-biased, acting as an ideal short circuit to ground.
    • The output voltage is held at ground potential:       vo(t)=0 Vv_o(t) = 0\,\text{V}
    • The entire source voltage drops across the series 22\,kΩ\text{k}\Omega resistor during this interval.
  • Determination of Average DC Voltage (VdcV_{\text{dc}}):

    • Because the waveform is clipped to 00\,V\text{V} for the entire negative half-cycle and reproduces the positive half-cycle unaltered, it forms a standard positive half-wave rectified waveform:     Vdc=0.318×VmV_{\text{dc}} = 0.318 \times V_mVdc=0.318×169.7 V≈53.96 VV_{\text{dc}} = 0.318 \times 169.7\,\text{V} \approx 53.96\,\text{V}
    • Expressed using the exact factor Vmπ\frac{V_m}{\pi}:     Vdc=169.7 Vπ≈54.02 VV_{\text{dc}} = \frac{169.7\,\text{V}}{\pi} \approx 54.02\,\text{V}

Problem 26: Series-Parallel Waveform Clipper and Current Response

  • Circuit Topology and Parameters (Fig. 2.171):

    • Input voltage: Alternating sinusoidal signal with positive peak of +10+10\,V\text{V} and negative peak of −10-10\,V\text{V} (Vm=10V_m = 10\,V\text{V}).
    • Series resistor: R1=1R_1 = 1\,kΩ\text{k}\Omega, carrying current iRi_R.
    • Shunt branch: A silicon diode (Si, VK=0.7V_K = 0.7\,V\text{V}) oriented pointing downward (anode at top, cathode at ground) in parallel with a load resistor R2=1R_2 = 1\,kΩ\text{k}\Omega.
    • Output vov_o: Measured across the parallel diode-resistor network.
  • Circuit Conduction Regimes:

    • State 1: Diode Non-Conducting (OFF):
    • When the diode is OFF, the network acts as a linear voltage divider between R1R_1 and R2R_2:       vo(t)=vi(t)×(R2R1+R2)=vi(t)×(1 kΩ1 kΩ+1 kΩ)=0.5×vi(t)v_o(t) = v_i(t) \times \left( \frac{R_2}{R_1 + R_2} \right) = v_i(t) \times \left( \frac{1\,\text{k}\Omega}{1\,\text{k}\Omega + 1\,\text{k}\Omega} \right) = 0.5 \times v_i(t)
    • The silicon diode turns ON only when its anode-to-cathode voltage reaches 0.70.7\,V\text{V}, which requires:       vo(t)=0.5×vi(t)≥0.7 V  ⟹  vi(t)≥1.4 Vv_o(t) = 0.5 \times v_i(t) \ge 0.7\,\text{V} \implies v_i(t) \ge 1.4\,\text{V}
    • State 2: Diode Conducting (ON) during Positive Half-Cycle (vi(t)≥1.4v_i(t) \ge 1.4\,V\text{V}):
    • The silicon diode enters forward conduction, clamping the output node to its knee voltage:       vo(t)=0.7 Vv_o(t) = 0.7\,\text{V}
    • The excess voltage above 0.70.7\,V\text{V} drops across the series resistor R1R_1:       iR(t)=vi(t)−0.7 VR1=vi(t)−0.7 V1 kΩi_R(t) = \frac{v_i(t) - 0.7\,\text{V}}{R_1} = \frac{v_i(t) - 0.7\,\text{V}}{1\,\text{k}\Omega}
    • At the positive peak of input (vi=+10v_i = +10\,V\text{V}):       vo,peak=0.7 Vv_{o,\text{peak}} = 0.7\,\text{V}iR,peak=10 V−0.7 V1 kΩ=9.3 V1 kΩ=9.3 mAi_{R,\text{peak}} = \frac{10\,\text{V} - 0.7\,\text{V}}{1\,\text{k}\Omega} = \frac{9.3\,\text{V}}{1\,\text{k}\Omega} = 9.3\,\text{mA}
    • State 3: Diode OFF during Sub-threshold and Negative Inputs (vi(t)<1.4v_i(t) < 1.4\,V\text{V}):
    • Throughout the negative half-cycle (vi≤0v_i \le 0\,V\text{V}) and the small positive interval below 1.41.4\,V\text{V}, the diode is reverse-biased or non-conducting.
    • The output continues to scale by the voltage divider factor of 0.50.5:       vo(t)=0.5×vi(t)v_o(t) = 0.5 \times v_i(t)
    • At the negative peak of input (vi=−10v_i = -10\,V\text{V}):       vo,neg peak=0.5×(−10 V)=−5 Vv_{o,\text{neg peak}} = 0.5 \times (-10\,\text{V}) = -5\,\text{V}
    • Current through R1R_1 flows in the reverse direction:       iR(t)=vi(t)R1+R2=vi(t)2 kΩi_R(t) = \frac{v_i(t)}{R_1 + R_2} = \frac{v_i(t)}{2\,\text{k}\Omega}
    • At the negative peak (vi=−10v_i = -10\,V\text{V}):       iR,neg peak=−10 V2 kΩ=−5 mAi_{R,\text{neg peak}} = \frac{-10\,\text{V}}{2\,\text{k}\Omega} = -5\,\text{mA}
  • Summary of Sketched Waveform Extrema:

    • Output voltage (vov_o):
    • Maximum upper limit: Clamped flat at +0.7+0.7\,V\text{V}.
    • Minimum lower limit: Reaches −5-5\,V\text{V} at the negative crest.
    • Series resistor current (iRi_R):
    • Maximum positive value: +9.3+9.3\,mA\text{mA}.
    • Minimum negative value: −5.0-5.0\,mA\text{mA}.

Problem 27: Maximum Power Dissipation, Parallel Diodes, and Overload Failure Analysis

  • Circuit Topology and Parameters (Fig. 2.172):

    • Input voltage: Sinusoidal AC wave with peak amplitude Vimax=160V_{i_{\text{max}}} = 160\,V\text{V}.
    • Diode network: Two identical silicon diodes connected in parallel, both pointing rightward toward the load.
    • Load network: Two parallel load resistors:
    • Branch 1: R1=4.7R_1 = 4.7\,kΩ\text{k}\Omega
    • Branch 2: R2=68R_2 = 68\,kΩ\text{k}\Omega
    • Rating per diode: Maximum power dissipation rating Pmax=14P_{\text{max}} = 14\,mW\text{mW}.
    • Diode model: Approximate equivalent model with forward knee voltage VD=0.7V_D = 0.7\,V\text{V}.
  • Part (a): Maximum Current Rating of Each Diode:

    • Power dissipation relation for the constant-voltage diode model:     Pmax=VD×ID,maxP_{\text{max}} = V_D \times I_{D,\text{max}}
    • Solving for the rated maximum current ID,maxI_{D,\text{max}}:     ID,max=PmaxVD=14 mW0.7 V=14×10−3 W0.7 V=20 mAI_{D,\text{max}} = \frac{P_{\text{max}}}{V_D} = \frac{14\,\text{mW}}{0.7\,\text{V}} = \frac{14 \times 10^{-3}\,\text{W}}{0.7\,\text{V}} = 20\,\text{mA}
    • Each individual diode can safely conduct a maximum forward continuous current of 2020\,mA\text{mA}.
  • Part (b): Maximum Permissible Current (ImaxI_{\text{max}}) for Parallel Diode Pair:

    • In a parallel arrangement, the total current capacity is the sum of the capacities of the individual matched diodes:     Imax=ID1,max+ID2,max=20 mA+20 mA=40 mAI_{\text{max}} = I_{D1,\text{max}} + I_{D2,\text{max}} = 20\,\text{mA} + 20\,\text{mA} = 40\,\text{mA}
  • Part (c): Current Through Each Diode at Peak Voltage (VimaxV_{i_{\text{max}}}):

    • Calculate the equivalent resistance of the parallel load:     RL=R1∥R2=4.7 kΩ×68 kΩ4.7 kΩ+68 kΩ=319.672.7 kΩ≈4.396 kΩR_L = R_1 \parallel R_2 = \frac{4.7\,\text{k}\Omega \times 68\,\text{k}\Omega}{4.7\,\text{k}\Omega + 68\,\text{k}\Omega} = \frac{319.6}{72.7}\,\text{k}\Omega \approx 4.396\,\text{k}\Omega
    • Peak output voltage across the load network at Vimax=160V_{i_{\text{max}}} = 160\,V\text{V}:     Vo,peak=Vimax−VD=160 V−0.7 V=159.3 VV_{o,\text{peak}} = V_{i_{\text{max}}} - V_D = 160\,\text{V} - 0.7\,\text{V} = 159.3\,\text{V}
    • Total peak current demanded by the load network:     Itotal,peak=Vo,peakRL=159.3 V4.396 kΩ≈36.24 mAI_{\text{total,peak}} = \frac{V_{o,\text{peak}}}{R_L} = \frac{159.3\,\text{V}}{4.396\,\text{k}\Omega} \approx 36.24\,\text{mA}
    • Component check across individual branches:       IR1,peak=159.3 V4.7 kΩ≈33.894 mAI_{R1,\text{peak}} = \frac{159.3\,\text{V}}{4.7\,\text{k}\Omega} \approx 33.894\,\text{mA}IR2,peak=159.3 V68 kΩ≈2.343 mAI_{R2,\text{peak}} = \frac{159.3\,\text{V}}{68\,\text{k}\Omega} \approx 2.343\,\text{mA}Itotal,peak=33.894 mA+2.343 mA=36.237 mA≈36.24 mAI_{\text{total,peak}} = 33.894\,\text{mA} + 2.343\,\text{mA} = 36.237\,\text{mA} \approx 36.24\,\text{mA}
    • Current through each diode assuming equal distribution between identical parallel devices:     ID=Itotal,peak2=36.24 mA2=18.12 mAI_D = \frac{I_{\text{total,peak}}}{2} = \frac{36.24\,\text{mA}}{2} = 18.12\,\text{mA}
    • Verification against safe rating:
    • Actual operating current: 18.1218.12\,mA\text{mA}.
    • Allowable current threshold: 2020\,mA\text{mA}.
    • Because 18.1218.12\,mA<20\text{mA} < 20\,mA\text{mA}, both diodes operate reliably within their rated thermal boundaries.
  • Part (d): Expected Result if Only One Diode Were Present:

    • If one diode is removed, the remaining single diode must conduct the full load demand:     Isingle=Itotal,peak≈36.24 mAI_{\text{single}} = I_{\text{total,peak}} \approx 36.24\,\text{mA}
    • Comparing the operational current with the maximum rating:     36.24 mA>20 mA36.24\,\text{mA} > 20\,\text{mA}
    • The actual power dissipation of the single diode would be:     PD=VD×Isingle=0.7 V×36.24 mA≈25.37 mWP_D = V_D \times I_{\text{single}} = 0.7\,\text{V} \times 36.24\,\text{mA} \approx 25.37\,\text{mW}
    • Because 25.3725.37\,mW\text{mW} significantly exceeds the maximum power rating Pmax=14P_{\text{max}} = 14\,mW\text{mW}, the single diode will overheat due to excessive junction temperature, leading to thermal breakdown and permanent device failure (destruction/burnout).