Test Prep Block 2

1. Which of these materials is the most anodic?

A. 7075-T6 aluminum alloy

B. Magnesium

C. Cadmium

2. Which type of coating typically includes phosphoric acid as one of its components at the time of application?

A. Zinc chromate primer

B. Epoxy primer

C. Wash Primer

3. Which of the following are the desired effects of using Alodine (also known surface providing a microscopically rough surface and forms an oxide film on as Bonderite) on aluminum alloy?

1. A slightly rough surface.

2. Relieved surface stresses.

3. A smooth painting surface. anodizing in aircraft work.

4. Increased corrosion resistance.

A. 1, 2, and 4

B. 3 and 4

C. 1 and 4

4. Select the solvent used to clean acrylics and rubber:

A. Methyl ethyl ketone

B. Aromatic naphtha

C. Aliphatic naphtha

5. Of the choices provided, what type of corrosion is most likely to occur if a surface is not properly Alodized?

A. Filiform

B. Dissimilar metal

C. Stress

6. Galvanic corrosion at the interface of a dissimilar metal part may best be prevented by?

A. Placing a nonporous dielectric material between the surfaces.

B. Conducting frequent inspections and keeping all exposed areas of the part clean.

C. Sealing exposed seam edges with a recommended sealing compound.

7. Which of the following are acceptable to use in cleaning anodized surfaces?

1. Steel wool

2. Brass wire brush

3. Aluminum wool

4. Stainless steel wire brush

5. Fiber bristle brush

A. 2 & 4

B. 3 & 5

C. 1, 3, & 5

8. Which defect in aircraft finishes may be caused by adverse humidity, drafts, or sudden changes in temperature?

A. Blushing

B. Pinholes

C. Orange peel

9. What type of corrosion may attack the grain boundaries of aluminum alloys when the heat treatment process has been improperly accomplished?

A. Concentration cell

B. Intergranular

C. Fretting

10. Of the following, when and/or where is galvanic corrosion most likely to occur?

A. When an electrolyte (water) covers the surface of an aluminum skin, seeps into the cracks between lap joints, and oxygen is excluded from the area.

B. At the interface of a steel fastener and aluminum alloy inspection plate in the presence of an electrolyte.

C. In an area of unprotected metal exposed to an atmosphere containing battery fumes, exhaust gases, or industrial contaminants.

11. Which statement is true regarding paint system compatibility?

A. Acrylic nitrocellulose lacquers may be used over old nitrocellulose finishes.

B. Old wash primer coats may be overcoated directly with epoxy finishes.

C. Old type zinc chromate primer may not be used directly for touchup of bare metal surfaces.

12. Fayed surfaces cause concern in chemical cleaning because of the danger of joint:

A. Forming passive oxides

B. Corrosion by imbedded iron oxide

C. Entrapping corrosive materials

13. Aluminum-pigment in dope is used primarily to:

A. Reflect ultraviolet from the fabric

B. Aid in sealing out moisture from the fabric

C. Provide a silver color

14. Which of the listed conditions is NOT one of the requirements for corrosion to occur?

A. The presence of a passive oxide film

B. Electrical contact between an anodic area and a cathodic area

C. The presence of an electrolyte

15. Which statement about corrosion and anodic metals is correct?

1. In the corrosion process, it is the cathodic area or dissimilar cathodic material that corrodes.

2. In the Galvanic or Electro-Chemical Series for metals, the most anodic metals are those that will give up electrons most easily.

A. Only No. 2 is true

B. Both No. 1 and No. 2 are true

C. Only No. 1 is true

16. Before applying a protective coating to any unpainted clean aluminum, you should:

A. Wipe the surface with methyl-ethyl-ketone (MEK).

B. Remove any contaminants from the surface with a paper towel.

C. Avoid touching the surface with bare hands.

17. What is the class of working drawing that is the description/depiction of a single part?

A. Installation drawing

B. Assembly drawing

C. Detail drawing

19. Zone numbers on aircraft blueprints are used to:

A. Indicate different sections of the aircraft.

B. Locate parts in the aircraft.

C. Locate parts, sections, and views on large drawings.

20. In the reading of aircraft blueprints, the term "tolerance", used in association with aircraft parts or components:

A. Represents the limit of galvanic compatibility between different adjoining material types in aircraft parts.

B. Is the difference between extreme permissible dimensions that a part may have and still be acceptable.

C. Is the tightest permissible fit for proper construction and operation of mating parts.

21. What type of sections illustrate particular parts of an object?

A. Removed

B. Revolved

C. Half

22. Which statement or statements are true?

1. According to 14 CFR Part 91, repairs to an aircraft skin should have a detailed dimensional sketch included in the permanent records.

2. On occasion, a mechanic may need to make a simple sketch of a proposed repair to an aircraft, a new design, or a modification.

A. Only No. 1 is true

B. Only No. 2 is true

C. Both No. 1 and No. 2 are true

23. Which statement or statements are true?

1. A detail drawing is a description of a single part.

2. An assembly drawing is a description of an object made up of two or more parts.

A. Neither No. 1 nor No. 2 is true

B. Only No. 1 is true

C. Both No. 1 and No. 2 are true

24. What should be the first step of the procedure in sketching an aircraft wing skin repair?

A. Draw heavy guidelines

B. Lay out the repair

C. Block in the views

25. In a sectional view drawing, what sections illustrate particular parts of an object?

A. Removed

B. Revolved

C. Half

26. What is used to indicate that a surface must be machine finished?

A. Tolerances

B. Leader lines

C. Finished marks

27. (Refer to figure 34) What is the maximum diameter of the hole for the clevis pin?

A. 0.31255

B. 0.3175

C. 0.3130

28. (Refer to figure 37) The vertical distance between the top of the plate and the bottom of the lowest 15/64-inch hole is?

A. 2.367

B. 2.242

C. 2.250

29. (Refer to figure 36) The diameter of the holes in the finished object is:

A. 1/2 inch

B. 31/64 inch

C. 3/4 inch

30. (Refer to figure 34) What would be the minimum diameter of 4130 round stock required for the construction of the clevis that would produce a machined surface?

A. 55/64 inch

B. 1 inch

C. 7/8 inch

31. What type of drawing line consists of alternating long and short lines?

A. Dimension

B. Center

C. Hidden

32. A hydraulic system schematic drawing typically indicates the:

A. Specific location of the individual components within the aircraft.

B. Direction of fluid flow through the system.

C. Amount of pressure in the pressure and return lines, and in system components.

33. What is the allowable manufacturing tolerance for a bushing where the outside dimensions shown on the blueprint are: 1.0625 +.0025 -.0003?

A. .0028

B. 1.0647

C. 1.0650

34. When used in close proximity to magnetic compasses, cotter pins are made of what material?

A. Cadmium plated low carbon steel

B. Corrosion resisting steel

C. Anodized aluminum alloy

35. Alclad is a metal consisting of:

A. Aluminum alloy surface layers and a pure aluminum core.

B. Pure aluminum surface layers on an aluminum alloy core.

C. A homogeneous mixture of pure aluminum and aluminum alloy.

36. Self-locking nuts may be used on aircraft provided that:

A. The bolt and nut are safety wired.

B. The bolt and nut is not under tension.

C. The bolt or nut is not subject to rotation.

37. What aluminum alloy designations indicate that the metal has received no hardening or tempering treatment?

A. 3003-F

B. 5052-H36

C. 6061-O

38. If it is necessary to accurately measure the diameter of a hole approximately 1/4 inch in diameter, the mechanic should use a:

A. Telescoping gauge and determine the size of the hole by taking a micrometer reading of the adjustable end.

B. 0 to 1 inch inside micrometer and read the measurement directly.

C. Small hole gauge and determine the size of the hole by taking a micrometer reading of the ball end.

39. (Refer to figure 47) What is the measurement reading on the vernier caliper scale?

A. 1.700 inches

B. 1.437 inches

C. 1.411 inches

40. A limitation of the Barcol hardness tester is that:

A. It is a piece of fixed equipment that cannot be easily moved.

B. It cannot differentiate hardness of typical aircraft aluminum alloys.

C. It should not normally be used on aircraft steels.

41. Why is a plastic surface flushed with fresh water before it is cleaned with soap water?

A. To prevent crazing

B. To prevent discoloration

C. To prevent scratching

42. Unless otherwise specified or required, aircraft bolts should be installed so that the bolthead is:

A. Downward, or in a forward direction

B. Upward, or in a rearward direction

C. Upward, or in a forward direction

43. The primary alloying agent of 2024-T3 is indicated by:

A. 20

B. 24

C. 2

44. Which of the following occurs when a mechanical force is repeatedly applied to most metals at room temperature, such as rolling, hammering, or bending?

A. The metals become stress corrosion cracked.

B. The metals become artificially aged and become cold worked, strain or work hardened.

C. The metals become cold worked, strain or work hardened but not artificially aged.

45. Which tool is used to measure the clearance between a surface plate and a relatively narrow surface being checked for flatness?

A. Dial indicator

B. Depth gauge

C. Thickness gauge

46. How is a clevis bolt used with a fork end cable terminal secured?

A. With a castle nut tightened until slight binding occurs.

B. With a shear nut and cotter pin or a thin self locking nut tightened enough to prevent rotation.

C. With a shear nut tightened to a snug fit, but with no strain imposed on the fork and safetied with a cotter pin.

47. Aircraft bolts are usually manufactured with a:

A. Class 1 fit for the threads.

B. Class 2 fit for the threads.

C. Class 3 fit for the threads.

48. When installing a castle nut and the nut castellation does not align with the cotter pin hole in the bolt within the torque range, the acceptable practice is to:

A. Back the nut off and align to the nearest hole.

B. Continue tightening to next hole.

C. Change nut or washer and try again.

49. (Refer to figure 42) Which of the bolthead code markings shown identifies an AN corrosion resistant steel bolt?

A. 1

B. 2

C. 3

50. Which statement regarding aircraft bolts is correct?

A. Alloy steel bolts smaller than 1/4-inch diameter should not be used in primary structure.

B. In general, bolt grip lengths should equal the material thickness.

C. When tightening castellated nuts on drilled bolts, it is permissible to tighten up to 10 percent over recommended torque.