Physical Quantities and Measurement Techniques

Measurement Techniques and Instruments

  • Measuring Length:

    • Rulers are used to measure small distances of a few centimetres (cm\text{cm}).

    • Rulers measure to the nearest millimetre (mm\text{mm}) precision, recording lengths in either cm\text{cm} or mm\text{mm}.

    • Tape measures are utilized for measuring larger lengths on the scale of tens of centimetres (cm\text{cm}) or metres.

Ruler measuring the length of a pencil
  • Measuring Volume:

    • Measuring cylinders are designed to measure the volume of liquids in units such as cubic centimetres (cm3\text{cm}^3).

    • Liquid measurements must always be taken from the bottom of the meniscus.

    • Measuring cylinders determine the volume of irregularly shaped solids by measuring liquid displacement (the change in liquid volume before and after submerging the object):

      • Volume of irregular object=Measurement after−Measurement before\text{Volume of irregular object} = \text{Measurement after} - \text{Measurement before}

      • For example, if the initial liquid volume is 24 cm324\,\text{cm}^3 and the volume after submerging an irregular solid is 31 cm331\,\text{cm}^3:

        • Volume of irregular object=31 cm3−24 cm3=7 cm3\text{Volume of irregular object} = 31\,\text{cm}^3 - 24\,\text{cm}^3 = 7\,\text{cm}^3

Measuring cylinder meniscus reading and measuring irregular volume
  • Measuring Time:

    • Clocks are used to measure long time intervals.

    • Digital timers, such as stopwatches, measure short time intervals.

    • Human reaction time is a critical factor influencing short time measurements.

    • The standard human reaction time for an alert individual is approximately 0.2 s0.2\,\text{s} to 0.3 s0.3\,\text{s}, which introduces significant percentage uncertainty into very short timing measurements.

  • Worked Example — Calculating Lap Time from Stopwatch Readings:

    • Problem: A stopwatch records the time for a runner completing a 400 m400\,\text{m} track lap. The stopwatch displays time in the format minutes:seconds:hundredths of a second\text{minutes}:\text{seconds}:\text{hundredths of a second} (min:s:1/100s\text{min}:\text{s}:1/100\text{s}). Calculate the time taken to complete the lap in seconds.

    • Step 1: Identify start time from stopwatch: 0:55:10→55.10 s0:55:10 \rightarrow 55.10\,\text{s}

    • Step 2: Identify finish time from stopwatch: 1:45:10→1 min and 45.10 s1:45:10 \rightarrow 1\,\text{min}\text{ and }45.10\,\text{s}

    • Step 3: Convert finish time entirely to seconds (1 min=60 s1\,\text{min} = 60\,\text{s}):

      • Finish time=60 s+45.10 s=105.10 s\text{Finish time} = 60\,\text{s} + 45.10\,\text{s} = 105.10\,\text{s}

    • Step 4: Calculate total time elapsed:

      • Total time=Finish time−Start time\text{Total time} = \text{Finish time} - \text{Start time}

      • Total time=105.10 s−55.10 s=50 s\text{Total time} = 105.10\,\text{s} - 55.10\,\text{s} = 50\,\text{s}

    • Exam Tip: Information provided in questions may not always be needed for calculations. The track length (400 m400\,\text{m}) was irrelevant to the calculation of time elapsed.

Stopwatch displaying start time and end time for a lap

Improving Accuracy and Multiple Readings

  • Principles of Multiple Readings:

    • Taking multiple readings of a measurement reduces the impact of experimental and measurement errors, improves precision, and minimizes overall uncertainty.

    • When a single quantity is too small to measure accurately directly (e.g., thickness of a single sheet of paper), measuring a large multiple of that quantity significantly reduces measurement uncertainty.

  • Measuring Paper Thickness:

    • Measuring the thickness of one sheet of paper directly incurs a large percentage uncertainty.

    • A stack of 100100 identical sheets is measured instead using a ruler.

    • Thickness of one sheet=Thickness of stackNumber of sheets\text{Thickness of one sheet} = \frac{\text{Thickness of stack}}{\text{Number of sheets}}

    • Example calculation: If a stack of 100100 sheets measures 23 mm23\,\text{mm}:

      • Thickness of one sheet=23 mm100=0.23 mm\text{Thickness of one sheet} = \frac{23\,\text{mm}}{100} = 0.23\,\text{mm}

  • Measuring Pendulum Oscillations:

    • Measuring a single time period (one full oscillation) of a simple pendulum introduces reaction time errors at both the start and stop of timing.

    • Because a single time period is brief, human reaction time (0.2 s−0.3 s0.2\,\text{s} - 0.3\,\text{s}) produces a high percentage uncertainty.

    • To reduce uncertainty, the total time for 1010 full oscillations (swings) is measured instead.

    • Time for 1 oscillation=Time taken for 10 oscillationsNumber of oscillations\text{Time for } 1 \text{ oscillation} = \frac{\text{Time taken for } 10 \text{ oscillations}}{\text{Number of oscillations}}

    • Example calculation: If the time for 1010 swings is 15 s15\,\text{s}:

      • Time for 1 swing=15 s10=1.5 s\text{Time for } 1 \text{ swing} = \frac{15\,\text{s}}{10} = 1.5\,\text{s}

    • A reference marker (a visible line or dot placed at the equilibrium position of the oscillating pendulum) provides a clear point to start and stop the timer, further reducing reaction time timing errors.

Methods for measuring multiple readings including paper thickness stack and simple pendulum oscillations
  • Worked Example — Measuring Ball Bearing Diameter:

    • Problem: Four identical ball bearings are placed in a row touching each other between two wooden blocks on a ruler calibrated in centimetres. The inner edge of the left block aligns with 4 cm4\,\text{cm} and the inner edge of the right block aligns with 12 cm12\,\text{cm}. Calculate the diameter of one ball bearing.

    • Step 1: Determine the total length of all 4 ball bearings combined:

      • Total length=12 cm−4 cm=8 cm\text{Total length} = 12\,\text{cm} - 4\,\text{cm} = 8\,\text{cm}

    • Step 2: Divide total length by the number of ball bearings:

      • Diameter=Total lengthNumber of ball bearings\text{Diameter} = \frac{\text{Total length}}{\text{Number of ball bearings}}

      • Diameter=8 cm4=2 cm\text{Diameter} = \frac{8\,\text{cm}}{4} = 2\,\text{cm}

Four ball bearings between two wooden blocks aligned with a ruler

Scalars and Vectors

  • Fundamental Definitions (Extended Tier Only):

    • Physical quantities are classified into scalar quantities or vector quantities.

    • Scalar Quantity: A physical quantity that possesses magnitude (size) only, without any direction.

    • Vector Quantity: A physical quantity that possesses both magnitude (size) and a specified direction.

  • Distance vs. Displacement:

    • Distance: The total length of the path taken by an object, regardless of the direction of travel. Distance is a scalar quantity.

    • Displacement: The straight-line distance measured from a starting point to an ending point in a specific stated direction. Displacement is a vector quantity.

  • Speed vs. Velocity:

    • Speed: The distance travelled by an object per unit time, regardless of direction. Speed is a scalar quantity.

    • Velocity: The speed of an object in a specified direction. Velocity is a vector quantity.

  • Mass vs. Weight:

    • Mass: A scalar quantity representing the amount of matter in an object.

    • Weight: A vector quantity representing the force acting on an object due to gravity, directed towards the center of gravity.

  • Comprehensive Classification of Scalars and Vectors:

Table comparing scalar and vector quantities

    | Scalar Quantities | Vector Quantities |     | :--- | :--- |     | Distance | Displacement |     | Speed | Velocity |     | Time | Force |     | Mass | Weight |     | Energy | Acceleration |     | Temperature | Momentum |     | — | Electric field strength |     | — | Gravitational field strength |

  • Worked Example — Defining Scalar Quantities:

    • Problem: State what is meant by a scalar quantity and give two examples.

    • Definition: A scalar quantity is a physical quantity that has magnitude only.

    • Examples (any two): Distance, Speed, Time, Mass, Energy, Temperature.

Vector Addition and Resolution

  • Vector Diagram Representation (Extended Tier Only):

    • Vectors are drawn as straight arrows in vector diagrams.

    • The length of the arrow is directly proportional to the magnitude of the vector quantity (e.g., a 4 N4\,\text{N} force arrow must be twice as long as a 2 N2\,\text{N} force arrow).

    • The direction of the arrow indicates the exact direction of the vector.

  • Component Vectors:

    • A single vector can be resolved into two perpendicular components acting at right angles to each other.

    • Component vectors are commonly represented using dashed lines and subscripts indicating orientation:

      • FVF_V represents the vertical component of force FF.

      • FHF_H represents the horizontal component of force FF.

  • Graphical Calculation Method (Scale Drawing Procedure):

    1. Choose an appropriate scale that fits the page (e.g., 1 cm=10 m/s1\,\text{cm} = 10\,\text{m/s} or 1 cm=1 N1\,\text{cm} = 1\,\text{N}) so the diagram is reasonably large (around 10 cm10\,\text{cm}).

    2. Draw the two component vectors at right angles (90∘90^\circ) to each other from a common origin.

    3. Complete the rectangle using light construction lines.

    4. Draw the resultant vector diagonally from the origin to the opposite corner of the rectangle.

    5. Measure the physical length of the resultant vector arrow using a ruler.

    6. Multiply the measured length by the scale factor to calculate the magnitude of the resultant vector.

    7. Measure the angle between the resultant vector and the reference axis using a protractor to determine direction.

  • Mathematical Calculation Method (Pythagoras & Trigonometry):

    • When two perpendicular vectors (F1F_1 and F2F_2) act at right angles to each other, their resultant vector (FRF_R) forms the hypotenuse of a right-angled triangle.

    • Magnitude calculation using Pythagoras' Theorem:

      • FR2=F12+F22F_R^2 = F_1^2 + F_2^2

      • FR=F12+F22F_R = \sqrt{F_1^2 + F_2^2}

    • Direction calculation using Trigonometry:

      • tan⁡(θ)=OppositeAdjacent=F1F2\tan(\theta) = \frac{\text{Opposite}}{\text{Adjacent}} = \frac{F_1}{F_2}

      • θ=tan⁡−1(F1F2)\theta = \tan^{-1}\left(\frac{F_1}{F_2}\right)

  • Worked Example — Perpendicular Vector Calculation:

    • Problem: A force of 60 N60\,\text{N} acts on an object to the right. A second force of 100 N100\,\text{N} acts on the same object in an upward direction. Calculate the resultant force acting on the object.

    • Step 1: Sketch a vector diagram showing 60 N60\,\text{N} horizontally to the right and 100 N100\,\text{N} vertically upwards.

    • Step 2: Calculate the magnitude using Pythagoras' theorem:

      • FR2=602+1002=3600+10000=13600F_R^2 = 60^2 + 100^2 = 3600 + 10000 = 13600

      • FR=13600≈117 NF_R = \sqrt{13600} \approx 117\,\text{N}

    • Step 3: Calculate the angle θ\theta relative to the horizontal using tangent:

      • tan⁡(θ)=10060\tan(\theta) = \frac{100}{60}

      • θ=tan⁡−1(10060)≈59∘\theta = \tan^{-1}\left(\frac{100}{60}\right) \approx 59^\circ

    • Step 4: State the final complete vector result (magnitude and direction):

      • Resultant force FR=117 NF_R = 117\,\text{N} at an angle of 59∘59^\circ above the horizontal.

  • Important Rules for Vector Problems:

    • Always provide both magnitude AND direction for vector quantities.

    • If a specific method (graphical scale drawing vs. calculation) is requested, follow that specified method. If unspecified, either method is valid.

    • In this course, the determination of resultant vectors is limited exclusively to force and velocity vectors.